• Journal of the Society of Disaster Information
• /
• v.11 no.3
• /
• pp.318-328
• /
• 2015

Effective urban flood reduction and restoration of natural water cycle at present include the application of permeable pavements. The application of permeable pavement addresses urban water cycle and disaster related events which gained attention internationally. However, few researches have been conducted to investigate unsaturated behavior and evaluate the water characteristics curves of these type of pavement materials most especially in the unsaturated state. In this study, first the saturated permeability and the soil-water characteristics curve of a pervious concrete are evaluated based on laboratory tests, and, based on experimental results, the infiltration of permeable pavement system is numerically modelled. In the soil-water characteristics curve of a pervious concrete, the volumetric water content drops very steeply after the air entry value with increasing matric suction. From the finite element analyses, the performance of the permeable pavement when compared to impermeable pavement, confirmed that the whole system effectively delayed and reduced runoff.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.3
• /
• pp.87-95
• /
• 2020

As an experimental study on the corrosion behavior of steel materials to which ATMS method using EIS was applied in concrete, immersion of Ca(OH)₂ saturated aqueous solution and NaCl aqueous solution simulating the environment inside concrete The corrosion behavior was tested. The equivalent circuit was derived through the analysis of the Nyquist plot, and the interfacial resistance and the polarization resistance of the Ca(OH)₂ aqueous solution were compared, and Al ATMS was the best interfacial resistance and Zn ATMS was the best polarization resistance. After burying ATMS steel material of cement mortar, the initial immersion impedance measurement value was the highest in the Zn ATMS test body in the impedance measurement by the immersion time by immersing it in the NaCl aqueous solution. Al ATMS test piece has the highest impedance and is highly reliable. This is because Al, which has a high ionization tendency, is continuously oxidized in a strong alkaline environment to form a film and protect the steel from permeation of chlorine ions.

• Journal of the Korean Chemical Society
• /
• v.55 no.3
• /
• pp.509-518
• /
• 2011

In this study, we investigated the effects of analogy-generating in small group in elementary science-gifted education upon the types and the mapping errors of student-generated analogies, and the perceptions of the instruction. Fifth graders (N=37) at two science-gifted classes in two elementary schools were selected and assigned to individualistic analogygenerating (IA, n=19) and pair analogy-generating (PA, n=18) groups. After the students of each group performed the experiment and were taught about 'saturated solution' concept in the first class, they administered the test on the self-generating analogies on the concept in the second class. The students in the PA group also administered the test on perceptions of analogy-generating in small group and some of them were interviewed deeply. The results revealed that the students in the PA group made more verbal/pictorial, structural/functional, enriched, and higher systematic analogies than those in the IA group. However, there were little difference between the two groups in the subcategories of artificiality (artificial and everyday) and abstraction (abstract and concrete). The students in the PA group fewer mapping errors than those in the IA group. Many students in PA group perceived the analogy-generating in small group positively upon various cognitive and motivational aspects. However, they also pointed a few disadvantages of the activity. Educational implications of these findings are discussed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.3
• /
• pp.19-26
• /
• 2017

Concrete is a construction material with porous media and corroded steel inside affects negatively to durability and structural safety. This study aims a derivation of quantitative relationship between measured HCP (Half Cell Potential) and corrosion amount considering cover depth and W/C (water to cement) ratio. For the work, cement mortar specimens with 3 different W/C ratios and 4 different cover depths are prepared, HCPs are measured with 3 different corrosion level. HCP measurement significantly increases in the saturated condition and linear relationship is observed between corrosion level and acceleration period. With increasing corrosion level and W/C ratio, and decreasing cover depth, HCP measurement increases. Considering total corrosion level and HCP measurements, relatively low COV(Coefficient of Variation) of 0.67 is evaluated through multi-linear regression analysis, however higher COVs over 0.90 can be obtained considering level of HCP measurement. In the room condition, corrosion level can be evaluated through measured HCP in the given conditions of cover depth, W/C ratio. diameter of steel inside.

• Journal of the Mineralogical Society of Korea
• /
• v.23 no.1
• /
• pp.51-61
• /
• 2010

Ettringite $(Ca_6[Al(OH)_6]_2(SO_4)_3{\cdot}26H_2O)$ is a sulfate mineral that shows a complicate property in concrete. It is often called as "a cancer of concrete" because secondary ettringite formation in hardened concrete often cause expansion and cracking of concrete due to its expansive crystal structure. In the present study, we tested the possibility for crystal growth inhibition of secondary ettringite by crystallization inhibitors that are commercially used for scaling inhibitors in Korea. For the test, we developed a method of ettringite solution synthesis. Three types of crystallization inhibitors were selected and examined the effects On ettringite growth inhibition. The experimental results of ettringite solution synthesis indicated that ettringite was successfully synthesized under condition that the mass balance between calcium hydroxide saturated solution and aluminum sulfate solution was attained. Monosulfate and semisulfate were synthesized when the ratio of $Ca^{2+}$ ions to ${SO_4}^{2+}$ ions was increased. The induction time of ettringite crystallization was less than 2 min. and crystallization was almost completed within an hour. The experimental results of ettringite crystallization inhibition showed that organic PBCT (2-Phosphonobutane-1,2,4-Tricarboxylic Acid) and inorganic SHMP (Sodium Hexametaphosphate) were relatively less effective on ettringite crystallization inhibition under experimental conditions. However, organic HEDP (1-Hydoxyethylidene-1,1-Diphosphonic Acid) effectively prevented ettringite growth with producing amorphous gel phase materials up to inhibitor concentration 0.1 vol.% of aluminum sulfate solution.

• The Korean Journal of Physiology
• /
• v.1 no.1
• /
• pp.67-72
• /
• 1967

Present paper is attempted to introduce the phenomenon of 'after contraction' in isolated cardiac-muscle. Papillary muscles were removed from cat right ventricle and were used as a preparation. The muscle strip was Placed in tissue bath which is kept in steady temperature of around $25^{\circ}C$ and was perfuced by Tyrode solution, saturated with 95% $O_2$ and 5% $CO_2.$ under the condition of high calcium (8.2-10.0 mM/l), low sodium (72.4-70.0 mM/l) perfusion with the administration of epinephrine (1-2 mg/l) into tile tissue bath normally triggered muscle contraction was followed by oscillatory, repetitive contractions - after contraction. The phenomenon of after contraction was augumented by decrease in tissue bath temperature and by increase in number of preceding beats and in driving rate. Authors were able to maintain the phenomenon in prominent and steady state giving proper experimental conditions such as fixed bath temperature (ranged from $22^{\circ}C\;to\;27^{\circ}C$), suitable driving rate (20 per minute in average) and perfusion of high calcium, loll sodium and 1-2 mg/l of epinephrine. In some preparations, the strength of after contraction (second contraction) reached up-to 80% of normally triggered contraction and five repetitive contractions were observed as largest number of after contractions. Intracellular action potential measured in the muscle which was beating regulary showing steady after contraction revealed no oscillating after potential in most parts of the muscle but in few cases oscillating changes of after potentials were detectable. In electrogram of the muscle preparation recorded by means of contact electrode prominent, oscillating after potentials were observable when the recorder was set at highest sensitivity. It still is not clear that whether after contraction is the phenomenon which corresponds to those changes in action potential, oscillating after potential, of the muscle preparation. Possible mechanism of the phenomenon of after contraction relating with after potential changes was proposed. Detailed results obtained from further studies on after contraction and concrete discussion on the phenomenon will be reported by authors.

• Computers and Concrete
• /
• v.30 no.5
• /
• pp.339-355
• /
• 2022

The high cost of ultra-high-performance engineered cementitious composite (UHP-ECC) is currently a crucial issue, especially in terms of the polyethylene (PE) fibers use. In this paper, cheap calcium carbonate whiskers (CW) were evaluated on the feasibility of hybrid with PE fibers. Diverse combinations of PE fibers and CW were employed to investigate the multi-scale enhancement on the UHP-ECC performance. A probabilistic-based UHP-ECC tensile strain reliability analysis approach was utilized, which was in general agreement with the experimental results. Furthermore, a multi-dimensional integrated representation was conducted for the comprehensive assessment of UHP-ECC. Results illustrated that CW improved the compressive strength and energy dissipation capacity of UHP-ECC owing to the microscopic strengthening mechanism. CW and PE fiber further promoted the saturated cracking of composite by multi-scale crack arresting effect. In particular, PE1.75-CW0.5 specimen possessed the best overall performance. The ultimate cracking width of PE1.75-CW0.5 group had 98 ㎛, which was 46.18% lower compared to PE2-CW0 group, the 28d compressive strength were slightly improved, the tensile strain capacity was comparable to that of PE2-CW0 group. The results above demonstrated that combinations of PE fiber and CW could significantly enhance the comprehensive performance of UHP-ECC, which was beneficial for large-scale engineering applications.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.4
• /
• pp.419-434
• /
• 2020

In this study, the damage parameters of Mazars model for KURT (KAERI Underground Research Tunnel) granite are measured form uniaxial compressive and Brazilian tests under the simulated coupled condition of a deep geological disposal. The tests are conducted in three different temperatures (15℃, 45℃, and 75℃) and dry/saturated conditions. Major model parameters such as maximum effective tensile strain (𝜖_d0), A_t, B_t, A_c, and B_c differ from the typical reference values of concrete specimens. This is likely due to the difference in elastic modulus between rock and concrete. It is found that the saturation of specimens causes an increase in value of B_t and B_c while, the rise in temperature increases 𝜖_d0 and B_t and decreases B_c. The damage model obtained from this study will be used as the primary input parameters in the development of coupled Thermo-Hydro-Mechanical Damage numerical model in KAERI.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.5
• /
• pp.591-610
• /
• 2020

Concrete with activated carbon and titanium dioxide (TiO₂) has been used to reduce the particulate matter (PM) in underground structures (e.g., tunnels) due to the high performance of nitrogen oxides (NOx) abatement. Damage (e.g. crack, spalling, or detachment) can be caused by the environmental and ageing effects on the surface of the particulate matter reduction concrete, installed on the tunnel lining. Therefore, it is important to evaluate the existence of spalling on the concrete surface for maintaining performance of NOx reduction. In this study, a basic research was performed for feasibility of spalling evaluation using electrical resistivity characteristics. Given the test results, the electrical resistivity was decreased as the ratios of activated carbon (0~15%) and TiO₂ (0~25%) were increased for specimens. Under a dry condition, electrical resistivity of cement specimens, mixed with activated carbon and TiO₂, was decreased up to 2.3 times, compared with the normal cement specimen. In addition, under saturation conditions (degree of saturation: 85~98%), electrical resistivity of cement specimens with activated carbon, was decreased up to 3.5 times, compared with the normal cement specimen. Regardless of the condition (dry or saturated), the difference of electrical resistivity values shows the range of 2.3~2.8 times between the mixing specimen (with activated carbon (15%) and TiO₂ (25%)) and the normal cement specimen. This study can help to provide basic knowledge for spalling evaluation using the electrical resistivity on the surface of the particulate matter reduction concrete in tunnels.

• Journal of Distribution Science
• /
• v.11 no.10
• /
• pp.17-25
• /
• 2013

Purpose - This study analyzes the effect of customers' perceived service innovativeness of service centers for electronic goods, on repurchase intentions of customers, using behavior intentions of service centers as a mediator variable. In customer management and customer relationship marketing, service centers can be the most representative customer relationship management departments because they are most closely placed at the interface with customers. In addition, this study intends to investigate if continuous relationship with customers during one-time product-selling can affect their repurchase intentions. Specifically, this research aims to investigate if the expansion of the saturated physical market of the manufacturing business, to intangible service markets, can be competitive enough to satisfy customer needs. Research design, data, and methodology - This study targets college students, and especially those who have computers, digital cameras, or cell-phones, and often use electronic products and services. In order to investigate our hypothesis, we analyzed dates through SEM (structural equation modeling) using SPSS for Windows 18.0 and AMOS 18.0. In addition, we measured Cronbach's α coefficient using SPSS for Windows 18.0 in order to measure reliability. Further, using AMOS 18.0, this research statistically measured convergent validity as well as discriminant validity, and examined mediation models and path models in which service innovativeness leads to customers' repurchase intentions of electronic products. Results - As a result, this research shows that customers' perceived service innovativeness of service centers for electronic goods has significant positive influence on customers' behavior intentions of service centers. In addition, service innovativeness of electronic goods' service centers also has significant positive influence on repurchase intentions of customers. Conclusion - This study investigates the effect of customers' positive relation with the innovativeness of electronic service center on their behavior intention and product repurchase. The more concrete, important results of the study are as follows. Through the mediating effect, the findings of the study suggest that customers' behavior intentions of service centers partially mediate the effect of customers'perceived service innovativeness of service centers for electronic goods on customers' repurchase intentions. This research also provides an insight that the importance of service innovativeness and innovative approaches in managing customers should be recognized in the process of repurchase and service roles of manufacturing business as a way for customer management. As a result, the relationship between customer satisfaction and service quality of service centers for the electronic products is very sensitive. Although previous studies focus on certain aspects of the case for enhancing service innovation (Kim, 2012), this research recommends that the service centers need to understand the customers'desire first and try to adapt to achieve customer satisfaction by being innovative. This innovativeness of service centers would make customers visit them consistently, which in the long run, will also influence their repurchase decisions.