• 펄프종이기술
• /
• 제38권5호
• /
• pp.24-30
• /
• 2006

This study was performed to characterize inverse emulsion type cationic polyacrylamide (PAM) and to compare with powder and salt dispersion type PAMs as a retention and drainage aid. Salt dispersion type PAM has defects of high amount of salt which increases conductivity of white water, low active polymer contents and relatively worse retention and drainage properties than others because of its low molecular weight. Powder type PAM has benefit of high active polymer contents and good retention and drainage properties, but defects of low dissolution speed and insoluble particle generation were observed. However, inverse emulsion type showed the best retention and drainage aids among them by controlling molecular weight and morphology easily and it had relatively higher active polymer contents and better solubility.

• 방사성폐기물학회지
• /
• 제18권3호
• /
• pp.337-346
• /
• 2020

Two commonly used ceramics in molten salt research are alumina and mullite. The two ceramics were exposed to a combination of rare earth chlorides (YCl₃, SmCl₃, NdCl₃, PrCl₃, and CeCl₃; each rare earth chloride of 1.8 weight percent) in LiCl-KCl at 773 K for approximately 13 days. Scanning electron microscopy with wave dispersion spectra was utilized to investigate a formation layer or deposition of rare earths onto the ceramic. Only the major constituents of the ceramics (Al, Si, and O₂) were observed during the wave dispersion spectra. X-ray fluorescence was used as well to determine concentration changes in the molten salt as a function of ceramic exposure time. This study shows no evidence of ionic exchange or layer formation between the ceramics and molten chloride salt mixture. There are signs of surface tension effects of molten salt moving out of the tantalum crucible into secondary containment.

• 한국광물학회지
• /
• 제20권1호
• /
• pp.21-33
• /
• 2007

벤토나이트의 분산/응집 거동은 시추이수의 성능에 큰 영향을 줌으로 주요 관심의 대상이 된다. 본 연구에서는 상업적으로 활용되고 있는 3종의 벤토나이트[2종의 CMC (carboxy-methyl cellulose)처리 벤토나이트와 1종의 무처리 벤토나이트]에 대하여 pH와 염분농도가 다른 용액에서의 분산/응집 특성을 분석하였다. 또한, 벤토나이트 현탁액의 점성 변화를 시추용 이수의 유동학적 측면에서 검토하였다. 벤토나이트의 분산/응집 거동은 비색분석법과 광분산법의 두 방법으로 측정되었으며, 광분산법으로 침전된 입자의 직경과 침전속도도 검토하였다. 벤토나이트의 종류와 수질에 따라 분산/응집 거동은 다양하게 나타났다. 초기 10분 동안에 모든 종류의 벤토나이트는 좋은 분산 특징을 보여주나, 이후에 CMC를 함유한 벤토나이트들은 다소 응집되는 특성을 보여주었다. 염수에서는 모든 시료들이 응집되는 특성을 보이여 응집속도는 염의 농도와 폴리머의 농도에 따라 변화하였다. 침전된 응집물의 부피는 염의 농도가 증가됨에 따라 감소하였다. 용액의 pH는 시료의 분산/응집 거동에 주요한 영향을 미치며, 응집 속도와 응집입자의 직경은 용액의 pH가 감소함에 따라 증가하였다. 반면에, 침전된 응집물의 부피는 pH가 증가됨에 따라 증가하였다. 응집 속도가 빠른 벤토나이트 분산용액은 점성이 낮았다. 다양한 환경에서 벤토나이트를 시추이수용으로 적용하고자 할 경우, 본 연구의 결과들은 유용한 자료로 활용될 수 있을 것이다.

• Elastomers and Composites
• /
• 제48권2호
• /
• pp.114-124
• /
• 2013

글리세라이드의 지방산 사슬길이 및 구조적 차이에 따른 영향을 평가하기 위하여 팜오일에서 추출된 글리세롤과 palmitic acid, stearic acid등 사슬길이가 $C_{12}{\sim}C_{18}$인 지방산을 이용하여, mono, di, tri등 다양한 글리세라이드 구조를 가진 신규 분산제를 합성하였고, 이를 실리카 충진배합물에 적용하여 기존의 금속염 분산제와 비교평가 하였다. 실험결과, 글리세라이드 분산제는 기존의 금속염 지방산 분산제 대비 혼합고무 내 윤활효과가 낮아서 혼합고무의 점도는 높으나, 실리카 분산이 크게 향상됨을 확인하였다. 이는 기계적 물성과 마모성능, Payne effect로 확인되었다. 또한 글리세라이드의 지방산 사슬길이가 길수록, 글리세롤에 중합된 지방산 수가 적을수록(tri- < di-< mono-glyceride)혼합고무 내 실리카 분산특성은 향상되었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.722-727
• /
• 2004

This paper includes the comparative study between Cr plating and nitriding process with an aim at improving corrosion, wear and maintainability for KNR(Korean Next Generation Rifle) 5.56mm barrel. The endurance test was conducted to compare the performance of standard barrel, Cr plating barrel and nitriding barrel. Main activities are described as follows; optimal Cr plating and nitriding process set-up for KNR 5.56mm barrel; durability test of each barrel(20,000 rounds); salt water immersion test; dispersion, initial velocity, inner diameter data acquisition. According to the results of this firing test, Cr plating barrel is superior to standard barrel and nitriding barrel in view of corrosion, wear and maintainability

• 한국군사과학기술학회지
• /
• 제7권1호
• /
• pp.5-12
• /
• 2004

This paper includes the comparative study between Cr plating and nitriding process with an aim at improving corrosion, wear and maintainability for KNR(Korean Next Generation Rifle) 5.5mm barrel. The endurance test was conducted to compare the performance of standard barrel, Cr plating barrel and nitriding barrel. Main activities are described as follows; optimal Cr plating and nitriding process set-up for KNR 5.56mm barrel; durability test of each barrel(20,000 rounds); salt water immersion test; dispersion, initial velocity, inner diameter data acquisition. According to the results of this firing test, Cr plating barrel is superior to standard barrel and nitriding barrel in view of corrosion, wear and maintainability.

• 한국응용과학기술학회지
• /
• 제10권1호
• /
• pp.49-55
• /
• 1993

Ground Calcium Carbonate, among paper coating pigments, will influence less dispersant demand, less binder demand, increase coating solids from 58% to 70%, which means high speed coating, less shrinkage during drying, less energy consumption, more uniform coverage of fibers. The quality point of view of Ground Calcium Carbonate, brightness, particle size, Particle size distribution, hardness, impurities content are important. More important factors of Ground Calcium Carbonate which influence the paper coating process are dispersion mechanisms and their effects. The study was made to investigate the effect of Ground Calcium Carbonate dispersion by sodium salt of polyacrylate dispersant composition and dispersion condition. Basic tests such as physical, optical and chemical were perfumed, and dispersion effects were investigated by different conditions. The results showed that the type of dispersant affected the dispersion effects, and the Ground Calcium Carbonate has critical dispersant demand.

• 폴리머
• /
• 제30권3호
• /
• pp.224-229
• /
• 2006

3-Aminopropyldimethylethoxysilane (AS)과 methyliodide를 이용하여 4차 암모늄 실란을 제조하고 7,7,8,8-tetracyanoquinodimethane (TCNQ)과 methyliodide 및 요오드화 리튬을 이용하여 $Li^+TCNQ^-$를 제조하였다. 제조한 4차 암모늄 실란에 $Li^+TCNQ^-$를 가하여 4차 암모늄 실란-TCNQ adduct(ST)를 제조하고 이를 말단에 OH기를 갖는 poly(dimethylsiloxane) (PDMS)과 축합반응시켜 poly(dimethylsiloxane)-ST adduct(PST)를 제조하였다. PST 변성 말레화 폴리에틸렌(PST-g-MPE)은 말레화 폴리에틸렌과 PST를 internal mixer(Rheomix 600P)를 사용하여 용융중합으로 제조하였으며 여기에 카본블랙 (CB)의 함량을 변화시켜 PST-g-MPE/CB 및 MPE/CB 복합체를 제조하였다. 제조한 복합체의 열적 특성을 측정한 결과 유사한 열분해 온도를 나타내었다. PST-g-MPE/CB 복합체의 인장강도는 카본블랙의 함량 증가에 따라 $200\sim308MPa$로 증가하였으며 모폴로지를 측정한 결과 MPE/CB 복합체보다 PST-g-MPE/CB 복합체의 경우에서 카본블랙의 분산이 보다 더 잘 이루어졌음을 확인하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.323-329
• /
• 2004

The electrical and rheological properties pertaining to the electrorheological (ER) behavior of chitosan derivatives, chitosan, chitosan ammonium salt and chitosan phosphate suspensions in silicone oil were investigated. Chitosan derivative suspensions showed a typical ER response (Bingham flow behavior) upon application of an electric field. However, chitosan phosphate suspension exhibited an excellent shear yield stress compared with chitosan and chitosan ammonium salt suspensions. The difference in behavior results from the difference in the conductivity of the disperse phases due to the difference of their polarizability. The shear stress for the chitosan, chitosan ammonium salt and chitosan phosphate suspensions exhibited a linear dependence on the volume fraction of particles and 1.18 ,1.41 and 1.67 powers of the electric field. On the basis of the experimental results, the newly synthesized chitosan derivative suspensions found to be an ER fluid.

• KSTLE International Journal
• /
• 제5권2호
• /
• pp.49-51
• /
• 2004

The electrical and rheological properties pertaining to the electrorheological (ER) behavior of chitosan derivatives, chitosan, chitosan ammonium salt and chitosan phosphated suspensions in silicone oil were investigated. Chitosan derivative suspensions showed a typical ER response (Bingham flow behavior) upon application of an electric field. However, chitosan phosphate suspension exhibited an excellent shear yield stress compared with chitosan and chitosan ammonium salt suspensions. The difference in behavior results from the difference in the conductivity of the disperse phases due to the difference of their polarizability. The shear stress for the chitosan, chitosan ammonium salt and chitosan phosphate suspensions exhibited a linear dependence on the volume fraction of particles and 1.18, 1.41 and 1.67 powers of the electric field. On athe basis of the experimental results, the newly synthesized chitosan dervative suspensions found to be an ER fluid.