• Journal of the Mineralogical Society of Korea
• /
• v.5 no.1
• /
• pp.32-41
• /
• 1992

An XRD quantitative analytical method using calculated XRD patterns was discussed in this study, Deep-seabed sediments commonly contain smectite, illite, chlorite, and kaolinite, and XRD pattern of each clay mineral of appropriate chemical composition was simulated by using an XRD pattern calculation method. Theoretical peak intensities of specific reflections of four clay minerals (the 001 reflections of smectite and illite, the 004 reflection of chlorite, and the 002 reflection of kaolinite) were measured from calculated patterns, and MIF(mineral intensity factor)value of each phase was determined from the intensities of calculated patterns. The peak intensities obtaine from experimental XRD patterns of sediments were corrected using the MIF values so that the calibrated intensity values for the specimens are linearly proportional to the weight fraction of each phase, which is normalized to 100 wt%. The MIF method can provide accurate quantitaive results without the necessity of correcting the factors by the mass absorption coefficient of each phase. This method excludes the necessity of standard specimens having compositions that are similar to those of clay minerals in the sediment samples. Therefore, quantitaive analysis using XRD calculation method can be utilized for the specimens, for which the standard specimens are very difficult or impossible to obtain. this quantitative method can provide rapid, routine analysis results for a large number of samples which occur in similar geological environments.

• Economic and Environmental Geology
• /
• v.48 no.5
• /
• pp.379-390
• /
• 2015

Multibeam backscatter strength is dependent not only on seafloor sediment facies but also on changed incidence angle due to the actual bottom slope. Therefore, the correction for actual bottom slope should be considered before the analysis of backscatter strength. This paper demonstrates the backscatter correction technique for the actual incidence angle and ensonified area. The target area is a part of the eastern Yellow Sea with water depths of 46~55 m. The area is located between the sand ridges and covered by large dunes with various bottom slopes. The dunes usually have the gentle slopes of about $1{\sim}3^{\circ}$, but show some steep slopes of $5{\sim}15^{\circ}$ on the crest. The backscatter strength values on the crest range from -34 to -23 dB, assuming that the bottom is flat. However, this study shows that the backscatter strength range was somewhat reduced (-32~-25 dB) after correction for actual bottom slope. In addition, the backscatter imagery was significantly improved; high and low backscatter strength values on the crest due to the actual bottom slope were normalized. The results demonstrate that the correction technique in this study is an effective tool for processing backscatter strength.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.12 no.3
• /
• pp.188-196
• /
• 2009

This study conducted numerical simulations to analyze the wave characteristics(distribution) depending on the directional changes of waves in the Nakdong river estuary by using SWAN(Simulating WAves Nearshore) model. The results from the tests are summarized as below. The wave height rates are generally highly distributed with the incident waves from the S, SSE, SSW, SE, SW in sequence. When the waves from the S, SSW, SSE directions are predominant, the bigger waves were observed in front of sandbars. According to the results of the wave steepness against the wave direction, at the east coast of Gadeok island(northwest of Nakdong estuary), where has mild seabed slopes, the wave height rates distribute in the range of 0.4~0.6; the wave height rates over the west coastal region of Dadeapo(southeast of Nakdong estuary) are 0.5~0.6. The wave height rate tends to be rapidly decreased over the east region of Nakdong river estuary rather than its west region.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.2
• /
• pp.95-103
• /
• 2013

An underwater acoustic (UWA) communication in shallow water is strongly affected by the water surface and the seabed acoustical properties. Every reflected signal to receiver experiences a time-variant scattering in sea surface roughness and a grazing-angle-dependent reflection loss in bottom. Consequently, the performance of UWA communication systems is degraded, and high-speed digital communication is disrupted. If there is a dominant signal path such as a direct path, the received signal is modeled statistically as Rice fading but if not, it is modeled as Rayleigh fading. However, it has been known to be very difficult to reproduce the statistical estimation by real experimental evaluation in the sea. To give an insight for this scattering and grazing-angle-dependent bottom reflection loss effect in UWA communication, authors conduct experiments to quantify these effects. The image is transmitted using binary frequency shift keying (BFSK) modulation. The quality of the received image is shown to be affected by water surface scattering and grazing-angle-dependent bottom reflection loss. The analysis is based on the transmitter to receiver range and the receiver depth dependent image quality and bit error rate (BER). The results show that the received image quality is highly dependent on the transmitter-receiver range and receiver depth which characterizes the channel coherence bandwidth.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.6
• /
• pp.713-719
• /
• 2001

The aim of this study is to check the application criteria of the conventional techniques and clarify the effects of breaker depth, seabed conditions on the stability in relation to the effects of uncertainty of storm duration and directional irregular waves. The typical damage modes were divided by the direct wave force on the armor unit and by the local scouring around the toe of a breakwater head by the model experiments. The destruction modes are defined, and some criteria on the damage modes and scouring/deposition at the toe of a breakwater head in relating the wave-bottom-structural conditions can be checked using the multi-directonal irregular wave generator system. According to the results, it is emphasized that the 3-D effects on the stability should be analyzed in the design of multi-purpose/function coastal structures in consideration of the evaluation of spatial variation of damage modes and hydraulic characteristics as well as the wave distribution along the structures.

• Journal of Navigation and Port Research
• /
• v.34 no.3
• /
• pp.195-203
• /
• 2010

This paper concerns about total dynamic analysis of integrated mining system. This system consists of vertical steel pipe, intermediate buffer station, flexible pipe and self-propelled miner. The self-propelled miner and buffer are assumed as rigid-body of 6-dof. Discrete models of vertical steel pipe and flexible pipe are adopted, which are obtained by means of lumped-parameter method. The motion of mining vessel is not considered. Instead, the motion of mining vessel is taken into account in form of various boundary conditions (e.g. forced excitation in slow motion and/or fast oscillation and so on). A terramechanics model of extremely cohesive soft soil is applied to the self-propelled miner. Hinged and ball constraints are used to define the connections between sub-systems (vertical steel pipe, buffer, flexible pipe, self-propelled miner). Equations of motion of the coupled model are derived with respect to the each local coordinates system. Four Euler parameters are used to express the orientations of the sub-systems. To solve the equations of motion of the total dynamic model, an incremental-iterative formulation is employed. Newmark-${\beta}$ method is used for time-domain integration. The total dynamic responses of integrated mining system are investigated.

• Ocean Systems Engineering
• /
• v.6 no.1
• /
• pp.23-60
• /
• 2016

The major objective of this study was to develop further understanding of 3D nearshore hydrodynamics under a variety of wave and tidal forcing conditions. The main tool used was a comprehensive 3D numerical model - combining the flow module of Delft3D with the WAVE solver of XBeach - of nearshore hydro- and morphodynamics that can simulate flow, sediment transport, and morphological evolution. Surf-swash zone hydrodynamics were modeled using the 3D Navier-Stokes equations, combined with various turbulence models (${\kappa}-{\varepsilon}$, ${\kappa}-L$, ATM and H-LES). Sediment transport and resulting foreshore profile changes were approximated using different sediment transport relations that consider both bed- and suspended-load transport of non-cohesive sediments. The numerical set-up was tested against field data, with good agreement found. Different numerical experiments under a range of bed characteristics and incident wave and tidal conditions were run to test the model's capability to reproduce 3D flow, wave propagation, sediment transport and morphodynamics in the nearshore at the field scale. The results were interpreted according to existing understanding of surf and swash zone processes. Our numerical experiments confirm that the angle between the crest line of the approaching wave and the shoreline defines the direction and strength of the longshore current, while the longshore current velocity varies across the nearshore zone. The model simulates the undertow, hydraulic cell and rip-current patterns generated by radiation stresses and longshore variability in wave heights. Numerical results show that a non-uniform seabed is crucial for generation of rip currents in the nearshore (when bed slope is uniform, rips are not generated). Increasing the wave height increases the peaks of eddy viscosity and TKE (turbulent kinetic energy), while increasing the tidal amplitude reduces these peaks. Wave and tide interaction has most striking effects on the foreshore profile with the formation of the intertidal bar. High values of eddy viscosity, TKE and wave set-up are spread offshore for coarser grain sizes. Beach profile steepness modifies the nearshore circulation pattern, significantly enhancing the vertical component of the flow. The local recirculation within the longshore current in the inshore region causes a transient offshore shift and strengthening of the longshore current. Overall, the analysis shows that, with reasonable hypotheses, it is possible to simulate the nearshore hydrodynamics subjected to oceanic forcing, consistent with existing understanding of this area. Part II of this work presents 3D nearshore morphodynamics induced by the tides and waves.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09c
• /
• pp.72-77
• /
• 2010

The Incheon Bridge, which was opened to the traffic in October 2009, is an 18.4 km long sea-crossing bridge connecting the Incheon International Airport with the expressway networks around the Seoul metropolitan area by way of Songdo District of Incheon City. This bridge is an integration of several special featured bridges and the major part of the bridge consists of cable-stayed spans. This marine cable-stayed bridge has a main span of 800 m wide to cross the vessel navigation channel in and out of the Incheon Port. In waterways where ship collision is anticipated, bridges shall be designed to resist ship impact forces, and/or, adequately protected by ship impact protection (SIP) systems. For the Incheon Bridge, large diameter circular dolphins as SIP were made at 44 locations of the both side of the main span around the piers of the cable-stayed bridge span. This world's largest dolphin-type SIP system protects the bridge against the collision with 100,000 DWT tanker navigating the channel with speed of 10 knots. Diameter of the dolphin is up to 25 m. Vessel collision risk was assessed by probability based analysis with AASHTO Method-II. The annual frequency of bridge collapse through the risk analysis for 71,370 cases of the impact scenario was less than $0.5{\times}10^{-4}$ and satisfies design requirements. The dolphin is the circular sheet pile structure filled with crushed rock and closed at the top with a robust concrete cap. The structural design was performed with numerical analyses of which constitutional model was verified by the physical model experiment using the geo-centrifugal testing equipment. 3D non-linear finite element models were used to analyze the structural response and energy-dissipating capability of dolphins which were deeply embedded in the seabed. The dolphin structure secures external stability and internal stability for ordinary loads such as wave and current pressure. Considering failure mechanism, stability assessment was performed for the strength limit state and service limit state of the dolphins. The friction angle of the crushed stone as a filling material was reduced to $38^{\circ}$ considering the possibility of contracting behavior as the impact.

• The Journal of Engineering Geology
• /
• v.24 no.1
• /
• pp.9-21
• /
• 2014

We examined high-resolution seismic data, side scan sonar data, surface sediments, and vibrocore samples from a sand ridge off the western part of Dukjuk-Do in Gyeonggi Bay, with the aim of interpretation of seismic stratigraphy and sedimentary environment. Based on the seismic data, the deposited sands are divided into three sedimentary units. 14C age data indicate that the top sequence (sequence I) formed at 5000-6000 yr BP, when a transgression resulted in strong shifting tides. Analyses of the vibrocore samples indicate that sequence II is a paleo-mudflat layer of intertidal sediments dominated by mud. Sequence III consists of terrestrial sediments that are presumed to have been deposited at the end of the Pleistocene, unconformably overlying the acoustic bedrock and Mesozoic granite. The side scan sonar data indicate that sand waves were formed on the seabed on top of the sand ridge. Generally, this is the direction of $N20^{\circ}E$, which coincides with the direction of tidal flow. Sand ripples occur away from the top of the sand ridge and are distributed homogeneously across a sandy slope. Vibrocore analyses indicate that the surface sediments and core sediments (samples VC-1, -2, and -3) are homogeneous, without any internal structures, and are characterized by a mixture of medium and fine sand (1-$2{\phi}$), respectively.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.8 no.4
• /
• pp.165-173
• /
• 2005

Field observations have been conducted to investigate the physical environment around oyster farms in Gamak Bay. Tidal waves near the two channels at the northeast and south of the bay had almost the same amplitudes and phases. Water temperature responded sensibly to the tides, rising at high water and falling at low water, except for the northwest region. The currents more regularly varied in accordance with a tidal period as long as they are at the faster-flowing region. A considerable flow has been found near the seabed of the northwest of the bay, normally known to be a stagnant area, and also the flow was opposite to the surface flow. Average moving speeds and directions of the flow at each station coincided well with patterns of the residual currents computed by Lee ef al. [2004], except for the northwest region. The discrepancy for the northwest region is not clear but it may have resulted from the facts that the computed flow pattern represents only the case of spring tide and in addition, a northwesterly wind prevailed all the observation time.