• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.121-128
• /
• 1998

In this study, when tension and bending stress act on plate simultaneously, stress intensity factor is analyzed at crack tip with using BEM(Boundary Element Method). In this analysis, stress intensity factors(S.I.F) are defined for variable ligament, aspect and stress ratio($\sigma$T/$\sigma$B). Consequently, predicted that crack grow to depth direction at low aspect and ligament ratio in tension stress and to surface direction in bending stress. Tension and bending stress act on plate same time, effect of tension stress in the first stage and effect of bending stress in the after stage was to observed. The outbreak of secondary crack in backside is under the control of stress amplitude and predict that the point of outbreak is mear backside.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.234-239
• /
• 2001

The stress intensity factors have been widely used in numerical studies of crack growth direction. However in many cases, omissive terms of the series expansion are quantitatively significant, so we consider the computation of such terms. For this purpose, we used the finite element method with isometric quadratic quarter-point elements. For examples, infinite square plate with a slant crack subjected to a uniaxial load is analyzed. The numerical analysis were performed for the wide range of crack tip element lengths and inclined angles. The numerical results obtained are compared with the theoretical solutions. Also they were accurate and efficient.

• Nuclear Engineering and Technology
• /
• v.49 no.4
• /
• pp.838-849
• /
• 2017

This paper proposes penalty factor equations that take into consideration the weld strength over-match given in the classified form similar to the revised equations presented in the Code Case N-779 via cyclic elastic-plastic finite element analysis. It was found that the $K_e$ analysis data reflecting elastic follow-up can be consolidated by normalizing the primary-plus-secondary stress intensity ranges excluding the nonlinear thermal stress intensity component, $S_n$ to over-match degree of yield strength, $M_F$. For the effect of over-match on $K_n{\times}K_{\nu}$, dispersion of the $K_n{\times}K_{\nu}$ analysis data can be sharply reduced by dividing total stress intensity range, excluding local thermal stresses, $S_{p-lt}$ by $M_F$. Finally, the proposed equations were applied to the weld between the safe end and the piping of a pressurizer surge nozzle in pressurized water reactors in order to calculate a cumulative usage factor. The cumulative usage factor was then compared with those derived by the previous $K_e$ factor equations. The result shows that application of the proposed equations can significantly reduce conservatism of fatigue assessment using the previous $K_e$ factor equations.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.1
• /
• pp.59-65
• /
• 2004

The stress intensity factors have been widely used in numerical studies of crack growth direction. However in many cases, omissive terms of the series expansion are quantitatively significant, so we consider the computation of such terms. For this purpose, we used the finite element method with isoparametric quadratic quarter-point elements. For examples, infinite square plate with a slant crack subjected to a uniaxial load is analyzed. The numerical analysis were performed for the wide range of crack tip element lengths and inclined angles. The numerical results obtained are compared with the theoretical solutions. Also they were accurate and efficient.

• Journal of the Korean Institute of Gas
• /
• v.7 no.2 s.19
• /
• pp.22-32
• /
• 2003

Al-brass material is generally used at the state of plastic deformation, for example; bending, extension of bell mouth at shell and tube type heat exchanger. And SCC(stress corrosion cracking) of Al-brass material will be affected by residual stress as plastic deformation. SCC results from synergism between mechanical factor and corrosion environment. Mechanical factor is stress that directly relates with stress intensity factor at the crack tip. This paper was studied on the effect of stress on SCC of Al-brass tube under in $3.5\%$ NaCl. + $0.1\%\;NH_4OH$ solution by constant displacement tester. Increasing of acidified water flow into sea and speeds up corrosion rate of Al-brass which is used as a tube material of vessel heat exchanger by polluted coast seawater. The experimental results are as follow The latent time of SCC occurrence gets longer as the initial stress intensity factor($K_{Ii}$) gets lower The main crack was propagated as the initial stress intensity factor($K_{Ii}$) gets higher, and secondary cracks occurred by electro-chemical factor a(ter stage of released stress. Dezincification phase showed around the crack, and the range of dezincification gets wider as the initial stress intensity factor($K_{Ii}$) gets higher.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1386-1388
• /
• 2003

In this study. the fatigue behavior of cracked aluminum repaired by unidirectional graphite/epoxy composites was experimentally investigated. The aluminum used was 7075-T6 and the patch used was four plied unidirectional ([0]$_4$) composites. The composite patch was adhesively bonded to the cracked aluminum using secondary bonding procedure. Two different specimens of cracked aluminum and cracked aluminum repaired with patch were used in the fatigue tests. Load ratio and the frequency applied in the fatigue tests were 0 and 10 Hz, respectively. The results showed that the fatigue behavior of cracked aluminum was improved by repairing the cracked area with composite patch. Specifically, the specimen repaired by composite patch showed 30% more improved fatigue behavior than regular specimen.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.6
• /
• pp.637-643
• /
• 2011

The bond-based peridynamic model is able to capture many of the essential characteristics of dynamic brittle fracture observed in experiments: crack branching, crack-path instability, asymmetries of crack paths, successive branching, secondary cracking at right angles from existing crack surfaces, etc. In this paper we investigate the influence of the stress waves on the crack branching angle and the velocity profile. We observe that crack branching in peridynamics evolves as the phenomenology proposed by the experimental evidence: when a crack reaches a critical stage(macroscopically identified by its stress intensity factor) it splits into two or more branches, each propagating with the same speed as the parent crack, but with a much reduced process zone.

• Journal of Applied Biological Chemistry
• /
• v.44 no.2
• /
• pp.84-86
• /
• 2001

Capsaicin synthesis by suspension cultured cells of Jalapeno pepper (Capcicum annuum L.) was assessed in vitro under various conditions including temperature (23 and $30^{\circ}C$), light intensity (with light and without light), and shaking speed (110 and 200 rpm). Capsaicin production increased, while the cell biomass growth decreased possibly due to the production of a secondary metabolite. Capsaicin synthesis was primarily affected by light condition. Cells cultivated at 110 rpm and $23^{\circ}C$ under light condition yielded the highest fresh weight, while those cultivated under the same condition, but without light resulted in the lowest cell mass. Capsaicin content in cells of 18-day-old pepper grown at 110 rpm and $23^{\circ}C$ under light was 0.125% of the cell mass. However, without light treatment, the capsaicin content in cells at the same shaking speed and temperature increased up to 169%, indicating no light is favored in the capsaicin synthesis by Jalapeno pepper. Increasing the shaking speed from 110 to 200 rpm without light enhanced the capsaicin synthesis. Results of this study demonstrate that light condition is the limiting factor in the synthesis of capsaicin in tissue-cultured Jalapeno pepper cells.

• Polymer(Korea)
• /
• v.26 no.5
• /
• pp.599-606
• /
• 2002

In this study, 4,4'-tetraglycidyl diaminodiphenyl methane (TGDDM)/polyamideimide (PAI) blends were cured using diaminodiphenyl sulfone (DDS). And the effect of addition of different PAI contents to neat TGDDM was investigated in the thermal, mechanical, and morphological properties of the blends. The cure behavior and thermal stability of the cured specimens were monitored by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), respectively. Also, the critical stress intensity factor (K$\_$IC/) was measured in UTM, and the phase separation behavior and final morphology of TGDDM/PAI blends were examined in scanning electron microscopy(SEM). As a result, the cure temperature and cure activation energy (E$\_$a/) were decreased with increasing the PAI content. The decreasing of cure temperature and cure activation energy were probably due to the presence of secondary amine group of PAI backbone used as co-initiator. But, the decomposition activation energy (E$\_$t/) and K$\_$IC/ value were increased up to 5. 10 phr of PAI content, respectively and they were decreased above the PAI contents. These results were explained on the basis of chain scission reaction by etherification. And morphology of blends observed from SEM was confirmed in co-continuous structures.