• 한국광학회:학술대회논문집
• /
• 한국광학회 2004년도 제15회 정기총회 및 동계학술발표회
• /
• pp.150-151
• /
• 2004

• Journal of the Optical Society of Korea
• /
• 제19권3호
• /
• pp.255-259
• /
• 2015

We have proposed and experimentally verified a pulse-width modulation (PWM) generator which directly generated a PWM signal in the optical domain. Output waveforms were clear at the repetition rate of 16 MHz; the duty cycle (DC) was from 14.7% to 72.1%; and the DC-control resolution was about 4.399%/dB. The PWM generator' operation principle is based on the injection-locking property of a single-mode Fabry-$P{\acute{e}}rot$ laser diode (SMFP-LD). The SMFP-LD, which has a self-locked mode wavelength at ${\lambda}_{PWM}$, was used to detect the power of the injection-locking signal (optical analog input). If the analog input power is high, the SMFP-LD is locked to the wavelength of the input signal ${\lambda}_a$ and there is no output after an optical bandpass filter (OBF). If the analog input power is low, the SMFP-LD is unlocked and there is output signal at ${\lambda}_{PWM}$ after the OBF. Thus, the SMFP-LD plus the OBF provide digital output for an analog input. The DC of the output PWM signal can be controlled by tuning the power of the analog input.

• 제어로봇시스템학회논문지
• /
• 제17권8호
• /
• pp.824-832
• /
• 2011

An essential consideration to differentiate prosthetic hand from robot hand is its convenience and usefulness rather than high resolution or multi-function of the robot hand. Therefore, this study proposes a myoelectric hand with a 2 DOF auto wrist module which has 6 essential functions of the human hand such as open, grasp, pronation, supination, extension, flexion, which improves the convenience of the daily life. It consists of the 3 main parts, the myoelectric sensor for input signal without additional attachment to operate the prosthetic hand, hand mechanism with high-torqued auto-transmission mechanism and self-locking module which guarantee the safety under the abrupt emergency and minimum power consumption, and dual threshold based controller to make easy for adopting the multi-DOF myoelectric hand. We prove the validity of the proposed system with experimental results.

• 로봇학회논문지
• /
• 제17권2호
• /
• pp.238-244
• /
• 2022

Maintenance works of offshore wind turbines could take a longer time, which causes the reduction of their energy production efficiency, than those of onshore wind turbines owing to severe offshore environment. Subsequently, preventive maintenance measures are required to increase the production efficiency. Thus, we proposed a wheel-based Underwater Pole Climbing Robot (UPCR) platform, which was aimed at the periodic inspection and maintenance of the substructures of the offshore wind turbines, with three advantages: high speed, good mobility and low power consumption. In the proposed platform, a self-locking system using a gripper module was adopted for preventing slippery problem and a dual configuration was chosen for moving on a branched structure. As a result, the proposed robot was able to continuously climb, preserve it's position at the pole without consuming energy, and move from the pole to the other branched pole. The results of this research show that the UPCR has basic moving capabilities required for the underwater work for the substructures of the offshore wind turbines.

• ETRI Journal
• /
• 제25권3호
• /
• pp.149-155
• /
• 2003

A self-pulsating multisection distributed-feedback laser diode (DFB LD) can potentially realize all-optical clock extraction. This device generally consists of three sections, two DFB sections and one waveguide section. The most important variable in this device is detuning, which is the relative spectral position between the stop bands of two DFB sections. We fabricated a novel structure in which two gratings were located one over and one under the active layers. Each grating structure was independently defined in processing so that detuning, which is the prerequisite for self-pulsation, could be easily controlled. Observing various self-pulsating phenomena in these devices under several detuning conditions, we characterized the phenomena as dispersive Q-switching, mode beating, and self-mode-locking.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 통신소사이어티 추계학술대회논문집
• /
• pp.86-89
• /
• 2003

In this paper, Self-Oscillating Mixer is designed by oscillator that was based on a general nonlinear input-output model for the subharmonic injection locked oscillator is analysed. We have designed and fabricated the Self-Oscillating Mixer for 5GHz by proposed subharmonic injection locked oscillator based frequency synthesizer structure that have characteristic of good frequency sensitivity, good phase noise. The design strategy leading to an optimized SILO with regards to its locking range is described and a test SOM circuit is demonstrated a 4dB conversion gain at 280MHz IF frequency from the carrier.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2003년도 제14회 정기총회 및 03년 동계학술발표회
• /
• pp.40-41
• /
• 2003

(self-focusing)을 이용한 커렌즈 모드록킹(Kerr-lens mode-locking； KLM) 방법을 이용하면 간단한 구조를 갖는 공진기로 100 펨토초(femto=10-13) 미만의 레이저 펄스를 생성할 수 있다. KLM 티타늄사파이어(Ti：sapphire) 레이저의 발달로 10 펨토초 영역의 레이저 펄스를 간단하게 생성할 수 있게 되었으며 특히, 넓은 스펙트럼 폭을 가지는 처프거울(chirped mirror)의 사용과 정확한 분산의 보정을 통한 5 펨토초(800 nm 파장의 두 주기에 해당) 영역의 레이저 펄스 생성도 보고되고 있다.

• Journal of Power Electronics
• /
• 제16권4호
• /
• pp.1513-1525
• /
• 2016

Rapid and accurate phase synchronization is critical for the reliable control of grid-tied inverters. However, the commonly used software phase-locked loop methods do not always satisfy the need for high-speed and accurate phase synchronization under severe grid imbalance conditions. To address this problem, this study develops a novel open-loop phase locking scheme based on a synchronous reference frame. The proposed scheme is characterized by remarkable response speed, high accuracy, and easy implementation. It comprises three functional cascaded blocks: fast orthogonal signal generation block, fast fundamental-frequency positive sequence component construction block, and fast phase calculation block. The developed virtual orthogonal signal generation method in the first block, which is characterized by noise immunity and high accuracy, can effectively avoid approximation errors and noise amplification in a wide range of sampling frequencies. In the second block, which is the foundation for achieving fast phase synchronization within 3 ms, the fundamental-frequency positive sequence components of unsymmetrical grid voltages can be achieved with the developed orthogonal signal construction strategy and the symmetrical component method. The real-time grid phase can be consequently obtained in the third block, which is free from self-tuning closed-loop control and thus improves the dynamic performance of the proposed scheme. The proposed scheme is adaptive to severe unsymmetrical grid voltages with sudden changes in magnitude, phase, and/or frequency. Moreover, this scheme is able to eliminate phase errors induced by harmonics and random noise. The validity and utility of the proposed scheme are verified by the experimental results.

• 한국지진공학회논문집
• /
• 제11권6호
• /
• pp.63-68
• /
• 2007

이 연구에서는 새로운 접합장치인 자동체결장치(Self-Locking Connectors)를 사용한 강재보-PC기둥 접합부의 내진성능에 대한 연구를 수행하였다. PC기둥(또는 합성기둥)과 강재보로 이루어진 합성모멘트골조는 각각의 재료의 장점을 최대한으로 이용한 합리적인 구조형식이다. 그러나 서로 다른 두 재료 사이의 접합에 따른 어려움으로 인해 접합부의 상세가 복잡해지고 제작비가 상승하는 단점을 가지고 있다. 반면에 자동체결장치는 쐐기의 원리를 이용한 접합장치로서 시공이 단순한 장점이 있다. 또한 자동체결장치를 사용한 접합부는 용접을 사용하지 않음으로써 기존의 접합부에 비해 내진성능을 개선할 수 있다. 본 연구에서는 자동체결장치를 사용한 강재보-PC기둥(또는 합성기둥) 접합부에 대한 내진성능을 검증하기 위해 반복하중 실험을 수행하였다. 실험결과 자동체결장치를 사용한 보-기둥 접합부는 우수한 내진성능을 발휘할 수 있는 것으로 나타났다.

• 대한기계학회논문집A
• /
• 제21권12호
• /
• pp.2121-2133
• /
• 1997

A finite element code is developed for 3-D self-contact problems, using continuum elements with a SRI(Selective Reduced Integration) scheme to prevent locking phenomenon by the incompressibility of rubber. Contact treatment is carried out in two ways : using the displacement constraints in case of rigid contact ; and imposing the same contact forces on two contact boundaries in case of self-contact. The finite element code developed is applied to the deformation analysis of C.V.joint boots which maintain lubrication conditions and protect the C.V.joint assembly from impact and dust. The boot accompanies large rotation depending on the rotation of the wheel axis and leading to the self-contact phenomena of the boot bellows. Since this contact phenomenon causes wear of the product and has great influence on the endurance life of the product, it is indispensable to carry out stress analysis of the rubber boots. In case of self-contact, various methods for determining contact forces have been suggested with an appropriate contact formulation. Especially, the types of penetration in self-contact are modularized to accelerate conputation with a contact algorithm.