• Journal of the Korean institute of surface engineering
• /
• v.35 no.3
• /
• pp.113-120
• /
• 2002

Injection molded plastic parts have many surface defects. These include a weld line, sink mark, flow mark, gloss, shading, scratching etc. Because these surface faults are not aesthetically acceptable, plastic parts are produced through painting or texturing. The purpose of this paper is to develop paintless molded parts using a flow control method. Computer aided injection mold filling simulations were used in order to minimize the number of defects from injection molding. Based on the numerical results, FR(Flame Retardant) HIPS was developed and the guidelines for part design, mold design, and the processing conditions were established. The effects of cost savings, improvements in productivity, and recycling were considered by reducing the number of surface faults and eliminating the painting process.

• Transactions of Materials Processing
• /
• v.25 no.3
• /
• pp.176-181
• /
• 2016

The exhaust tail pipe is the only visible part of the exhaust system on a vehicle. The conventional way to make the tail pipe is welding after stamping. There are various problems that occur during the stamping of stainless steel sheets such as scratching and local fracture. Problems during welding can also occur due to poor weldability. Tube hydroforming can be a solution, which eliminates these problems. The current study deals with the development of tube hydroforming for a vehicle tail pipe using finite element analysis for a free-feeding method. The current study focuses on the development of a proper load path for the tail pipe hydroforming and how bending influences the subsequent processing steps. The FE analysis results were compared with experimental results. This study shows the importance of bending and the necessity of considering bending when performing a tube hydroforming analysis.

• Transactions of Materials Processing
• /
• v.11 no.8
• /
• pp.691-700
• /
• 2002

Injection molded plastic parts have many surface detects: weld line, sink mark, flow mark, gloss, shading, scratching, and so on. Because these surface faults have not been accepted esthetically, plastic parts are Produced through painting or texturing. The purpose of this paper is to develop a paintless molded part of TV Mask Front by flow control method and gas-assisted injection molding. In order to minimize defects from injection molding, this study was carried out using computer aided injection mold filling simulations using MF/FLOW and MF/GAS. Based on these numerical results, we developed FR(Flame Retardant) HIPS and established guidelines of part design, mold design, and Processing conditions. We have achieved of cost sayings, improvement of productivity, and utilization of recycling by eliminating surface defects and painting process.

• Tribology and Lubricants
• /
• v.20 no.3
• /
• pp.125-131
• /
• 2004

Nano-wear behavior of amorphous carbon films was studied by Atomic Force Microscopy. The a-C films are deposited on Si(100) substrate by DC magnetron sputtering method. The influences of different surface roughness on the nano-wear are investigated. Nano-wear tests were carried out using a very sharp diamond coated tip. Its spring constant was 1.6 N/m and radius of curvature was 110 nm. Normal force used in the wear tests ranged 0 to 400 nN. It was found that surface depression occurred during scratching because of plastic deformation and abrasive wear (cutting St ploughing). Wear depth increased linearly with normal force. Changing the surface roughness variables according to the bias pulse control, the less surface roughness decreased the wear depth. The thickness did not affect the wear resistance.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.135-136
• /
• 2022

Defects caused by apartment houses have the term of warranty liability according to the enforcement ordinance of Acts of the Management of Apartment Houses. In case when defects occur during the term, free defect maintenance can be provided from the construction company. Yet, there occur conflicts between the construction company and residents, as to whether there occur defects or not. To resolve these conflicts, this study aimed to analyze construction classification and types that need managing, based on defects of apartment houses occurring during the term of warranty liability. This research analyzed 138,576 cases of data, as of five apartment house complexes. For the construction classification for defects of apartment houses, wooden flooring products accounted for the highest rate, followed by paper hanging, and wooden window. For the construction types of defects, torn/scratching took up with the highest rate, followed by the condition of defect in fixing and operating. In order to embody defects occurring during the term of warranty liability, into the visualization technique, this researcher utilized the word cloud method. This study will pursue the method for maintaining defects during the term of warranty liability, in the subsequent research, using the data that this research presented.

• Journal of Powder Materials
• /
• v.20 no.2
• /
• pp.120-124
• /
• 2013

This study is carried out to develop the new process for the fabrication of ultra-fine electrodes on the flexible substrates using superhydrophobic effect. A facile method was developed to form the ultra-fine trenches on the flexible substrates treated by plasma etching and to print the fine metal electrodes using conductive nano-ink. Various plasma etching conditions were investigated for the hydrophobic surface treatment of flexible polyimide (PI) films. The micro-trench on the hydrophobic PI film fabricated under optimized conditions was obtained by mechanical scratching, which gave the hydrophilic property only to the trench area. Finally, the patterning by selective deposition of ink materials was performed using the conductive silver nano-ink. The interface between the conductive nanoparticles and the flexible substrates were characterized by scanning electron microscope. The increase of the sintering temperature and metal concentration of ink caused the reduction of electrical resistance. The sintering temperature lower than $200^{\circ}C$ resulted in good interfacial bonding between Ag electrode and PI film substrate.

• The Korean Journal of Ceramics
• /
• v.3 no.2
• /
• pp.73-81
• /
• 1997

In this paper, it is intended to present more reproducible and quantitative method for adhesion assemssement. In scratch test, micromechanical analysis on the stress state beneath the indenter was carried out considering the additional blister field. The interface adhesion was quantified as work of adhesion through Griffith energy approach on the basis of the analyzed stress state. The work of adhesion for DLC film/WC-Co substrate calculated through the proposed analysis shows the identical value regardless of distinctly different critical loads measured with the change of film thickness and scratching speed. On the other hand, uniaxial loading was imposed on DCL film/Al substrate, developing the transverse film cracks perpendicular to loading direction. Since this film cracking behavior depends on the relative magnitude of adhesion strength to film fracture strength, the quantification of adhesion strength was given a trial through the micromechanical analysis of adhesion-dependence of film cracking patterns. The interface shear strength can be quantified from the measurement of strain $\varepsilon$s and crack spacing $\lambda$ at the cessation of film cracking.

• Transactions of Materials Processing
• /
• v.22 no.2
• /
• pp.86-92
• /
• 2013

When stamping ultra-high-strength steel (UHSS), the phenomenon of galling, which corresponds to a transfer of material from the sheet to the tool surface, occurs because of the high contact pressure between tool and workpiece. Galling leads to increased friction, unstable interface conditions, scratches on the sheet and the tool surfaces and, eventually, premature tool surface failures. Therefore, a simple and accurate evaluation method for tool scratching is necessary for the selection of tool material and coating, as well as for a better optimization of process conditions such as blank holder force and die radius. In this study, the pin-on-disc (PODT) and pin-on-flat surface (POFST) tests are conducted to quantitatively evaluate scratch-related tool life for stamping of UHSS. The variation of the friction coefficient is used as an indicator of scratch resulted from galling. The U-channel ironing test (UCIT) is performed in order to validate the results of the friction tests. This study shows that the POFST test provides a good quantitative estimation of tool life based on the occurrence of scratch.

• Journal of Veterinary Clinics
• /
• v.38 no.3
• /
• pp.147-151
• /
• 2021

A 5-year-old castrated male Maine Coon cat presented with chronic otitis on the right ear. The clinical signs, scratching and head shaking, were recurrent despite symptomatic treatment, including antibiotics and antifungal agents. Video otoscopic examination and computed tomography (CT) examination revealed a polyp in the right ear canal. The polyp was removed via per-endoscopic trans-tympanic traction (PTT) with a grasping forceps. After treatment, Horner's syndrome occurred in the right eye but spontaneously resolved a week later. The mass was diagnosed as inflammatory polyp with a fibrovascular stroma containing plasma cells, lymphocytes, and neutrophils. All clinical signs were improved, and no recurrence was observed after 3 weeks of follow-up. This case report demonstrates that CT scan is effective in identifying the margin of polyp and PTT technique is non-invasive method for treating inflammatory polyp in cats without severe complications.

• Journal of Korean Society of Forest Science
• /
• v.109 no.4
• /
• pp.400-412
• /
• 2020

We analyzed the growth characteristics of naturally regenerated seedings of Larix kaempferi in order to propose a field-applicable regeneration method. Experimental sites were established at Gapyeong in Gyeonggi-do and at Bonghwa in Gyeongsangbuk-do. We analyzed seed inflow features, occurrence, and growth characteristics of natural seedlings for three years. The reserved seed-tree site producedthe greatest number of inflow seeds and followed by seed-tree site and clear-cut site. In addition, the reserved seed-tree method was found to be more efficient than other methods in evenly scattering seeds. The rate of seedling occurrence at treatment sites (e.g., harvesting and scratching) was 2.4%, which is 8.0 times higher than the seedling occurrence (0.3%) at the non-treatment sites. There were approximately 470,000 seedlings per hectare at the treatment sites in June of the first year after regeneration and approximately 78,000 seedlings per hectare in October of the third year. The average diameter of the root collar of the seedlings in the third year was 6.5 mm, and the average height of the seedlings was 50.4 cm. These results indicate that it is possible to create a secondary forest of L. kaempferi by natural regeneration if harvesting and scraping are implemented during seed fructification. Considering the rapid growth of L. kaempferi shown in this study, the proposed method would be an efficient reforestation technique.