• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.73-76
• /
• 2009

ZnBo이 첨가된 (Ba,Sr)$TiO_3$ 후막을 이용한 planner capacitor의 전기적 특성을 조사하였다. 후막은 알루미나 기판에 스크린 프린팅기법에 의해서 제작되었고 $1200^{\circ}C$의 온도에서 소결하였다. 출발 물질인 BST의 저온 소결을 위해서 ZnBO를 첨가하였다. ZnBO가 1, 3, 5 wt% 첨가된 경우 소결온도가 $1200^{\circ}C$의 낮은 온도에서 소결되는 것을 확인했으며 ZnBO의 첨가랑이 증가함에 따라서 유전율은 감소하고 유전손실는 증가 하는 현상이 나타났다. 1, 3, 5 wt%의 ZnBO가 첨가된 (Ba,Sr)$TiO_3$는 각각 756, 624, 554의 유전율를 보였다. 또한 ZnBO의 양이 증가함에 따라서 누설전류가 감소되는 것을 확인하였고, ZnBO의 첨가가 grain의 성장과 density가 증가되어 누설전류의 양이 감소하게 되는 것으로 분석되었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.546-546
• /
• 2012

Traditional screen printing is still a dominant method to print electrodes on c-Si solar cells. In order to achieve higher efficiency for c-Si solar cells, improvement of the electrode material is one of the key approaches. Shadowing loss can be reduced by using high aspect ratio finger electrode with width of finger electrode less than 80um. The rheological properties of Ag paste for applying c-Si solar cells are improved by using Ag nanowires. The printing properties including the aspect ratio of printed electrode can be improved with higher Thixotropic index (T.I.) values.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1243-1244
• /
• 2006

In this paper, PZT(20/80) thick films were fabricated by the screen-printing method. And the PZT(80/20) coating solution was synthesized by the sol-gel method. PZT(20/80) thick films were screen-printed on the alumina substrates. PZT(80/20) thin film was spin-coated on the PZT(20/80) thick films to obtain densification. And the structural and electrical properties of PZT thick films were investigated with variation of sintering temperature. The PZT specimen sintered at $650^{\circ}C$ showed good relative dielectric constant of 219 and dielectric loss of 2.45%. Also the remanent polarization and the coercive field were $16.48{\mu}C/cm^2$ and 35.48kV/cm, respectively.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1245-1246
• /
• 2006

Ferroelectric PZT (70/30) thick films were fabricated by the screen printing method. And the PZT (30/70) precusor solution were infiltrated by the spin-coating method on the PZT thick films to obtain a densification. All PZT thick films were sintered at $1050^{\circ}C$ for 10 min. Structural properties, such as crystalline structure, microstructures and compositional ratio, of PZT thick films were investigated with the variation of the number of sol coatings using XRD, SEM and EDS, respectively. All PZT thick films exhibited a perovskite polycrystalline structure without a pyrochloer phase. The thickness of PZT thick films, 4-times screen-printed, was approximately $60{\mu}m$. And the densification of the PZT thick films increased with increasing the number of sol coatings.

• Journal of Sensor Science and Technology
• /
• v.16 no.6
• /
• pp.449-456
• /
• 2007

The work described in this study concerns the development of a disposable amperometric sensor for the electrochemical detection of a well-known aqueous pollutant, free available chlorine (FAC). The FAC sensor developed used screen printed carbon electrodes (SPCEs) coupled with immobilised syringaldazine, commonly used as an indicator in photometric FAC detection, which was directly immobilised on the surface of SPCEs using a photopolymer PVA-SbQ. To enable in-field analysis of FAC, a prototype hand-held electrochemical analyzer has been developed to withstand the environment with its rugged design and environmentally sealed connections; it operates from two PP3 (9 volt) batteries and is comparable in accuracy and sensitivity to commercial bench top systems. The sensitivity of the FAC sensor developed was $3.5{\;}nA{\mu}M^{-1}cm^{-2}$ and the detection limit for FAC was found to be $2.0{\;}{\mu}M$.

• Journal of the Korean Ceramic Society
• /
• v.30 no.12
• /
• pp.1007-1014
• /
• 1993

YBa2Cu3Ox(YBCO) thick films were prepared by a screen printing of the powders, obtained by a coprecipitation in oxalic acid, on the Y2O3-stabilized zirconia substrates and their superconducting properties were determined. TC, JC and the orientation factor of the thick films increased with increasing temperature up to 103$0^{\circ}C$ and then the superconducting properties disappeared with further heat treatments. The optimization of JC was achieved by heating thick films at 103$0^{\circ}C$ for 7min. In this case the TC of the thick film was determined to be 87.5K. It was observed that TC of thick films depends on the orthorhombicity and JC is likely governed by a microstructure of YBCO rather than by the orientation factor.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.691-692
• /
• 2009

Screen printable CNT pastes were formulated including conductive nano particles (CNPs) and their properties were investigated with an expectation of stable cold cathodes for advanced lamp application. CNT cathodes showed a turn-on field of 1~1.5V/um, a life time of ~100 hours at an emission current density of 10uA/$cm^2$ for DC-bias. Detailed analysis of measured I-V was carried out by applying Fowler-Nordheim model to trace down the origin of emission property degradation.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1703-1704
• /
• 2006

In this paper, PZT(20/80) thick films were fabricated by the screen-printing method. And the PZT(80/20) coating solution was synthesized by the sol-gel method. PZT(20/80) thick films were screen-printed on the alumina substrates. PZT(80/20) thin film was spin-coated on the PZT(20/80) thick films to obtain densification. And the structural and electrical properties of PZT thick films were investigated with variation of sintering temperature. The PZT specimen sintered at $650^{\circ}C$ showed good relative dielectric constant of 219 and dielectric loss of 2.45%. Also the remanent polarization and the coercive field were $16.48{\mu}C/cm^2$ and 35.48kV/cm, respectively.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1705-1706
• /
• 2006

Ferroelectric PZT (70/30) thick films were fabricated by the screen printing method. And the PZT (30/70) precusor solution were infiltrated by the spin-coating method on the PZT thick films to obtain a densification. All PZT thick films were sintered at $1050^{\circ}C$ for 10 min. Structural properties, such as crystalline structure, microstructures and compositional ratio, of PZT thick films were investigated with the variation of the number of sol coatings using XRD, SEM and EDS, respectively. All PZT thick films exhibited a perovskite polycrystalline structure without a pyrochloer phase. The thickness of PZT thick films, 4-times screen-printed, was approximately $60{\mu}m$. And the densification of the PZT thick films increased with increasing the number of sol coatings.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.182-182
• /
• 2009

일반적으로 스크린 프린팅 공정은 실비가 간단하고 공정이 쉬우며 가격이 저렴한 특성을 가지고 있다. 본 연구에서는 스크린 프린팅 방법들 이용하여 절연층을 코팅하고 도체 패턴을 형성하여 MCPCB(Metal-Core Printed Circuit Board) 기판을 제작하였다. 또한, 이 방법으로 제작된 MCPCB 기판의 방열 특성을 기존 상용 MCPCB와 비교 평가하였다.