• 한국수학교육학회지시리즈A:수학교육
• /
• 제44권1호
• /
• pp.41-65
• /
• 2005

In this paper we make an experiment in order to test whether the teaching method with the Zone of Proximal Development (ZPD) developed by Vygotsky can be more effective and well applied in the middle school pratces. Based on this investigation, we conclude that ZPD help to efficiently enhance the study of students, in particular, the inferior student group. Moreover, if we divide the student by more precise stoups, the ZPD will be more effective on teaching and learning in middle school. Lastly, we arrive at the conclusion that a continuous teaching with ZPD will improve the student attitude positively in solving mathematical problem even it does not appeared apparently on this test.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.534-538
• /
• 2002

Dissimilar friction stir welding of aluminum (AI) alloy 1050 and magnesium (Mg) alloy AZ31 was successfully done in the limited welding parameters. The dissimilar weld showed good quality and facility compared to conventional fusion weld. Transverse cross section perpendicular to the welding direction had no defects. The weld was divided into base material of Al alloy, an irregular shaped stir zone and base material of Mg alloy. The irregular shaped stir zone was roughly located around the initial weld center. The weld interface near plate surface shifted from initial weld centerline to the advancing side. Hardness profile of the weld was heterogeneous, and the hardness value of the stir zone was raised to about 150 Hv to 250 Hv. The mixed phase was identified to intermetallic compound $Mg_{17}$Al$_{12}$ using x-ray diffraction method, energy dispersive x-ray spectroscopy (EDX) and electron probe micro analysis (EPMA). The formation of intermetallic compound $Mg_{17}$Al$_{12}$ during FSW causes the remarkable increase in hardness value in the stir zone.one.

• 한국도로학회논문집
• /
• 제14권6호
• /
• pp.93-101
• /
• 2012

PURPOSES : This study is to develop ISM for potential risk factor in School Zone. METHODS : Based on the literature review, the Analytic Hierarchy Process (AHP) has been used most widely. However, it is difficult to apply in practice because the AHP results have the characteristics of the independence between each element and the interlayer can not explain the interrelationship. The Network Analysis Process (ANP) is possible to analyze the relationship between the elements and the network through the feedback. But, the reliability of the analysis fall because of complicated pair of comparison, also it is difficult to solve the super matrix. In this study, the complicated relationship between each element is inquired through the Interpretive Structural Modeling (ISM). RESULTS : The methodology of ISM is developed to remove the children's potential risk factors in school zone. CONCLUSIONS : It is possible to remove the children's potential risk factors from low level to high level step by step and improve safety. Through this, risk factors can be removed from the low-level, and upper-level will automatically improve.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.331-334
• /
• 2006

This paper deals with the ways how the AUV is composed of sub-modules to be fault-tolerant during the mission. The emergency situations can be classified into several parts according to the zones where the situations take place - sensor zone, actuator zone, interpreter zone, and communication zone. This paper explains how each element of emergency situation is detected, contained and treated, and as a result, introduce the modular structured AUV controller for the autonomous cruising.

• 한국학교수학회논문집
• /
• 제14권4호
• /
• pp.519-538
• /
• 2011

이 연구는 방과 후 수업에서 근접발달영역을 고려한 수업이 중학교 1학년 학생들이 학생들의 학습태도와 문제해결력에 미치는 영향이 어떠한지를 알아보기 위하여 디자인 되었다. 연구문제를 해결하기 위하여 방화 후 수업에서 함수를 학습할 때 근접발달영역을 고려한 지도와 일반적인 수업을 받은 학생들에 대하여 학습태도와 문제해결력이 차이를 보이는지 알아보기 위하여 t-검정을 실시하였다. 검정 결과 방과 후 수업에서 근접발달영역을 고려한 수업이 학습태도와 문제해결력에서 유의미한 차이를 보였다.

• Restorative Dentistry and Endodontics
• /
• 제29권5호
• /
• pp.446-453
• /
• 2004

하악 대구치 근심치근의 danger zone에서 수종의 전동 니켈-티타늄 파일의 근관성형력을 근관성형 전후 치질 두께의 변화를 측정하여 평가하고자 하였다. 기구에 따라 총 40개의 하악 대구치를 10개씩 $Profile^{\circledR}$, GT Rotary file, Quantec 및 ProTaper 4개 군으로 나누고 각 치아당 2개의 근관을 straight up-and-down과 anticurvature 군으로 나누어 근단부 근관을 모두 30번 크기로 일정하게 확대하였다. 수정된 Bramante법을 사용하였으며 술전 및 술후의 근관 상아질 두께를 치수저 하방 1, 3 및 5 mm지점에서 측정, 이원변량분석법으로 통계분석하였다. 모든 군의 danger zone과 safe zone에서의 straight up-and-down 동작과 anticurvature 동작 사이에는 치근상아질 두께변화에 현저한 차이를 나타내지 않았다 (p > 0.05). ProTaper는 danger zone과 safe zone 모두에서 다른 기구에 비해 많은 량의 근관상아질 삭제를 보였으며 특히 분지부 3 mm 수준에서 현저하였다(p < 0.05).

• Journal of Welding and Joining
• /
• 제26권3호
• /
• pp.45-50
• /
• 2008

SM45C steel rods being used generally for power transmission shafts and machine components was selected and welded by Butt-GMAW(Gas Metal Arc Welding) method. An estimation of fatigue life was studied by constructing S-N curve. Fatigue strength of base metal zone showed higher values than one of weld zone in low cycles between $10^4$ and $10^6$cycles. However, significant decrease in fatigue strength of base metal was found around $10^6$cycles, which were almost same as one of heat affected zone. This decrease was attributed that initial residual stress of the steel rods distributed by drawing process was diminished by continually applied load, and resulted in softening of base metal. The fatigue limit of the weld zone was highest in the boundary between deposited metal zone and heat affected zone, and followed by in the order of deposited metal zone, base metal zone, and heat affected zone. Based on these results, it is revealed that the stress for safety design of machine components using SM45C butt-welded steel rods must be selected within the region of the lowest fatigue limit of heat affected zone.

• 설비공학논문집
• /
• 제17권8호
• /
• pp.722-728
• /
• 2005

The present paper deals with heating energy estimation in Korean-style apartments, paying special attention to the effect of room condition settings. Two types of heating modes are considered: continuous single-zone and scheduled multi-zone. In the latter, zones during unoccupied periods remain unconditioned. Also analyzed are sensitivities in heating energy with respect to the air change rate and the set temperature. The energy use is estimated with TRNSYS 15, a dynamic load calculation program. Heating energy for the actual residential condition (1.0 ACH and $24^{\circ}C$) appears to be nearly the same as that for a typical design standard (1.5 ACH and $20^{\circ}C$). The air change rate affects heating energy as sensitive]y as the set temperature. For all the simulated cases, the scheduled multi-zone heating mode is more energy-efficient than the continuous single-zone. Heating energy depends appreciably on the shading factor. It is expected that considerable heating energy for apartment houses can be saved by employing a multi-zone mode along with appropriate control devices.

• 대한기계학회논문집A
• /
• 제26권3호
• /
• pp.528-536
• /
• 2002

As one step for the safety performance of LNG storage tank, the change in fracture toughness within the X-grooved weld heat-affected zone (HAZ) of newly developed 9% Ni steel, which was submerged arc (SA)-welded, was investigated. Both crack initiation fracture toughness and crack arrest fracture toughness were evaluated by the crack tip opening displacement (CTOD) tests and compact crack arrest (CCA) tests. As the evaluated region approached the fusion line, each test result shorted different tendency, that is, crack initiation toughness decreased while crack arrest toughness increased. The results were discussed through the observation of the microstructural change.

• 산업공학
• /
• 제24권4호
• /
• pp.341-350
• /
• 2011

This paper considers a problem of locating both distribution centers and retailers in a zone-dependent two-level distribution network where either a distribution center or a retailer should be located in each zone. Customer demands of each zone should be satisfied directly from either its own distribution center or its own retailer being supplied from a distribution center of another zone. The objective of the proposed problem is to minimize total cost being composed of distribution center/retailer setup costs and transportation costs. In the analysis, the problem is proved to be NP-hard, so that a branch-and-bound algorithm is derived for the problem. Numerical experiments show that the proposed branch-and-bound algorithm provides the optimal solution efficiently for some small problems.