• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.1302-1308
• /
• 2010

This study the change of the safety factor before and after the reinforcement were compared by performing the parameter research based on the limit equilibrium analysis regarding the same cross section after carrying out the safety factor before the reinforcement on the virtual section in order to observe the change of the safety factor of the slop reinforced with the slope planting reinforced earth, and the variation of the safety factor according to the increase of the length of the reinforcement materials and the change of the slope height was analyzed. As the result, the reinforcement effect was insignificant at no more than 0.6 of L/H, the reinforcement length ratio when the reinforcement length was increased, as the increase of the safety factor was slow comparing with the non-reinforced slope. At 3.0m of the slope height, reinforcement on the slope is not necessary, and at 3.0m to 5.0m of the slope height, the inclination was not influencing at no less than 0.6 of L/H. At 5.0m to 9.0m of the slope height, the safety factor was mostly secured on the slope at 0.8 of L/H and the over-reinforced slope appeared at no less than 1.0 of L/H. Also, the safety factor increased as the slope height increases and the slope gets steeper till 0.8 of L/H, but the slope steepness affects more on the increase of the safety factor than the reinforcement material, as the reinforcing force by the reinforcement material became steady.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.129-136
• /
• 2005

The deterministic analysis method has generally used to evaluate the slope stability and it evaluates the slope stability with decision value that is a representative value of design variables. However, one of disadvantages in the deterministic approach is there is not able to consider the uncertainty of soil strength properties, even though it is the biggest influential parameter of the slope stability. On the other hand, the limit state design(LSD) can take a consideration of uncertainties and computes both the reliability index and the probability of failure. LSD method is capable of overcoming the disadvantages of deterministic method and evaluating the slope stability more reliably. In this study, both the mean value and standard deviation of the internal land's representative soil strength properties applied to process the LSD method. The major purpose of this study is to gauge the general applicability of the limit state design in soil slope and to weigh the comparative validity of the proposed partial safety factor. In order to reach the aim of this study, the partial safety factor and resistance factor which totally satisfied the slope's overall safety factor were calculated by the load and resistance safety factor design (LRFD).

• 한국농공학회지
• /
• 제31권1호
• /
• pp.58-70
• /
• 1989

The paper compared the Bishop methed to the Fellenius method in the analysis of slope stability. Laboratory model test was carried out in the case of seepage flow considered. The results obtained from this study were summarized as follows; 1. The slice pieces of 10 were enough to analysis the slope stability. 2. The safety factor. by the Fellenius method was lower than the Bishop method by the 96 to 97% in the case of no seepage flow and by the 95 to 96% in the case of seepage flow considered. 3. Besides the parameter of soil and slope, the safety factor of slope was influenced by the height of slope. This phenomena was distinct in the height of height less than 10 meters. 4. In the case of clay, there was no difference in the safety factor of slope between Fellenius and Bishop rnethod. The safety factors of slope with the seepage flow considered were lower than those with no see-page flow. 5. The influence of cohesion on the safety factor was more significant in the Bishop method than in the Fellenius method. 6. The slope failure of model test of A and B soil samples with high permeability coefficient was taken place slightly in vicinity of toe by the concentration of stress and gradually increased 7. Under condition of same slope height, the shapper the slope, the shorter the radius and the center of critical circle appered downward and finally failure of slope occured inside the slope.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 사면안정학술발표회
• /
• pp.83-91
• /
• 2003

Always slope according to construct road exist danger because of environment unstability factor in slope, Since this research an inclination of slope is gentle slope (1：1.5∼1：9.0) but falling happened by conduct of continuous ground movement. And this study considered more economical and efficient reinforcement method for slope stability. The various reinforcement methods are applied to execute examination of slope stability. Applied reinforcement methods satisfied safety factor And this research region is performing continuous measurement about ground movements and displacements.

• 지질공학
• /
• 제24권3호
• /
• pp.333-341
• /
• 2014

The construction of roads, tunnels, and bridges results in changes to the local terrain that may influence the ground safety factor, which represents the stability of geotechnical structures. In this study, we assessed construction sites that had collapsed as a result of terrain change, and then simulated variation in the ground safety factor with respect to terrain change caused by road construction. We assumed steep slopes to simulate changes in terrain in a mountainous area and assumed that earthworks took place for road construction by cutting a platform into the slope and altering the slope angle of the terrain both above and below the road. We calculated values of the ground safety factor through a stability analysis of the slope both above and below the road, and examined the variation in the safety factor of the above- and below-road slopes with respect to changes in road width. We found that if the slope angle was the same above and below the road, then the change in the ground safety factor during/after road construction occurred in the slope below the road, and if the slope angle above the road differed from that below, then the change occurred in both the above- and below-road slopes. Furthermore, the ground safety factor was essentially constant for road widths exceeding 2-6 m, depending on both above- and below-road slope angle. The findings of this study can be used to guide the management of construction sites and to assess changes in ground stability during road construction work, particularly in the early stages of earthworks, when the road width is narrow.

• 한국산학기술학회논문지
• /
• 제17권12호
• /
• pp.496-503
• /
• 2016

억지말뚝으로 보강된 무한사면의 해석을 위해 억지말뚝에 작용하는 하중을 소성변형이론과 소성흐름이론을 적용하여 산정하였고 무한사면의 안전율에 영향을 미치는 다양한 인자들의 효과를 살펴보았다. 해석결과에 따르면 억지말뚝의 설치로 인해 사면의 안전율이 상당히 증가함을 알 수 있었고 말뚝설치간격이 커질수록 안전율은 감소하였다. 억지말뚝의 설치로 인한 안전율의 증가가 커서 무한사면의 침투발생 유무가 사면의 안전율에 미치는 영향은 상대적으로 미미할 것으로 생각된다. 억지말뚝으로 보강된 무한사면의 안전율을 수식으로 나타내 보았는데 무보강시 무한사면의 안전율에 영향을 미치는 흙의 강도정수 및 사면의 경사 그리고 사면의 두께 이외에도 무한사면요소의 폭과 길이 그리고 억지말뚝에 작용하는 하중에 영향을 받음을 알 수 있었다. 소성변형이론을 바탕으로 하여 억지말뚝보강 무한사면의 안전율을 흙의 강도갱수를 달려하여 살펴본 결과 무보강시에 비해 상당한 안전율 증가효과를 확인할 수 있었는데 본 연구에서 고려한 강도정수와 말뚝간격에 대하여 최소 안전율은 13.7이었고 최대 안전율은 65.6이었다. 억지말뚝의 지름이 증가할수록 말뚝이 부담하는 하중은 증가하지만 안전율은 감소하였는데 이는 억지말뚝 보강 무한사면의 안전율에 영향을 미치는 무한사면요소의 폭과 길이 때문으로 판단된다. 소성흐름이론을 바탕으로 억지말뚝 보강 무한 사면의 안전율을 평균유입속도와 소성점도의 곱($v_1{\eta}_p$)을 달려하여 살펴본 결과 무보강시에 비해 상당한 안전율 증가효과를 확인할 수 있었으며 $v_1{\eta}_p$값이 커질수록 안전율도 커짐을 알 수 있었고 일정한 $v_1{\eta}_p$값에 대하여 말뚝설치간격이 커질수록 안전율은 감소하였다.

• 한국농공학회논문집
• /
• 제55권6호
• /
• pp.37-46
• /
• 2013

Many factors about the stability for the reservoir embankments is determined when the facility is completed. Therefore the initial design of the embankment is important. Many researchers focused the effect of soil parameters although the cross section greatly affects the stability and can be controlled in design step. The objective of this research is to analysis of the effects for the safety factor of slope and seepage according to change cross-section in embankment. As a result, the quantity of seepage decreased as the gradient of downstream slope decreased and was proportional to the height of embankments. There was a linear relationship between the gradient of slope and the safety factor of slope. However the gradient of slope did not affect other side slope. All in a relationship, regressive equations with a high correlation coefficient were calculated and can be applied the simple estimation method of the stability using the cross-section. As results of analyzing the sensitivity, the friction angle and permeability critically effect for the slope stability and the seepage, respectively. The effect of the slope gradient was similar to major soil properties.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1998년도 토목섬유 학술발표회 논문집
• /
• pp.115-122
• /
• 1998

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.697-702
• /
• 2006

A counterplan of slope failure has to investigate about various and engineering safety factors. Especially, it is important that large cut-slope must examine rational and economic solution. In this case study, cut-slope failure caused by inflow of rainwater into alternate layers. Hereafter it is suggested that large cut-slope should consider analysis the cause for a decline of safety factor and the engineering character of corestone ground mass.

• 지질공학
• /
• 제22권4호
• /
• pp.375-385
• /
• 2012

본 연구에서는 강우지속시간과 강우종료 후 침투에 의한 깎기비탈면 안전율 변화를 고찰하였다. 강우강도와 강우지속시간의 다양한 조건에서 깎기비탈면의 침투특성과 안전율 변화는 soilworks 프로그램으로 분석하였다. 분석 결과, 깎기비탈면 안전율은 강우 종료 후에 간극수압의 증가로 추가적으로 감소하여 최소 안전율에 도달한다. 강우지속시간 동안 안전율 감소율보다 강우종료 후 안전율 감소율이 더 큰 경우도 발생하게 되므로, 깎기비탈면 침투해석 시 유의해야 할 것이다.