• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.1203-1204
• /
• 2010

• Advances in materials Research
• /
• 제2권1호
• /
• pp.65-75
• /
• 2013

Heterogeneous photocatalysis is a rapidly developing field in environmental engineering. It has a great potential to cope with the increasing pollution in the air. The addition of a photocatalyst to ordinary building materials such as tiles, concrete, paints, creates environmental friendly materials by which air pollution or pollution of the surface itself can be controlled and diminished. This work reports the results of the laboratory research, especially carried out towards air purifying action and self-cleaning measurements. In particular the research was focused on the study of the photocatalytic behavior of industrially prepared tiles produced starting from commercial micro-sized $TiO_2$. Air purification action has been investigated through NOx degradation tests. On the contrary, the degradation of pollution at the surface, also called as self-cleaning action, is verified by the degradation of two different organic dyes: Rhodamine B (red color) and Metanil yellow (yellow).

• 전기학회논문지
• /
• 제59권2호
• /
• pp.338-343
• /
• 2010

Low cost motor drives are being sought for high volume energy efficient home appliances. Key to the realization of such low cost motor drives is to reduce the power electronic converter in terms of its components, particularly the active devices, finding the motor with least complexity for manufacturing and a controller that could extract the desired performance from the machine and converter combination. These and other factors such as self-starting, speed control over a wide range and most of all the crowning aspect of a four quadrant operation with bare minimum number of controllable switch (or switches) remain as formidable challenges for low cost motor drive realization. In this paper, a four quadrant switched reluctance motor (SRM) drive with only one controllable switch is realized by using a two-phase machine. The theory and operation of the proposed four-quadrant SRM drive with the proposed control algorithm for its realization are described. The motor drive is modeled, simulated and analyzed to verify its feasibility for self-starting, speed control and for four quadrant operation and the simulation results are presented. Experimental results confirm the validity of the proposed control algorithm for four quadrant control of the SRM drive. The focus of the paper is mainly directed toward the control algorithm for realizing the four-quadrant operation of the two-phase SRM drive with a single controllable switch converter.

• Wind and Structures
• /
• 제25권6호
• /
• pp.551-567
• /
• 2017

Studies of unsymmetrical blade H-Darrieus rotors at low wind speeds in terms of starting time, static torque, and power performances for different blade parameters: thickness-to-chord (t/c), camber position, and solidity are scarce. However these are required for knowing insights of rotor performances to obtain some design guidelines for the selection of these rotors. Here, an attempt is made to quantify the effects of these blade parameters on the performances of three different H-Darrieus rotors at various low wind streams. Different blade profiles, namely S815, EN0005 (both unsymmetrical), and NACA 0018 (symmetrical blade for comparison) are considered. The rotors are investigated rigorously in a centrifugal blower apparatus. Firstly the dynamic and static performances of the rotors are evaluated to determine the best performing rotor and their optimum solidity. Generalised performance equations are developed based on selected blade parameters which are validated for the unsymmetrical rotors. Further, the starting time is quantified with respect to the rotor inertia to determine the suitable range of inertia that helps the unsymmetrical blade rotor to self-start earlier than the symmetrical one. This study can work as a benchmark for the selection of optimum blade parameters while designing an unsymmetrical blade rotor at low wind speeds.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2016년도 전력전자학술대회 논문집
• /
• pp.255-256
• /
• 2016

This paper is presents a initial starting of SST with high voltage level source. Rush current flowing as difference between capacitor level and grid level can crush the whole system. Thus, industries have used initial constituted by resistance and relay. However the initial circuit used in industries can't apply high voltage application due to isolation and economic feasible problems. Therefore many countries study method can charge capacitor with another voltage sources. Also this paper introduce method charging primary side capacitor efficiently.

• 대한기계학회논문집
• /
• 제3권2호
• /
• pp.60-67
• /
• 1979

Aerodynamic forces acting on a curved blade are computed theoretically taking into account the variation of wind speed over the blade to investigate the performance of a vertical axis wind rotor. It is shown that the rotor does not self start at the rated wind speed without a supplementary starting device and that most of the power output is contributed by the central portion of the rotor, and the use of spoilers for limiting the maximum rotational speed is needed for safety. It is also shown that provision of skew angle to the blade does not improve the starting characterstics and only reduces the maximum power output. The effects of geometric variables such as skew angle, blade solidity and ratio of the rotor height to diameter are also discussed.

• 한국재료학회지
• /
• 제9권1호
• /
• pp.51-56
• /
• 1999

The $BaTiO_3$ powders were synthesized by GNP (Glycine-Nitrate process). The powders were prepared using carbonate and alkoxide as starting materials and nitric acid was used as a solvent for starting materials as well as an oxidant for combustion. the effects of aggregates in $BaTiO_3$ powders on green densities, sintering and dielectric characteristics were investigated. When the glycine/cation molar ratio was 1.2, reactivity of self-combustion was most intensive and the degree of aggregates after calcination was low. On sintering at $1400^{\circ}C$, maximum theoretical relative density(94.99%%0 was obtained in case of 1.2 molar ratio of glycine/cation. The dielectric constant of this sintered $BaTiO_3$ was 1919.

• 한국가시화정보학회지
• /
• 제13권1호
• /
• pp.21-25
• /
• 2015

Three-dimensional vortex structures in the corner region of translating normal plates are visualized experimentally with defocusing digital particle image velocimetry. Vortex formation processes for three plates with corner angle $60^{\circ}$, $90^{\circ}$, and $120^{\circ}$ are compared in order to study the effect of corner shape on vortex formation. In all cases, the self-induction of the starting vortex and its interaction with the potential flow induced by the moving plate cause the vortex to change its form dynamically after the plate starts to translate. While the vortex near a corner follows the plate in the low corner angle of $60^{\circ}$, the vortex separates early from the plate and its forward motion becomes slow in the high corner angle of $120^{\circ}$. It is also found that the starting vortex can transport inward at the corner, which depends on the corner angle.

• Bulletin of the Korean Chemical Society
• /
• 제30권5호
• /
• pp.1012-1020
• /
• 2009

We developed an efficient three-step synthetic protocol of $\gamma$-hydroxybutenolides starting from the Baylis-Hillman adducts: (i) bromination, (ii) Barbier reaction and (iii) one-pot $K_2CO_3$-mediated synthesis of $\gamma$-hydroxybutenolides. In addition, we showed the synthetic applicability of butenolides including self-dimerization, conjugate addition reaction, and alkylations.

• 한국연초학회지
• /
• 제16권2호
• /
• pp.102-107
• /
• 1994

This study was conducted to transfer the potato virus Y-necrosis strain resistance from Nicotiana africana to Nicotiana tabacum (cv. NC82) N. africana was crossed with NC82, GErmination of the cotyledon stage, at which time most of the seedling died. However, surviving seedlings continued to grow normally. Chromosomes of the these interspecific self-sterile F1 hybrids were doubled by tissue culture. Amphidiploid of F1 hybrid was self-fertile. Starting with amphidipliod, a wystematic backcross (BC) program was set up with NC82 as recurrent parent. In the BC5C2 generation, the resistant plant was selected. This resistant line, KF8833-1, had 48 chromosome and secreting glandular trichomes. It flowered 2days later than NC82, and stalk height, leaves per plant, leaf length and leaf width were similar to those of NC82.