• Journal of Korean Society of Water and Wastewater
• /
• 제23권6호
• /
• pp.769-778
• /
• 2009

Performances and internal behaviors of the upflow hybrid anaerobic filters treating a dairy wastewater were analyzed to identify the functions and roles of the modular crossflow media and sludge bed layer and to discover their interrelationship in the filter. The media could perform independent biological and physical separation role without buildup of sludge bed, while the role of sludge bed was dependent on the function of the media. The filter packed with the crossflow media did not necessarily require the formation of sludge bed when treating a dairy wastewater. Biological contribution of the media was controlled by that of biologically active sludge bed complementing mutually each other. The gas-liquid-solid separation capability of the media was indispensible to ensure the active biological role of sludge bed, since sludge bed buildup without the media had no independently effective biological function. It was believed that the filter in itself could also function as a selector for physical gas-liquid-solid separation resulting in selectively concentrating particles with superior settleability in sludge bed. The sludge bed in the filter played a key role in the physical solids capture from influent as well as biological organics removal.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• 제14권4호
• /
• pp.219-225
• /
• 2014

The New efficient Mux-based scan latch cell design and scan test of LOS/LOC modes are proposed for detection of delay faults in digital logic circuits. The proposed scan cell design can support LOS(Launch-off-Shift) and LOC(Launch-off-Capture) tests with high fault coverage and low scan power and it can alleviate the problem of the slow selector enable signal and hold signal by supporting the logic capable of switching at the operational clock speeds. Also, it efficiently controls the power dissipation of the scan cell design during scan testing. Functional operation and timing simulation waveform for proposed scan hold cell design shows improvement in at-speed test timing in both test modes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제28권8호
• /
• pp.976-983
• /
• 2004

In high-density hard disk drives, the slider should be made to fly close to the magnetic recording disk to generate better signal resolution and at an increasingly high velocity to achieve better data rate. The slider disk interaction in CSS (contact-start-stop) mode is an important source of particle generation. Contamination particles in the hard disk drive can cause serious problems including slider crash and thermal asperities. We investigated the number and the sizes of particles generated in the hard disk drive, operating at increasing disk rotational speeds, in the CSS mode. CNC (condensation nucleus counter) and PSS (particle size selector) were used for this investigation. In addition, we examined the particle components by using SEM (scanning electron microscopes), AES (auger electron spectroscopy), and TOF-SIMS (time of flight-secondary ions mass spectrometry). The increasing disk rotational speed directly affected the particle generation by slider disk interaction. The number of particles that were generated increased with the disk rotational speed. The particle generation rate increased rapidly at motor speeds above 8000 rpm. This increase may be due to the increased slider disk interaction. Particle sizes ranged from 14 to 200 nm. The particles generated by slider disk interaction came from the lubricant on the disk, coating layer of the disk, and also slider surface.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제24권7호
• /
• pp.537-542
• /
• 2011

Recently, n-InZnO/p-CuO oxide diode has attracted great attention due to possible application for selector device of 3-dimensional cross-point resistive memory structures. To investigate the detailed properties of InZnO (IZO), we have deposited IZO films on the fused quartz substrate using PLD (pulsed laser deposition) method at oxygen pressure of 1~100 mTorr and substrate temperature of RT$\sim600^{\circ}C$. The influence of oxygen pressure and substrate temperature on structural, optical and electrical of IZO films is analyzed using XRD (x-ray diffraction), SEM (scanning electron microscopy), UV-Vis spectrophotometry, spectroscopic ellipsometry (SE) and hall measurements. The XRD results shows that the deposited thin films are polycrystalline over $300^{\circ}C$ of substrate temperature independent of oxygen pressure. The resistivity of films was increased as oxygen pressure and substrate temperature decrease. The thickness and optical constants of the deposited films measured with UV-Vis spectrophotometer were also compared with those of broken SEM and SE results.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• 제45권8호
• /
• pp.54-60
• /
• 2008

The bus architecture consists of a master initiating a communication transaction, a slave responding to the transaction, a arbiter selecting a master, a bridge connecting buses and so on. Recently this is more complicated and developed toward multi-bus architecture. In this paper, several cases of multi-shared bus architecture are discussed and in order to decrease the bridge latency, the architecture introducing a memory selector is proposed. Finally, a LCD controller using DMA master is integrated in this bus architecture that is verified due to RTL simulation and FPGA board test. DMA, LCD line buffer and SDRAM controller are normally operated in the timing simulation using ModelSim tool, and the LCD image is confirmed in the real FPGA board containing LCD panel.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제17권7호
• /
• pp.666-676
• /
• 1992

In this paper, algorithm and testable circuit to find all PSF(Pattern Sensitive Fault ) occured in RAM were proposed. Conventional test circuit and algorithm took much time in testing because consecutive test for RAM cells or f-dimensional memory struciure was not employed. In this paper, methodology for parallel RAM-testing was proposed by compensating additional circuit for test to conventional RAM circuit. Additional circuits are parallel comparator, error detector, group selector circuit and a modified decoder used for parallel testing. And also, the constructive method of Eulerian path to obtain efficient test pattern was performed. Consequently, If algorithm proposed in this paper Is used, the same operations as 32sxwor4 lines will be needed to test b x w=n matrix RAM. Circuit simulation was performerd, and 10 bits x :If words testable RAM was designed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제37B권12호
• /
• pp.1128-1137
• /
• 2012

In this paper, we propose an improved MPR selection method considering mobility and density of nodes for ad-hoc networks. In Optimized Link State Routing(OLSR), a node selects 1-hop Multi-Point Relay(MPR) nodes to cover all 2-hop neighbor nodes. In a high population area, many nodes are likely to be selected as MPR nodes by their neighbors. This leads to increase in contention among MPR nodes and may decrease overall performance of the network. In addition, when an MPR node leaves the communication range of its MPR selector node, it can no longer perform as the MPR node and the performance of the network may also decrease. In this paper, we propose an MPR selection method which measures the mobility and density of nodes by exchanging the hello messages and gives the priorities to the nodes for MPR selection. Performance evaluation results using OPNET show that the proposed method is superior to OLSR or the MPR candidate method in terms of connectivity and throughput.

• Journal of KIISE:Software and Applications
• /
• 제35권2호
• /
• pp.91-104
• /
• 2008

Service-Oriented Computing (SOC) is the development method that published services are selected and composed at runtime to deliver the expected functionality to service clients. SOC should get maximum benefits not only supporting business agility but also reducing the development time. Services are selected and composed at runtime to improve the benefits. However, current programming language, SOC platforms, business process modeling language, and tools support either manual selection or static binding of published services. There is a limitation on reconfiguring and redeploying the business process to deliver the expected services to each client. Therefore, dynamic selection is needed for composing appropriate services to service clients in a quick and flexible manner. In this paper, we propose Dynamic Selection Handler (DSH) on ESB. we present a design method of Dynamic Selection Handler which consists of four components; Invocation Listener, Service Selector, Service Binder and Interface Transformer. We apply appropriate design patterns for each component to maximize reusability of components. Finally, we describe a case study that shows the feasibility of DSH on ESB.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• 제15권1호
• /
• pp.175-182
• /
• 2011

In this paper, we implemented a high-performence memory controller which can accommodate processing blocks(multiple masters) in SoC for video signal processing. The memory controller is arbitrated by the internal arbiter which receives request signals from masters and sends grant and data signals to masters. The designed memory controller consists of Master Selector, Mster Arbiter, Memory Signal Generator, Command Decoder, and memory Signal Generator. It was designed using VHDL, and verified using the memory model of SAMSING Inc. For FPGA synthesis and verification, Quartus II of ATERA Inc. was used. The target device is Cyclone II. For simulation, ModelSim of Cadence Inc was used. Since the designed H/W can be stably operated in 174.28MHz, it satisfies the specification of SDRAM technology.

• Korean Journal of Materials Research
• /
• 제27권1호
• /
• pp.32-38
• /
• 2017

Insulating $TaN_x$ films were grown by plasma enhanced atomic layer deposition using butylimido tris dimethylamido tantalum and $N_2+H_2$ mixed gas as metalorganic source and reactance gas, respectively. Crossbar devices having a $Pt/TaN_x/Pt$ stack were fabricated and their electrical properties were examined. The crossbar devices exhibited temperature-dependent nonlinear I (current) - V (voltage) characteristics in the temperature range of 90-300 K. Various electrical conduction mechanisms were adopted to understand the governing electrical conduction mechanism in the device. Among them, the PooleFrenkel emission model, which uses a bulk-limited conduction mechanism, may successfully fit with the I - V characteristics of the devices with 5- and 18-nm-thick $TaN_x$ films. Values of ~0.4 eV of trap energy and ~20 of dielectric constant were extracted from the fitting. These results can be well explained by the amorphous micro-structure and point defects, such as oxygen substitution ($O_N$) and interstitial nitrogen ($N_i$) in the $TaN_x$ films, which were revealed by transmission electron microscopy and UV-Visible spectroscopy. The nonlinear conduction characteristics of $TaN_x$ film can make this film useful as a selector device for a crossbar array of a resistive switching random access memory or a synaptic device.