• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.584-594
• /
• 2010

It is difficult to prepare a specimen for directly testing a tensile strength of soils. Therefore, a tensile strength of soils has been measured indirectly. In this study, a mold and sample preparation tool for directly testing a tensile strength of soils has been developed and a tensile strength of weakly cemented sand was measured by using such device. A compressive strength of the cemented sand was also measured and its value was 30 times greater than its tensile strength.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.2 no.1
• /
• pp.1-9
• /
• 1999

To find pertinent soil type and maintenance method for artificial planting ground, the effects of soil compositions{sandy loam(S), vermiculite(V), sandy loam+vermiculite+sand(SVS), sandy loam+ carbonized rice husk+sand(SCS), sandy loam+humus sawdust+sand(SHS)}, and fertilizers (organic, chemical) on plant(kentuckyblue grass) growth were measured and compared from the field experiment. The results are summarized as follows 1. the highest germination rate is found from "vermiculite(V)" and the lowest from "sandy loam(S)" among tested 5 soil compositions. 2. "sandy loam+vermiculite+sand(SVS)" composition shows the highest plant height growth effect (5cm growth during tested 3 months) comparing to other 4 compositions. 3. "sandy loam+vermiculite+sand(SYS)" composition shows the highest ground covering rate after first two months, but it concede its order to "sandy loam+humus sawdust+sand(SHS)" composition after next one month growing. 4. the effects of fertilizers are follows 1) Among the blocks where no fertilizer was tried, the predominant height growth was obvious in "sandy loam+carbonized rice husk+sand(SCS)" and "sandy loam+humus sawdust+sand(SHS)" composition. 2) Among the blocks where chemical fertilizer was tried, relatively positive results were found from "vermiculite(V)" and "sandy loam+vermiculite+sand(SYS)" blocks on germination and growth rate. But on the ground coverage ratio, the effect of "sandy loam+carbonized rice husk+sand(SCS)" composite precede that of those 2 composites. 3) Among the blocks where organic fertilizer was tried, "sandy loam+humus sawdust+sand(SHS)" and "vermiculite(V)" blocks show relatively high ground coverage rate, growth rate than others. 4) When compositional differences were not considered, the block where organic fertilizer was tried shows most positive effects on all 3 measurements-germination ratio, height growth and ground covering.

• Geomechanics and Engineering
• /
• v.1 no.3
• /
• pp.241-257
• /
• 2009

The one-dimensional compressibility of sand is an important property for the estimation of settlement or deformation of sand deposits. The $K_0$ value of sand is also an important design parameter. Experimental results are presented in this paper to study the compressibility of sand in $K_0$ consolidation tests. The $K_0$ consolidation tests were carried out using a triaxial cell and a plane-strain apparatus. Specimens prepared using both the moist tamping and the water sedimentation methods were tested. The testing data demonstrate that the type of testing apparatus does not affect the $K_0$ measurement if proper boundary conditions are imposed in the tests. The data also show that the compressibility and the $K_0$ value of loose sand specimens prepared using the moist tamping method are very sensitive to the variation of void ratio. The $K_0$ values measured from these tests do not agree with the $K_0$ values calculated from Jaky's equation. The compressibility and $K_0$ values of sand obtained from tests on specimens prepared using different preparation methods are different which may reflect the influence of soil fabrics or structures on the one dimensional compression behavior of sand.

• Geomechanics and Engineering
• /
• v.15 no.1
• /
• pp.659-668
• /
• 2018

A series of direct shear tests were implemented on three different types of specimens (i.e., clean Perth sand, sand containing 10, 20 and 30% bentonite, sand containing 1, 3 and 5% slag, and sand containing 10, 20 and 30% bentonite with increasing percentages of added slag (1%, 3% and 5%). This paper focuses on the shear stress characteristics of clean sand and sand mixtures. The samples were tested under different three normal stresses (100, 150 and 200 kPa) and three curing periods of no curing time, 7 and 14 days. It was observed that the shear stresses of clean sand and mixtures were increased with increasing normal stresses. In addition, the use of slag has improved the shear strength of the sand-slag mixtures; the shear stresses rose from 128.642 kPa in the clean sand at normal stress of 200 kPa to 146.89 kPa, 154 kPa and 161.14 kPa when sand was mixed with 1%, 3% and 5% slag respectively and tested at the same normal stress. Internal friction angle increased from $32.74^{\circ}$ in the clean sand to $34.87^{\circ}$, $37.12^{\circ}$ and $39.4^{\circ}$ when sand was mixed with 1%, 3% and 5% slag respectively and tested at 100, 150, and 200 kPa normal stresses. The cohesion of sand-bentonite mixtures increased from 3.34 kPa in 10% bentonite to 22.9 kPa, 70.6 kPa when sand was mixed with 20% and 30% bentonite respectively. All the mixtures of clean sand, different bentonite and slag contents showed different behaviour; some mixtures exhibited shear stress more than clean sand whereas others showed less than clean sand. The internal friction angle increased, and cohesion decreased with increasing curing time.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.338-345
• /
• 2000

In this study, applicability of PMT in domestic area and test procedure were studied. At six test holes of three construction sites in Pusan, PMT using Elastometer-200 type was done. The problems during test were investigated and the test results were analysed. Limit pressure, p$\sub$ι/ could be determined by p- Δv/v method. Using PMT results, marine soil in Pusan could be classified approximately. Net limit pressure value was in the range of 6.4 ∼ 22.5 kg/$\textrm{cm}^2$ in clay, 2.2 ∼ 30.0 kg/$\textrm{cm}^2$ in sand, 13.0 ∼ 58.0 kg/$\textrm{cm}^2$ in weathered soil and 47.0 ∼ 190.0 kg/$\textrm{cm}^2$ in weathered rock. Also, E$\sub$m//p$\sub$ι/ value was in the range of 2.4 ∼ 7.0 in clay, 2.6 ∼ 12.1 in sand, 6.8 ∼ 17.1 in weathered soil and 7.2 ∼ 29.6 in weathered rock.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.6
• /
• pp.44-48
• /
• 2002

In lateral ground flow, slope stability, and land slide problems, H-piles have often been used, on a horizontally deforming ground, to prevent the failure of mass of soil in a downward and outward movement of a slope. Here, theoretical equations are derived to estimate the lateral force, assuming that the Mohr-Coulomb's plastic states occur in the ground, just around H-piles. In this study, some model experiments were performed to check the lateral forces determined from theoretical equations, using several pile widths, heights and various interval ratios between H-piles for sand specimens. The solution of the theoretical equation, derived from previous studies, showed reasonable characteristics for constants of soil, as well as for the interval, widths, and heights of H-Pile.

• Journal of Industrial Technology
• /
• v.30 no.B
• /
• pp.25-32
• /
• 2010

In this paper stability about lateral soil movement of bridge abutment constructed on the soft ground, reinforced with the sand compaction pile (SCP) and the preconsolidaton methods, was evaluated by using the centrifuge testing facility which stress conditions in field could be reconstructed in the laboratory. The layouts of model such as ground condition, sand compaction piles and abutment was determined on the basis of similitude law with the reduced scale of 1/200. Construction sequences of installing SCP, preparing reclaimed ground, preconsolidating ground and building the piled bridge abutment were reconstructed during centrifuge modelling and measurements of movement were followed in each sequence. From analyzing the results of measuring movements of the model abutment and the ground, measured lateral movement of model abutment was found to be within the allowable value so that stability of abutment against lateral sliding was secured.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.569-576
• /
• 2002

Recently, the hydraulic fill method is commonly used in many reclamation projects due to lack of fill materials. The method of hydraulic fill in reclamation is executed by transporting the mixture of water-soil particles into a reclaimed land through dredging pipes, then the dredged soil particles settle down in the water or flow over an out flow weir with the water. In the present study, to compare the soil and sand-mat mixed method with sand-air jet method for shallow improvement of hydraulic fills at southern seashore, the model tests were performed. Through the model test results, the behavior of surface as disturbance of desiccation crust is analyzed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.672-679
• /
• 2008

During recent years, the large soft ground improvements very rapidly increase with industrial development and it is the types and scales of structure that is enlarged by degree. Then, we must enter construct equipment to improve soft ground and we fulfilled works by carrying out soft clay soil to gain trafficability for them. For improving the soft ground, we lay geotextile on soft clay ground and fill the filter sand that can drain the pore water. Then, we landfill cover soil for come by trafficability of construction tools. Ater that we penetrate vertical drain for dehydration through soft ground. there are very complicated works. For these reason we suggest the methods of soft ground improvement constructions.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.3-26
• /
• 2009

Superloading yield surface concept is newly introduced together with subloading yield surface conception in order to describe full gradation continuously of the mechanical behavior of soils from typical sand through intermediate soil to typical clay (All Soils). Finite deformation theory has been applied to the soil skeleton-pore water coupled continuum mechanics, which enables us to discuss things in a perpetual stream from stable state to unstable state like from deformation to failure and vice versa like from liquefaction to post liquefaction consolidation of sand (All States). Incremental form of the equation of motion has been employed in the continuum mechanics in order to incorporate a rate type constitutive equation, which is "All Round" enough to predict ground behavior under both static and dynamic conditions. The present paper is the shortened version of the lecture note delivered in 2008 Theoretical and Applied Mechanics Conference, Science Council Japan, but with newly developed application examples.