• Korean Journal of Food Science and Technology
• /
• v.27 no.4
• /
• pp.582-592
• /
• 1995

To measure rheological properties of the starch dough, an Extrusion Capillary Viscometer(ECV) cell was self-made and attached to Instron machine(Model 1140). Apparent viscosities of corn and waxy corn starch doughs were measured and their gelatinization degrees were determined by enzymatic analysis. When corn and waxy corn starch doughs with $36{\sim}52%$ moisture content were heated at $60{\sim}100^{\circ}C$, come-up time of the cold point of doughs decreased from 220 sec to 140 sec with increased in the moisture content. In the measurement range of $36{\sim}52%$ moisture content and $60{\sim}100^{\circ}C$ heating temperature, both corn and waxy corn starch doughs showed pseudoplastic flow behaviors. At the same shear rate, both shear stress and viscosity of starch dough decreased as the moisture content increased. At the moisture content above 44%, the shear stress and viscosity of starch dough decreased as the heating temperature increased from $60^{\circ}C\;to\;70^{\circ}C$, but increased as the heating temperature increased from $80^{\circ}C\;to\;100^{\circ}C$. When the moisture content increased and heating temperature, the gelatinization degree of starch dough increased from about 10% to about 62%. The gelatinization degree of waxy corn starch dough was $15{\sim}20%$ higher than that of corn starch dough under the same gelatinization conditions. The effects of moisture content on the viscosity of starch dough were examined by Arrhenius equation. As the moisture content increased, viscosity of starch dough decreased. But the effect of moisture content was greater in the range of $80{\sim}100^{\circ}C$ than in the range of $60{\sim}70^{\circ}C$ heating temperature.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.3
• /
• pp.116-123
• /
• 2020

Ion beam irradiation induces self-organization of nanostructure on the surface of polymer film. We show that the incident angle of Ar ions on polyethylene naphthalate(PEN) film changes self-organized nanostructure. PEN film was irradiated by argon ion beams with the ion incident angle of 0°, 30°, 45°, 60°, and 80°. Nanostructure was altered from dimple to ripple structure as the angle increases. The ripple structure changed to pillar structure after 60°due to that the shallow incident angle increased the ion energy transfer per depth up to 50 eV/Å, which value could induce excessive surface heating and oligomer formation reacting as a physical mask for anisotropic etching. And quantitative analysis of the nanostructures was adapted by using ABC model and fractal dimension theory.

• Journal of the Korean Society of School Health
• /
• v.11 no.2
• /
• pp.171-187
• /
• 1998

In recent years, adolescent issues including smoking, drinking, drug abuse, juvenile delinquency, deviant sexual behavior, mental health problems, high suicide rate, juvenile delinquency and absence without due notice, etc are emerging as serious social problems and the debate on these controversial issues is heating up. The previous studies on adolescent health behavior and social juvenile delinquency such as run-away from home and absence without due notice have been conducted mostly by cause analysis utilizing social demographic factors or biological factors. In other words, the main factors analyzed were demographic and economic factors or parent's educational level, etc, which were the fixed environmental ones that were unable to cause the change in the health behavior. Accordingly, the purpose of this study is to analyze factors which are changeable and fixable among the factors influencing the adolescent's health behavior and misconducts and, eventually influencing factors which can be used as the basis to establish health policies and health promotion program to reduce the health risk behavior and misconducts of adolescents. The study subjects were selected by dividing senior high school student in Seoul by region and through random sampling. The 890 subjects were selected from 10 schools including the preparatory school, vocational schools and institutional schools. The duration of the study was for July 1-5, 1997 for the first survey and the second one, for August 25-September 10. Regarding the analysis method, the SAS program was used. The adoptablity of theoretical model was tested through covariance structural analysis utilizing PC-LISREL 8.12 Program. The major findings of the study are as follows: As a result of establishing the model of factors influencing health behavior and juvenile delinquency, in case of male students as the health behavior self-efficacy, education level of fathers, economic level, self-control and the health interest of parent were higher, students were more likely to practice the health promoting behavior. Juvenile delinquency and health risk behavior were prevalent among those with the less shyness, the lower health behavior self-efficacy, lower self-control, lower self-assertiveness, lower economic level. The self-control was the most powerful factor. In case of female students, those with higher health behavior self-efficacy were more likely to practice the health promoting behavior whereas those with lower health behavior self-efficacy, lower self-control, lower self- assertiveness, less shyness were more likely to practice health risk behavior and juvenile delinquency. In case of prep schools, those with higher health behavior self-efficacy and better perceived health status were more likely to practice the health promoting behavior while those with less shyness, lower health behavior self-efficacy and lower academic achievement were more likely to engage in health risk behavior and juvenile delinquency. In case of vocational schools, as health behavior self-efficacy and economic level were higher, the practice rate of health promoting behavior was higher. As the self-control, shyness, self-assertiveness, health behavior self-efficacy were lower, the rate of health risk behavior and juvenile delinquency were higher. In case of social institutional schools, as, the health behavior self-efficacy, social support and economic level, health interest of parents were higher, the rate of health promoting behavior were higher. As the self-control, shyness, self-assertiveness, health behavior self-efficacy and social support were lower, the rate of health risk behavior and juvenile delinquency were higher. So the health promoting behavior was positively related to the health behavior self-efficacy, health interest of parents, social support, education level of fathers, level of perceived health status, economic level. The health risk behavior and juvenile delinquency were higher with the lower health behavior self-efficacy, self-control and self-assertiveness, lower health locus control, less shyness and loneliness, lower economic level and academic achievement. In conclusion, the health risk behavior and juvenile delinquency can be reduced by enhancing self-control, self-assertiveness, health behavior self-efficacy and social support. According to the final model drawn by connecting health behavior and juvenile delinquency, the reduction of health risk behavior can greatly contribute to decreasing social juvenile delinquency as the process of juvenile delinquency was extended from common behaviors to problem behaviors and further into juvenile delinquency.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.7
• /
• pp.4489-4493
• /
• 2014

LED light driving device has problems in efficiency and heating at higher than 150W. In addition, there is inconvenience in replacing the lighting device to another when W is not the same as the previous one. In this paper, a multi-channel LED light driver, driver embedded driver circuit in a multi-channel structure with a power system in the driver-interlocking structure was designed. With the auto control converter structure with a power efficiency above 93% and power factor above 0.98, the weight of the high efficiency LED lighting-actuating device in driver-interlocking structure, a driver in self-calibrating self-optimization structure. In this paper, at below 10% THD, the existing converter contrast weight was reduced by 40% or more.

• Journal of Powder Materials
• /
• v.11 no.4
• /
• pp.294-300
• /
• 2004

This study for preparation of aluminum nitride (AlN) with high purity was carried out by self-propagating high-temperature synthesis method in two different systems, $Al-N_{2}$ and $Al-N_{2}$-AlN, with the change of nitrogen gas pressure and dilution factor. On the occasion of $Al-N_{2}$ system, unreacted aluminum was detected in the product in spite of high nitrogen pressure, 10 MPa, This may be caused by obstructing nitrogen gas flow to inner part of molten and agglomerate of aluminum, formed in pre-heating zone. In $Al-N_{2}$-AlN system, AlN with a purity of 95% or ever can be prepared in the condition of $f_{Dil}\geq0.5$, $P_{N_{2}}\geq$ 1 MPa, and the purity can be elevated to 98% over in the condition of $f_{Dil}$ = 0.7 and $P_{N_{2}}$ = 10 MPa.

• Tribology and Lubricants
• /
• v.10 no.3
• /
• pp.29-38
• /
• 1994

The friction and wear of mild steel at dry sliding surfaces under different vacuum conditions have been investigated to understand the wear mechanisms. For the test, a ball-ondisk typed wear-rig has been built and implemented, allowing control of sliding speed, load and vacuum. Results show that, at a high sliding velocity, friction of low carbon steel (SS41) under a high vacuum is much higher than that of ambient condition and wear is much severer. It is due to lack of effective oxidation film formation on which steel surfaces could protect themselves against the severe wear. It has been shown, however, that there is a critical regime with contact conditions (at a low sliding velocity, a low load, and under a medium vacuum) at which effective, protective films of low carbon steel have been built on the surfaces in a friction process with a self-regulating way, resulting in both very low coefficients of friction (about 0.3) and mild wear. In order to investigate the protective films on steel surfaces, the worn surfaces and the wear debris have been experimentally analyzed with SEM, AES/SAM and XRD. A theoretical analysis of frictional heating at sliding surfaces, and an experimental analysis of the influence of oxidation wear under various vacuum conditions are described. The important variables on which self-formations of protective films at dry sliding surfaces depend, and the wear mechanisms are also investigated.

• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.1
• /
• pp.62.1-62.1
• /
• 2018

Galaxies in the cluster environment interact with the intracluster medium (ICM), losing the interstellar medium (ISM) and alternating their evolution. Observational evidences of the extraplanar ISM stripped by the ICM's ram pressure are prevalent in HI imaging studies of cluster galaxies. However, current theoretical understanding of the ram pressure stripping (or ICM-ISM interaction in general) is still limited mainly due to the lack of numerical resolution at ISM scales in large-scale simulations. Especially, self-consistent modeling of the turbulent, multiphase ISM is critical to understand star formation in galaxies interacting with the ICM. To achieve this goal, we utilize the TIGRESS simulation suite, simulating a local patch of galactic disks with high resolution to resolve key physical processes in the ISM, including cooling/heating, self-gravity, MHD, star formation, and supernova feedback. We then expose the ISM disk to ICM flows and investigate the evolution of star formation rate and the properties of the ISM. By exploring ICM parameter space, we discuss an implication of the simple ram pressure stripping condition (so called the Gunn-Gott condition) to the realistic ISM.

• Journal of the Korean Ceramic Society
• /
• v.31 no.5
• /
• pp.552-560
• /
• 1994

A composite of TiB2-Al2O3 system was successfully prepared from a mixture of TiO2, B2O3, and Al by self-propagating high temperature synthesis (SHS) with a novel characteristic, utilizing the internal oxidation heat of aluminium metal of the mixture, instead of by a conventional technique, externally heating a mixture of Ti, B and Al2O3. From a mixture with B/Ti molar ratio of =2.0, pure two phases of TiB2 and $\alpha$-Al2O3 with good crystallinity and small, uniform sizes were formed. However, when the B/Ti molar ratio of the mixture goes to a value less than 2.0, in addition to the above main minerals, a small smounts of metastable phases such as TiB and Ti3B4 were formed. It was found that about 60%, the optimum green density of compacts gave their highest reaction rate and temperature during SHS process. TiB2-Al2O3 system composite with B/Ti molar ratio of =2.0 could be pressurelessly sintered even at 190$0^{\circ}C$ under Ar gas flows without any addition of sintering aids, showing their good properties such as 91.2% in relative density, 2750 kgf/$\textrm{mm}^2$ in Vickers hardness and 2620 kgf/$\textrm{cm}^2$ in flexural strength.

• Journal of Power System Engineering
• /
• v.9 no.1
• /
• pp.14-22
• /
• 2005

This work deals with a controlled auto-ignition (CAI) single cylinder gasoline engine, focusing on the extension of operating conditions. The fuel is injected indirectly into electrically heated inlet air flow. In order to keep a homogeneous air-fuel mixing, the fuel injector is water-cooled by a specially designed coolant passage. Investigated are the engine performance and emission characteristics under the wide range of operating conditions such as 40 in the air-fuel ratio, 1000 to 1800 rpm in the engine speed, $150\;to\;180^{\circ}C$ in the inlet-air temperature, and $80^{\circ}$ BTDC to $20^{\circ}$ ATDC in the injection timing. A controlled auto-ignition gasoline engine can be achieved that the ultra lean-burn with self-ignition of gasoline fuel by heating inlet air. It can be achieved that the emission concentrations of carbon monoxide, hydrocarbons and nitrogen oxide had been significantly reduced by CAI combustion compared with conventional spark ignition engine.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.314-314
• /
• 2010

For the optimal design of a tokamak-type reactor, self-consistent determination of a radial build of reactor systems is important and the radial build has to be determined by considering the plasma physics and engineering constraints which inter-relate various reactor systems. In a low aspect ratio (LAR) tokamak reactor with a superconducting toroidal field (TF) coil, the shield should provide sufficient protection for the superconducting TF coil and the shield plays a key role in determining the size of a reactor. To determine the radial build of a reactor, neutronic effects such as tritium breeding in the blanket, nuclear heating, and radiation damage to toroidal field (TF) coil has to be included in the systems analysis. In this work, the outboard blanket only is considered where tritium self-sufficiency is possible by using an inboard neutron reflector instead of breeding blanket. The reflecting shield should provide not only protection for the superconducting TF coil but also improved neutron economy for the tritium breeding in outboard blanket. Tungsten carbide, metal hydride such as titanium hydride and zirconium hydride can be used for improved shielding performance and thus smaller shield thickness. With the use of advanced technology in the shield, conceptual design of a compact superconducting LAR reactor with aspect ratio of less than 2 will be presented as a viable power plant.