• Journal of the Korean Solar Energy Society
• /
• v.32 no.6
• /
• pp.11-21
• /
• 2012

In the normal office building, the energy consumption to maintain the reasonable intensity of illumination for the work by using the artificial illumination occupies 30% or greater of the whole building electric energy consumption. If the dependability of the artificial illumination is dropt by positively using the natural lighting from the outside, the large amount of electrical energy can be saved, in addition the more nice visual environment for work can be created. Daylight is lighting source that most closely match visual response of the human, because sunlight and skylight achieve the harmony. For this reason, the daylight of small amount than amount of the artificial lighting source also can give the same effect in work activities of human. In addition, if there is daylight at the window of the building, the energy can be saved by controlling the artificial lighting. In this paper, in the building using the photovoltaic power generation analyze the correlation between the amount of energy generated by photovoltaic and indoor illumination and this was proved through the simulation with Relux 2010. In addition, the amount of daylight inflow in the room and distribution was drawn by the equation and the ratio for the sectional dimming control of each lighting equipment was predicted and the energy saving amount according to this was calculated. As a result, the indoor illumination was satisfied with recommended illumination value of the office and consumption power could be reduced approximately with 20~70%.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.40 no.4
• /
• pp.129-136
• /
• 2017

Climate change is the biggest environmental issue of our times. A variety of activities to reduce greenhouse gas emissions have been in progress to observe the Kyoto Protocol. Especially, the Energy Target Scheme is created to reduce greenhouse emission with the supervision of Korean government. This includes Green-house Gas Information Systems to promote activities in the private sector to reduce green-house gas emissions, to cut a cost of energy use, and to reduce GHG emissions. Also, the system has calculated the amount of greenhouse gases. Without any additional investment, 2.75% savings are increased over the previous year. In service sector, a cooperation of customers and employees is necessary. A reduction of GHG emissions requires a proper service organization, considering an amount of investment and payback period. Without any additional investment or replacement, employees can save energy easily turning off ventilation systems an hour before employees' departure, installing timers to turn off water purifiers and vending machines after some period of no use. The Green-house Gas Information System is similar to that of Environmental Management System. However, the Excel is the best program to calculate an amount of green-house gas emissions, and to assess for a reduced amount of GHG emissions. A goal of this research is to propose a practical method in the private sector to calculate an amount of green-house gases. The Green-house gas Information System based on Excel spreadsheet gives standards for good evaluation. The greenhouse gas information system establishes and executes the policies and objectives related to greenhouse gas emissions Similar to ISO 14001 environment management system structures, the advantages of using simplified Excel Sheet for calculating GHG emissions and reducing GHG emissions are easy to access.

• Nuclear Engineering and Technology
• /
• v.54 no.9
• /
• pp.3242-3249
• /
• 2022

As Kori unit 1 is undergoing the decommissioning process, estimating the disposal amount of waste from the decommissioned nuclear reactor has become one of the challenging issues. Since the waste disposal amount estimation depends on the packing of the waste, it is highly desirable to optimize the waste packing plan. In this study, we developed an efficient scheme for packing waste component segments. The scheme consists of 1) preparing three-dimensional models of segments, 2) orienting each segment in such a way to minimize the bounding box volume, and 3) applying hybrid genetic algorithm to pack the segments in the disposal containers. When the packing solution converges in the algorithm, it comes up with the number of containers used and the placement of segments in each container. The scheme was applied to Kori-1 reactor pressure vessel. The required number of containers calculated by the developed scheme was 24 compared to 42 that was the estimation of the prior packing plan, resulting in disposal volume savings by more than 40%. The developed method is flexible for applications to various packing problems with waste segments from different cutting options and different sizes of containers.

• Journal of Environmental Science International
• /
• v.32 no.6
• /
• pp.477-482
• /
• 2023

Halloysite nanotube (HNT) has a nanotube structure with the chemical formula of Al₂Si₂O₅(OH)₄ · nH₂O and is a natural sediment of aluminosilicate. A lot of research has been conducted to improve the mechanical properties of epoxy composites by generating interactions between HNTs and polymers through surface treatment of HNTs, such as exchange of amine group as a terminal functional group. However, most of the surface modification methods are performed under wet conditions, which require a relatively large amount of time, manpower and solvent. In order to save time and simplify complicated procedures, a dry coating machine was designed and used for amine group exchange. Comparing the XPS results, it was found that the results of NH₂-HNT prepared using a dry coating machine and the substitution through the wet method were not significantly different, and it has been confirmed that the amount of solvent used and the time savings can be made.

• Fashion & Textile Research Journal
• /
• v.25 no.6
• /
• pp.673-689
• /
• 2023

To realize the traceability of sustainable textile products, this study presents a low-carbon process through energy savings in the textile material manufacturing process. Traceability is becoming an important element of Life Cycle Assessment (LCA), which confirms the eco-friendliness of textile products as well as supply chain information. Textile products with complex manufacturing processes require traceability of each step of the process to calculate carbon emissions and power usage. Additionally, an understanding of the characteristics of the product planning-manufacturing-distribution process and an overall understanding of carbon emissions sources are required. Energy use in the textile material manufacturing stage produces the largest amount of carbon dioxide, and the amount of carbon emitted from processes such as dyeing, weaving and knitting can be calculated. Energy saving methods include efficiency improvement and energy recycling, and carbon dioxide emissions can be reduced through waste heat recovery, sensor-based smart systems, and replacement of old facilities. In the dyeing process, which uses a considerable amount of heat energy, LNG, steam can be saved by using "heat exchangers," "condensate management traps," and "tenter exhaust fan controllers." In weaving and knitting processes, which use a considerable amount of electrical energy, about 10- 20% of energy can be saved by using old compressors and motors.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.3
• /
• pp.297-308
• /
• 2017

One of the major engine thermal management system(TMS) strategies for improving fuel economy is to operate the engine in high temperatures. Therefore, this work performed a numerical and experimental study to examine the effect of several different STOs(Starting Temperature of Opening) of wax-thermostat, ranging from $85^{\circ}C$ to $105^{\circ}C$, of gasoline engine on fuel economy and emission characteristics. In this study, a gasoline car equipped with waxthermostat was tested and simulated under FTP-75 and HWFET mode. CRUISE $M^{TM}$ was used to simulate vehicle dynamics, transient engine performance and TMS. The test results showed fuel savings for both drive cycles due to higher STO of $100^{\circ}C$, which is slightly worse than that of $90^{\circ}C$ and amounts between 0.34 and 0.475 %. These controversial results are attributed to experimental errors and uncertainty. The computational results for three STOs, $85^{\circ}C$, $95^{\circ}C$ and $105^{\circ}C$, showed that fuel savings attributed to the application of higher STOs of $95^{\circ}C$ and $105^{\circ}C$ are relatively small and range from 0.306 to 0.363 %. It is also found that the amount of HC and CO emissions from the tailpipe tends to decrease with higher engine coolant temperature because of faster catalyst light-off and improved combustion.

• Journal of Labour Economics
• /
• v.27 no.1
• /
• pp.77-105
• /
• 2004

Given the limitations of UI benefit and self-insurance through precautionary savings, this paper suggests a new scheme of income support for the unemployed, which offers unemployed workers not only UI benefit but also borrowings from their future pension incomes. Allowing individuals to have effective self-insurance through pension- borrowing, this scheme provides them with consumption-smoothing and reduction in risk burden while maintaining search incentives of the unemployed. Simulation study based upon household panel data in Korea suggests that a heavy reliance should be set upon self-insurance through pension-borrowings rather than upon UI benefit, even for the low-income individuals who are subsidized under UI system. This result provides us with insightful implications for a social safety net in (fast-growing) developing countries, where people cannot afford a good amount of UI benefit or of precautionary savings against unemployment although they expect their incomes to be much higher in the future. Indeed, it is consumption-smoothing effect of self-insurance through pension- borrowings, as well as its incentive-maintaining effect, that makes it a promising alternative of social safety net in developing countries.

• Journal of Families and Better Life
• /
• v.20 no.6
• /
• pp.81-93
• /
• 2002

The purpose of this study is to analyze the effects of household income drops on household economic status during economic crisis periods. Using the data taken from Korean Household Panel Study for 1996 and 1998, it was investigated how household income change affected household income, expenditure, and assets/debt. The economic status change of the income-decreased group was compared with that of the income-increased group. The major findings were as follows: Average income of the total sample was 1,905 thousand won in 1996, while 1,419 thousand won in 1998. The household of which income was decreased during the period was 65.1% of total sample. Average income of the group was reduced from 2,263 thousand won to 1,239 thousand won. Among income sources, the amount of income from real asset was found to be the highest decreasing rate, and the amounts of both business and employed-work income were reduced almost up to an half of those in two years ago. The amounts for all expenditure categories were also decreased with decreasing household income. Especially the expenditures for food away from home, leisure, durable, recreation, and vehicle-related expense were found to have the highest income elasticity. The households with decreased income were found to reduce household expenditures by 377 thousand won per month, which was 70.9% of that in 1996. Decreases in household income resulted in decreases in net wealth by 10,170 thousand won. With decreases in household income, the amounts of total insurance and private savings such as gye were decreased, and so were the amounts of real assets and monetary assets.

• The Journal of the Korea Contents Association
• /
• v.19 no.10
• /
• pp.667-676
• /
• 2019

The purpose of this study was to assess the impact of childbirth on socioeconomic status changes of women. Data were collected from Korean Health Panel (2008-2015). A difference-in-differences model with propensity score matching was applied to assess the impact of childbirth on socioeconomic status changes. As a result, variables showing significant differences in the interaction terms indicating the impact of birth were the savings, economic activity, and occupational status. The impact of birth were significant in decreasing the amount of savings and negatively affecting women's economic activities, but in increasing the probability of full-time and regular employees in occupational status. Childbirth appears to have a negative impact on the home economics and socioeconomic status of women. The belief that home economies can be stabilized even after childbirth should be established, and a long-term and sustained support plan should be set up to realize this belief.

• Steel and Composite Structures
• /
• v.14 no.1
• /
• pp.21-39
• /
• 2013

The paper presents a numerical investigation, done with the computer program SAFIR, in order to obtain simpler finite element models for representing the behaviour of the partially protected composite steel concrete slabs in fire situations, considering the membrane action. Appropriate understanding and modelling of the particular behaviour of composite slabs allows a safe approach, but also substantial savings on the thermal insulation that has to be applied on the underlying steel structure. The influence of some critical parameters on the behaviour and fire resistance of composite slabs such as the amount of reinforcing steel, the thickness of the slab and the edge conditions is also highlighted. The results of the numerical analyses are compared with the results of three full scale fire tests on composite slabs that have been performed in recent years.