• 대한기계학회논문집B
• /
• 제31권8호
• /
• pp.663-671
• /
• 2007

In this work, shape optimization of a wire-wrapped fuel assembly in a liquid metal reactor has been carried out by combining a three-dimensional Reynolds-averaged Navier-Stokes analysis with the radial basis neural network method, a well known surrogate modeling technique for optimization. Sequential Quadratic Programming is used to search the optimal point from the constructed surrogate. Two geometric design variables are selected for the optimization and design space is sampled using Latin Hypercube Sampling. The optimization problem has been defined as a maximization of the objective function, which is as a linear combination of heat transfer and friction loss related terms with a weighing factor. The objective function value is more sensitive to the ratio of the wire spacer diameter to the fuel rod diameter than to the ratio of the wire wrap pitch to the fuel rod diameter. The optimal values of the design variables are obtained by varying the weighting factor.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.47-50
• /
• 2005

본 연구의 목적은 차세대 대체에너지로 각광받는 풍력발전 중에서 육상발전보다 여러 가지 이점이 있는 해상에서의 한국형 풍력터빈 블레이드의 최적 형상을 위 한 알고리즘을 구현하는 것이다. 풍력터빈 블레이드에서 깃익형의 공기 역학적 특성은 매우 중요한 사항이다. 이를 위해서 익형 성능예측에 층류에서 난류로의 천이과정을 포함하는 XFOIL을 이용하여 블레이드 익형 단면의 양력과 항력 분포를 해석하였다. 첫 번째 수준의 설계변수는 운용범위내의 바람의 속도와 블레이드 지름, 축 회전수이며, 각 단면에서의 비틀림각과 시위길이는 두 번째 수준의 설계 변수이다. 운용범위 내의 각 설계점에서 익형의 공력 변수들과 최소에 너지손실 조건을 이용하여 시위길이와 피치각 분포를 최적화하였다. 각각의 설계점에서 결과를 바탕으로 풍력발전의 설계 운용범위에서 반응면을 구성하고 구배최적화 기법을 통해 요구동력의 제약함수를 만족하고 효율을 최대로 하는 블레이드 형상을 구현하였다. 최적형상에 대해 탈설계점 해석을 수행하여 그 성능을 구하였다.

• 전기학회논문지
• /
• 제59권6호
• /
• pp.1046-1052
• /
• 2010

In residential house, photovoltaic (PV) system among various alternatives in renewable energy system is the most efficient and feasible solution for reducing energy consumption and electricity cost. However, relatively high initial cost make people reluctant to install PV system in their houses. Therefore, in the initial state for PV system installation in the house, it is very important to decide proper capacity of the PV system considering the expected energy usage and solar energy supplying condition with the house. This paper proposes a novel optimization model for deciding appropriate capacity of the PV system for residential house. The objective function of the model is to minimize the annual cost including electricity bill, operation and maintenance cost, and annual fixed cost calculated from the initial installation cost based on capital recovery factor (CRF). The model also shows the optimal inclining angle of PV panels of the system. In this paper, we estimate the PV output using PVWATTS (PV simulator of Office of Energy Efficiency and Renewable Energy) and find optimal solutions by Sequential Quadratic Programming (SQP) method using MATLAB software. The proposed approach is finally applied to a residential model house in Gangneung, Gangwon-Do and verified its feasibility for adopting to PV system design for residential houses.

• 대한기계학회논문집A
• /
• 제27권1호
• /
• pp.144-151
• /
• 2003

In this paper, an optimum design problem for endosseous implant in dentistry is studied to find best implant design. An optimum design problem is formulated to reduce stresses arising at the cortical as well as cancellous bones, in which sufficient design parameters are chosen fur design definition that encompasses major implants in popular use. Optimization at once (OAO) with the large number of design variables, however, causes too costly solution or even failure to converge. A concept of multilevel optimization (MLO) is employed to this end, which is to group the design variables of similar nature, solve the sub-problem of smaller size fur each group in sequence, and this is iterated until convergence. Each sub-problem is solved based on the response surface method (RSM) due to its efficiency for small sized problem. Favorable solution is obtained by the MLO, which is compared to both solutions made by RSM and sequential quadratic programming (SQP) in the OAO problem.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.432-436
• /
• 2007

본 연구의 목적은 3차원 풍력터빈 블레이드 최적형상설계를 위한 실용적이고 효율적인 설계 과정을 구현하는 것이다. 국내 연안의 해상풍력에 적용하기 위해서 통계적 모델을 이용하여 풍황 자료를 분석하였다. 설계에 관련된 많은 수의 설계변수를 효과적으로 관리하기 위해서 설계과정은 운용조건 최적화와 블레이드 형상설계의 2단계로 구성하였다. 실험계획법에 의해 추출된 각 운용조건점은 형상설계를 위한 입력값으로 제공된다. 형상설계 단계에서는 최소에너지손실 조건과 결합된 BEMT를 이용하여 각 블레이드 단면에서의 시위길이와 피치각 분포를 최적화하였다. 블레이드 단면 익형은 NREL S830을 이용하였고, 익형의 공력성능은 XFOIL을 이용하여 예측하였다. 설계된 블레이드 형상의 성능해석을 수행하고 그 결과를 바탕으로 반응면을 구성하였다. 좀 더 나은 성능을 가진 블레이드 형상을 찾기 위해서 초기설계공간에서 확률적 방법을 이용하여 타당성 있는 설계공간까지 운용조건 설계변수를 이동시키고 구배최적화 기법을 통해 각각의 제약함수를 만족하면서 연평균발생에너지를 최대로 하는 최적블레이드 형상을 구현하였다. 제시된 최적설계과정은 풍력터빈블레이드 개발에 실용적이고 신뢰성 있는 설계툴로서 사용이 가능하다.

• Journal of Mechanical Science and Technology
• /
• 제19권3호
• /
• pp.768-777
• /
• 2005

This paper shows that the performance of a nonlinear fluid engine mount can be improved by an optimal design process. The property of a hydraulic mount with inertia track and decoupler differs according to the disturbance frequency range. Since the excitation amplitude is large at low excitation frequency range and is small at high excitation frequency range, mathematical model of the mount can be divided into two linear models. One is a low frequency model and the other is a high frequency model. The combination of the two models is very useful in the analysis of the mount and is used for the first time in the optimization of an engine mount in this paper. Normally, the design of a fluid mount is based on a trial and error approach in industry because there are many design parameters. In this study, a nonlinear mount was optimized to minimize the transmissibilities of the mount at the notch and the resonance frequencies for low and high-frequency models by a popular optimization technique of sequential quadratic programming (SQP) supported by $MATLAB^{(R)}$subroutine. The results show that the performance of the mount can be greatly improved for the low and high frequencies ranges by the optimization method.

• 신재생에너지
• /
• 제3권3호
• /
• pp.63-71
• /
• 2007

본 연구의 목적은 3차원 풍력터빈 블레이드 최적형상설계를 위한 실용적이고 효율적인 설계과정을 구현하는 것이다. 국내 연안의 해상풍력에 적용하기 위해서 통계적 모델을 이용하여 풍황자료를 분석하였다. 설계에 관련된 많은 수의 설계변수를 효과적으로 관리하기 위해서 설계과정은 운용조건 최적화와 블레이드 형상설계의 2단계로 구성하였다. 실험계획법에 의해 추출된 각 운용조건 설계점은 형상설계를 위한 입력 값으로 제공된다. 형상설계 단계에서는 최소에너지손실 조건과 결합된 BEMT를 이용하여 각 블레이드 단면에서의 시위길이와 피치각 분포를 최적화하였다. 블레이드 단면 익형은 NREL S830을 이용하였고, 익형의 공력성능은 XFOIL을 이용하여 예측하였다. 설계된 블레이드 형상의 성능해석을 수행하고 그 결과를 바탕으로 반응면을 구성하였다. 좀 더 나은 성능을 가진 블레이드 형상을 찾기 위해서 초기설계공간에서 확률적 방법을 이용하여 타당성 있는 설계공간까지 운용조건 설계변수를 이동시키고 구배최적화 기법을 통해 각각의 제약함수를 만족하면서 연간에너지생산량을 최대로 하는 최적블레이드 형상을 구현하였다. 제시된 최적설계과정은 풍력터빈블레이드 개발에 실용적이고 신뢰성 있는 설계툴로서 사용이 가능하다.

• Smart Structures and Systems
• /
• 제26권5호
• /
• pp.545-558
• /
• 2020

A design method of a Multiple Tuned Mass Damper (MTMD) system is presented for wind induced vibration control of a cable-supported roof structure. Modal contribution analysis is carried out to determine the dominating modes of the structure for the MTMD design. Two MTMD systems are developed for two most dominating modes. Each MTMD system is composed of multiple TMDs with small masses spread at multiple locations with large responses in the corresponding mode. Frequencies of TMDs are distributed uniformly within a range around the dominating frequencies of the roof structure to enhance the robustness of the MTMD system against uncertainties of structural frequencies. Parameter optimizations are carried out by minimizing objective functions regarding the structural responses, TMD strokes, robustness and mass cost. Two optimization approaches are used: Single Objective Approach (SOA) using Sequential Quadratic Programming (SQP) with multi-start method and Multi-Objective Approach (MOA) using Non-dominated Sorting Genetic Algorithm-II (NSGA-II). The computation efficiency of the MOA is found to be superior to the SOA with consistent optimization results. A Pareto optimal front is obtained regarding the control performance and the total weight of the TMDs, from which several specific design options are proposed. The final design may be selected based on the Pareto optimal front and other engineering factors.

• 한국자동차공학회논문집
• /
• 제16권3호
• /
• pp.166-171
• /
• 2008

In this paper, the optimization design module for the brake system of a vehicle is developed. As using this module, design variables, that minimize an object function and satisfy nonlinear constraint conditions, can be found easily. Before an optimization is operated, Plackett-Burman design, one of the factorial design methods, is used to choose the design variables which affect a response function significantly. Using the response surface analysis, second order recursive model function, which informs a relation between design variables and response function, is estimated. In order to verify the reliability of the model function, analysis of variances(ANOVA) table is used. The value of design variables which minimize the model function and satisfy the constraint conditions is predicted through Sequential Quadratic-Programming (SQP) method. As applying the above procedure to a real vehicle simulation model and comparing the values of object functions of a current and optimized system, the optimization results are verified.

• 한국정밀공학회지
• /
• 제29권6호
• /
• pp.607-612
• /
• 2012

The wear problem of wheel flange occurs at sharp curves of rail. This paper proposes a procedure for optimum design of a wheel profile wherein flange wear is reduced by improving an interaction between wheel and rail. Application of optimization method to design problem mainly depends on characteristics of design space. This paper compared local optimization method with global optimization according to sensitivity value of objective function for design variables to find out which optimization method is appropriable to minimize wear of wheel flange. Wheel profile is created by a piecewise cubic Hermite interpolating polynomial and dynamic performances are analyzed by a railway dynamic analysis program, VAMPIRE. From the optimization results, it is verified that the global optimization method such as genetic algorithm is more suitable to wheel profile optimization than the local optimization of SQP (Sequential Quadratic Programming) in case of considering the lack of empirical knowledge for initial design value.