• The Journal of Advanced Prosthodontics
• /
• 제7권3호
• /
• pp.214-223
• /
• 2015

PURPOSE. To measure the surface loss of dental restorative zirconia and the short-term bond strength between an indirect composite resin (ICR) and zirconia ceramic after various sandblasting processes. MATERIALS AND METHODS. Three hundred zirconia bars were randomly divided into 25 groups according to the type of sandblasting performed with pressures of 0.1, 0.2, 0.4 and 0.6 MPa, sandblasting times of 7, 14 and 21 seconds, and alumina powder sizes of 50 and $110{\mu}m$. The control group did not receive sandblasting. The volume loss and height loss on zirconia surface after sandblasting and the shear bond strength (SBS) between the sandblasted zirconia and ICR after 24-h immersion were measured for each group using multivariate analysis of variance (ANOVA) and Least Significance Difference (LSD) test (${\alpha}$=.05). After sandblasting, the failure modes of the ICR/zirconia surfaces were observed using scanning electron microscopy. RESULTS. The volume loss and height loss were increased with higher sandblasting pressure and longer sandblasting treatment, but they decreased with larger powder size. SBS was significantly increased by increasing the sandblasting time from 7 seconds to 14 seconds and from 14 seconds to 21 seconds, as well as increasing the size of alumina powder from $50{\mu}m$ to $110{\mu}m$. SBS was significantly increased from 0.1 MPa to 0.2 MPa according to the size of alumina powder. However, the SBSs were not significantly different with the sandblasting pressure of 0.2, 0.4 and 0.6 MPa. The possibilities of the combination of both adhesive failure and cohesive failure within the ICR were higher with the increases in bonding strength. CONCLUSION. Based on the findings of this study, sandblasting with alumina particles at 0.2 MPa, 21 seconds and the powder size of $110{\mu}m$ is recommended for dental applications to improve the bonding between zirconia core and ICR.

• Restorative Dentistry and Endodontics
• /
• 제25권3호
• /
• pp.399-406
• /
• 2000

광중합형 글래스아이오노머 베이스에 대한 레진 인레이의 접착성을 증가시킬 수 있는 방법을 모색하고자, 이차 중합된 레진 인레이의 내표면을 여러 가지 방법으로 처리한 후 레진 인레이를 광중합형 글래스아이오노머 베이스에 레진 시멘트 접착시 내표면 처리방법이 이들의 접착에 미치는 영향을 평가하고자 하였다. 글래스아이오노머 베이스 제작을 위해서 플라스틱 봉에 직경 7mm, 깊이 2mm의 1급 와동을 형성하고 Fuji II LC를 충전하였으며, 수복용 레진(Charisma$^{(R)}$)을 사용하여 레진 인레이를 제작하였다. 레진 인레이 내면은 $50{\mu}m$ aluminum oxide particles를 이용한 sandblasting 및 silane 처리군, silane 처리군, sandblasting 군, 그리고 무처리 대조군 등 4군으로 나누어 표면처리하였으며 각 군은 22개씩의 시편을 사용하였다. 인레이와 베이스의 표면에 상아질 접착제(One-Step$^{TM}$)를 도포한 후 Choice$^{TM}$를 사용하여 레진시멘트 접착하였다. 접착 양상 평가를 위해 만능시험기로 전단접착강도를 측정하고 파단면을 입체현미경으로 관찰하여 다음과 같은 결과를 얻었다. 1. Sandblasting 및 silane 처리군이 가장 높은 접착강도(10.56${\pm}$1.95MPa)를 나타내었으며, 이는 sandblasting군 및 무처리 대조군에 비해 유의하게 높았다(p<0.05). 2. Silane 처리군(9.77${\pm}$2.04MPa)은 sandblasting 및 silane 처리군과는 접착력에 있어서 통계적으로 유의한 차이를 나타내지 않았으나, sandblasting 군 및 무처리 대조군에 벼해서는 유의하게 높은 접착강도를 나타내었다(p<0.05). 3. Sandblasting만 시행 한 군은 무처리 대조군과 비교시 접착강도에 있어 유의한 차이를 나타내지 않았다(p>0.05). 4. 파단면 관찰 결과, 모든 군에서 일부 접착계면에서의 파절을 포함하는 글래스아이오노머 베이스의 응집 파괴(cohesive failure) 양상이 가장 많이 나타났으며, sandblasting 및 silane 처리군과 silane 처리군에서는 sandblasting 군 및 무처리 대조군에 비해 상대적으로 적은 접 착계면에서의 파절(adhesive failure) 양상을 나타내었다. 5. 전단접착강도와 파절양상의 관계에서, 접착강도가 클수록 응집 파괴(cohesive failure) 양상이 많이 나타나는 경향을 보였다.

• 대한치과기공학회지
• /
• 제34권2호
• /
• pp.67-73
• /
• 2012

연구 목적: 임플란트의 하부구조를 상부 구조와 연결하는 레진시멘트의 접착강도를 높이기 위한 기계적 화학적인 표면처리 방법들이 연구 되고 있다. 이 연구에서 다양한 크기의 $Al_2O_3$ sandblasting과 Silano Pen으로 표면처리한 티타늄과 레진 시멘트의 접착강도를 알아보고자 한다. 연구 방법: 12개의 티타늄(Ti-6A1-4V)시편을 디스크 형태로 제작하여 자가중합 수지에 매립하였다. 이들을 각각 6개의 군으로 나누어 $50{\mu}m$, $90{\mu}m$, $110{\mu}m$ 등 3가지 크기의 $Al_2O_3$로 sandblasting 하는 조건과 $Al_2O_3$로 sandblasting한 후 Silano Pen(Bredent, bredent GmbH &Co.KG, Senden, Germany)을 사용한 군으로 나누었다. 표면처리 한 티타늄 표면에 레진시멘트(Duolink dual syringe, Bisco, USA)으로 접착하였다. 그 후 증류수($37^{\circ}C$)에 24시간 보관 후 접착강도 실험을 시행하였고, SEM을 사용하여 표면처리 한 표면과 접착강도 실험 후 파절양상을 관찰하였다. 결과: 통계학적 분석에 따르면 Silano Pen을 사용하여 표면처리한 군들의 접착강도가 높았다(P<0.05). 결론: Silano Pen을 사용하는 것이 티타늄과 레진시멘트의 접착강도를 증가 시킨다.

• 대한치과보철학회지
• /
• 제45권2호
• /
• pp.182-190
• /
• 2007

Statement of problem: Titanium has many advantages of high biocompatibility, physical properties, low-weight, low price and radiolucency, but it is incompatible with conventional dental porcelain due to titanium's oxidative nature. Many previous studies have shown that they used the method of sandblast for surface treatment prior to porcelain application, the researches are processing about the method of acid etching or surface coating. Purpose: The purpose of this research is to study the effect on bond strength of surface roughness between titanium and porcelain with the same surface topography. Material and method: In this study, we evaluated the bond strength by using 3-point bending test based on ISO 9693 after classified 8 groups - group P : polished with #1200 grit SiC paper, group S10 : $1.0{\mu}m$ surface roughness with sandblasting, group S15 : $1.5{\mu}m$ surface roughness with sandblasting, group S20 : $2.0{\mu}m$ surface roughness with sandblasting, group S25 : $2.5{\mu}m$ surface roughness with sandblasting, group S30 : $3.0{\mu}m$ surface roughness with sandblasting, group S35 : $3.5{\mu}m$ surface roughness with sandblasting, group E : $1.0{\mu}m$ surface roughness with HCl etching. Results: Within the confines of our research, the following results can be deduced. 1. In the results of 3-point bending test, the bond strength of sandblasting group showed significant differences from one of polishing group, acid etching group(P<.05). 2. The bond strength of sandblasting groups did not show significant differences. 3. After surface treatments, the group treated with sandblasting showed irregular aspect formed many undercuts, in the SEM photographs. The bond strength of sandblasting group was higher than 25 MPa, the requirement of ISO 9693. Conclusion: In above results, bond strength of titanium and low-fusing porcelain is influenced more to surface aspect than surface roughness. And titanium has clinically acceptable bond strength below surface roughness of $3.5{\mu}m$.

• 대한치과보철학회지
• /
• 제40권6호
• /
• pp.590-596
• /
• 2002

The resin : metal interface is at the basis of most bonding failures in resin-bonded prosthesis. Although debonding has been a problem with adhesive fixed partial dentures, various dentists classify them as long-term restorations. The advantages of resin-bonded fixed partial dentures include minimal tooth reduction and the possibility of rebonding. if resin-bonded protheses can be easily rebounded, it is of clinical importance to know if the lutingagents rebond as well the second time as they did originally. Several retentive systems for resin-to-metal bonding have recommended. Treatments such as electrolytic etching and silicone coating, despite the good result of bond strength, have proved to be time-consuming and technique-sensitive. Therefore a simple and more reliable method is desirable. This study evaluated the effect of metal surface treatments on the rebond strength of panavia 21 cement to a nickel-chromium(Ni-Cr) alloy. The samples were received the following surface treatments : Group No.1 (control or served as the control) treatment with sandblasting with 50um aluminum oxide and ultrasonically cleaned for 10minutes in double-deionized water, Group No.2 were no surface treatments. Group No.3 were treated with metal primer. Group No.4 were treated with sandblasting as previously described, and then metal priming. From the analysis of the results, the following conclusions were drawn. 1. Sandblasting and metal priming appears to be an effective method for treatment of metal after accidental debonding. 2. Group without surface treatment had significantly lower bond strengths compared with other groups. 3. The combination of sandblasting and metal priming may not develop superior bonding strengths compared with other techniques that used the Ni-Cr alloys. 4. Combination of cohesive and adhesive failures were the most common type observed. The results support the use of sandblasting as a viable procedure when rebonding accidentally lost adhesive partial denture. We concluded that sandblasting and metal priming of metal surface before bonding could provide the adequate bond strength during rebonding of resin-bonded fixed partial denture.

• 대한소아치과학회지
• /
• 제35권2호
• /
• pp.195-204
• /
• 2008

치아 우식증과 침식증의 진단과 본 연구는 교정용 밴드 사용의 대안으로 제시된 직접 부착 술식이 보철 치료를 받은 치아상에서도 적절한 결합 강도를 갖으면서 임상적으로 유용하게 사용될 수 있는지를 평가하고, 불산과 포세린 전처리제의 사용 여부에 따른 결합 강도와 접착 파절 양상의 차이에 대해 알아보고자 시행하였다. 사람의 상하악 소구치 치관 20개를 대조군으로, 소구치의 협면을 복제한 포세린 치관 80개를 실험군으로 나눈 후, 대조군은 37% 인산으로 산부식한 후 Transbond $XT^{(R)}$를 이용하여 금속 브라켓을 접착하였고, 실험군들은 모두 포세린 치관에 통상적으로 sandblasting 처리를 하되, 9.6% 불산으로 4분간 부식처리를 함께 한 군, 포세린 전처리제를 적용한 군, 마지막으로 sandblasting과 불산 그리고 포세린 전처리제를 모두 적용한 군으로 20개씩 나눈 후 금속 브라켓을 접착하였다. 각 군간 전단 결합 강도와 접착 파절 양상을 비교하여 관찰한 결과, 포세린 치관에 금속 브라켓을 접착할 시, 기존의 비심미적인 밴드를 사용하지 않더라도 sandblasting과 불산 그리고 포세린 전처리제를 이용한 직접 부착 술식으로 임상적으로 유용하게 사용될 수 있음을 알 수 있었다.

• 대한치과교정학회지
• /
• 제44권3호
• /
• pp.105-112
• /
• 2014

Objective: The purpose of this study was to evaluate the effects of three different surface conditioning methods on the shear bond strength (SBS) of metal brackets bonded directly to gold alloy with chemically cured resin. Methods: Two hundred ten type III gold alloy specimens were randomly divided into six groups according to the combination of three different surface conditioning methods (aluminum oxide sandblasting only, application of a metal primer after aluminum oxide sandblasting, silica coating and silanation) and thermocycling (with thermocycling, without thermocycling). After performing surface conditioning of specimens in accordance with each experimental condition, metal brackets were bonded to all specimens using a chemically cured resin. The SBS was measured at the moment of bracket debonding, and the resin remnants on the specimen surface were evaluated using the adhesive remnant index. Results: Application of metal primer after aluminum oxide sandblasting yielded a higher bond strength than that with aluminum oxide sandblasting alone (p < 0.001), and silica coating and silanation yielded a higher bond strength than that with metal primer after aluminum oxide sandblasting (p < 0.001). There was no significant change in SBS after thermocycling in all groups. Conclusions: With silica coating and silanation, clinically satisfactory bond strength can be attained when metal brackets are directly bonded to gold alloys using a chemically cured resin.

• 대한치과보철학회지
• /
• 제37권5호
• /
• pp.651-657
• /
• 1999

This study was performed to investigate the retrievability of the cementation type implant abutments. The cements used in this study were Cavitec, Tembond and Zinc Phosphate Cement. The types of surface conditioning were no treatment, 50 microne sandblasting, 250 microne sandblasting, fine diamond finishing point and coarse diamond point. The retention of cast crown was measured with Instron Universal Testing Machine(Instron Engineering Co., U.S.A.). The results were as fellows: 1. The Maximium retention was obtained by the group of Z.P.C. cementation and Coarse diamond point surface conditioning. 2. Z.P.C. shows maximum retention, and reduced in orders Tembond, Cavitec, No cement. 3. The value of retention of surface condition was highest in coarse diamond point, lowest in no tretment. 4. The similar results were obtained between fine diamond point and 50 microne sandblasting, coarse diamond point and 250 microne sandblasting. 5. The were no direct corelation between mechanical retention and cementation retention.

• 대한치과보철학회지
• /
• 제30권1호
• /
• pp.85-91
• /
• 1992

The purpose of this study was to evaluate the bonding strength between porcelain laminate and Ni-Cr alloy in the various surface treatments of the bonding faces. For this study the metal surface of specimens were treated : 1) etching only, 2) sandblasting only, and 3) sandblasting and etching. The porcelain laminate were made and bonded to the metal specimens with light curing composite resin cement. Instron testing machine was used to measure their bonding strength : and the result was obtained as follows : 1. The bonding strength of the double treatment of the sandblasting and etching group was higher than that of the single treatment of sandblasting or the etching group. 2. The bonding strength of the sand blasting group was higher than that of the etching group. 3. The debonding were mainly occurred between the Ni-Cr alloy and the composite resin cement.

• 수산해양교육연구
• /
• 제10권1호
• /
• pp.79-86
• /
• 1998

In this study, the adhesive effect, blistering behavior and electrochemical polarization behavior of red lead film by the pretreatment work of sandblasting and potassium chromate($K_2CrO_4$) were investigated to prevent the corrosion of gas storage tank under marine environment. The main results obtained are as follows : 1) The adhesive effect of red lead film by the pretreatment work of sandblasting and potassium chromate is more improved than that of red lead film. 2) The blistering occurrence of red lead film by the pretreatment work of sandblasting and potassium chromate is more delayed than that of red lead film. 3) As the anodic potential is increased, corrosion current density of red lead film by the pre treatment work of sandblasting and potassium chromate is lower drained than that of red lead film.