• Journal of the Korean GEO-environmental Society
• /
• v.7 no.6
• /
• pp.101-111
• /
• 2006

In case of drilled shafts installed by drilling through soft overburden onto a strong rock, the piles can be regarded as end-bearing elements and their working load is determined by the safe working stress on the pile shaft at the point of minimum cross-section or by code of practice requirements. Drilled shafts drilled down for some depth into weak or weathered rocks and terminated within these rocks act partly as friction and partly as end-bearing piles. The base resistance component can contribute significantly to the ultimate capacity of the pile. However, the shaft resistance is typically mobilized at considerably smaller pile movements than that of the base. In addition, the base response can be adversely affected by any debris that is left in the bottom of the socket. The reliability of base response therefore depends on the use of a construction and inspection technique which leaves the socket free of debris. This may be difficult and costly to achieve, particularly in deep sockets, which are often drilled under water or drilling slurry. As a consequence of these factors, shaft resistance generally dominates pile performance at working loads. The efforts to improve the prediction of drilled shaft pile performance are therefore primarily concerned with the complex mechanisms of shaft resistance development. In this study, the numerical analyses are carried out to investigate the behavior characteristics of side of rock socketed drilled shafts varying the loading condition at the pile head. The difference of behavior characteristics of side resistance is also evaluated with the effects of modelling of asperity.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.38 no.1
• /
• pp.43-48
• /
• 2020

Open pit mines for limestone mining require rapid development of technologies and efforts to prevent safety accidents due to rapid deterioration of the slope due to deforestation and rapid changes in the topography. Accurate three-dimensional spatial information on the terrain should be the basis for reducing environmental degradation and safe development of open pit mines. Therefore, this study constructed spatial information about open pit mine using UAV(Unmanned Aerial Vehicle) and analyzed its utility. images and 3D laser scan data were acquired using UAV, and digital surface model, digital elevation model and ortho image were generated through data processing. DSM(Digital Surface Model) and ortho image were constructed using image obtained from UAV. Trees were removed using 3D laser scan data and numerical elevation models were produced. As a result of the accuracy analysis compared with the check points, the accuracy of the digital surface model and the digital elevation model was about 11cm and 8cm, respectively. The use of three-dimensional geospatial information in the mineral resource development field will greatly contribute to effective mine management and prevention of safety accidents.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.65-65
• /
• 2012

Copper zinc tin sulfide ($Cu_2ZnSnS_4$, CZTS) is a very promising material as a low cost absorber alternative to other chalcopyrite-type semiconductors based on Ga or In because of the abundant and economical elements. In addition, CZTS has a band-gap energy of 1.4~1.5eV and large absorption coefficient over ${\sim}10^4cm^{-1}$, which is similar to those of $Cu(In,Ga)Se_2$(CIGS) regarded as one of the most successful absorber materials for high efficient solar cell. Most previous works on the fabrication of CZTS thin films were based on the vacuum deposition such as thermal evaporation and RF magnetron sputtering. Although the vacuum deposition has been widely adopted, it is quite expensive and complicated. In this regard, the solution processes such as sol-gel method, nanocrystal dispersion and hybrid slurry method have been developed for easy and cost-effective fabrication of CZTS film. Among these methods, the hybrid slurry method is favorable to make high crystalline and dense absorber layer. However, this method has the demerit using the toxic and explosive hydrazine solvent, which has severe limitation for common use. With these considerations, it is highly desirable to develop a robust, easily scalable and relatively safe solution-based process for the fabrication of a high quality CZTS absorber layer. Here, we demonstrate the fabrication of a high quality CZTS absorber layer with a thickness of 1.5~2.0 ${\mu}m$ and micrometer-scaled grains using two different non-vacuum approaches. The first solution-processing approach includes air-stable non-toxic solvent-based inks in which the commercially available precursor nanoparticles are dispersed in ethanol. Our readily achievable air-stable precursor ink, without the involvement of complex particle synthesis, high toxic solvents, or organic additives, facilitates a convenient method to fabricate a high quality CZTS absorber layer with uniform surface composition and across the film depth when annealed at $530^{\circ}C$. The conversion efficiency and fill factor for the non-toxic ink based solar cells are 5.14% and 52.8%, respectively. The other method is based on the nanocrystal dispersions that are a key ingredient in the deposition of thermally annealed absorber layers. We report a facile synthetic method to produce phase-pure CZTS nanocrystals capped with less toxic and more easily removable ligands. The resulting CZTS nanoparticle dispersion enables us to fabricate uniform, crack-free absorber layer onto Mo-coated soda-lime glass at $500^{\circ}C$, which exhibits a robust and reproducible photovoltaic response. Our simple and less-toxic approach for the fabrication of CZTS layer, reported here, will be the first step in realizing the low-cost solution-processed CZTS solar cell with high efficiency.

• Korean Journal of Weed Science
• /
• v.6 no.2
• /
• pp.154-161
• /
• 1986

Since herbicide damage has been occurred in subirrigated rice seedbed in Korea, the use of crop safener is required to reduce crop injury. Field studies were conducted to evaluate safening effect of 1,8-naphthalic anhydride (NA) and CGA 123'407 (4, 6-dichloro-2-phenyl-pyrimidine) against four kinds of paddy herbicides applied to subirrigated vinyl-covered rice seedbed. NA as a seed dressing at 0.5% (W/W) was effective in reducing rice injury from butachlor, pretilachlor, chlormethoxynil and benthiocarb, and increased number of seedling established, plant height, and dry weight of rice seedlings, while growth inhibition and stand loss were observed at 1% NA. Pretilachlor slightly decreased number of seedlings established and inhibited growth of rice seedlings. But pre-mix combination of pretilachlor (2%) and CGA 123'407 (0.5%) reduced rice injury caused by pretilachlor alone and increased number of seedlings established and dry weight of rice seedlings. The results indicate that NA and CGA 123'407 would permit the safe application of butachlor, pretilachlor, chlormethoxynil, and benthiocarb in subirrigated rice seedbed.

• Journal of Conservation Science
• /
• v.31 no.2
• /
• pp.95-104
• /
• 2015

Excavated archaeological cast iron objects in improper storage are quickly corroded and disintegrated into block and powder finally. Hence desalination treatment which is a way of removing internal corrosive factors, especially chloride ion, is an important process. But desalination is often omitted or objects are dehydrated by alcohol because the destruction of objects could occur during desalting. Although current desalting methods mostly use an aqueous alkali solution, $OH^-$ ions of water could accelerate corrosion and broaden internal cracks cause of high surface tension. Therefore this study experimented desalting using ethyl alcohol, which is low surface tension, to investigate an effect of desalination. As a result, desalting using ethyl alcohol showed the similar or more effective results of desalting using water. In addition, as aspects of desalting safety, ethyl alcohol desalting method was smaller destruction of objects and extraction of Fe from the objects than the aqueous alkali solution. However, this study explored the possibility of desalting methods using organic solvent in fieldwork, so the results would provide basic date for making the safe and effective desalting method for archaeological cast iron objects through further experiments.

• Journal of Applied Biological Chemistry
• /
• v.63 no.3
• /
• pp.267-274
• /
• 2020

The dissipation characteristics and kinetics of fungicide mandipropamid and insecticide thiamethoxam in lettuce under greenhouse conditions were investigated at three different lettuce-growing fields for estimating the pre-harvest residue limits (PHRLs). The analytical methods were fully validated for the quantitation of pesticide residues using High-Performance Liquid Chromatography-Photo Diode Array detector or Ultraviolet-Visible Detector and applied to real samples. The lettuces suitable for shipment were harvested during 10 days including pre-harvest interval after treatment at the recommended dose by safe-use guidelines. The initial mean residues in different fields were 6.68-17.87 and 4.96-8.31 mg/kg for mandipropamid and thiamethoxam, respectively, which decreased to 16-54 and 14-44% in 10 days. The clothianidin, a metabolite of thiamethoxam, was detected in <0.02 to 0.37 mg/kg. The dissipation of both pesticides followed first-order kinetics over a period of 10 days after application. Based on the residue data, the mean dissipation rate constant (λ) and biological half-lives (T_1/2) were estimated to be -0.1060 and 6.5 days of mandipropamid and -0.1236 and 5.6 days of thiamethoxam. The PHRLs for lettuce on the 10th and 5th day before harvesting were calculated to be 63.24 and 43.56 mg/kg for mandipropamid, and 44.66 and 25.88 mg/kg for thiamethoxam, with -0.0746 and -0.1091 of the upper 95% confidence intervals of dissipation rate constant, respectively. This work would be useful as guidance for adjusting the shipment date and contribute to stabilizing the income of farmers in Korea.

• The Korean Journal of Pesticide Science
• /
• v.15 no.4
• /
• pp.434-440
• /
• 2011

In order to establish the guidance of management and safe use hazard substance, trend analysis of hazard substance in/on agricultural products reported by press for 5 years (2005-2009) was performed. Data for the analysis collected from the articles about hazard substances from web portals, newspapers and so on. The mostly detected harmful factors in/on agricultural products were pesticides residue and heavy metals by the reports by press for last 5 years. The number of detected pesticides was slightly increased from 14 to 34 through the passage of time but the number of cases reported by press was not increased. On the other hand, the number of accidents and reports related to heavy metals were highly increased from 3 to 13 and 42 to 112, respectively. 65 pesticides including chlorpyrifos were detected in domestic agricultural products for the 5 years. Frequently detected pesticides were chlorpyrifos, endosulfan, carbendazim, azoxystrobin, and procymidone. Pesticide residues were repeatedly detected on green vegetables such as a green perilla leaf, a lettuce, a leek, and spinach among crops.

• The Korean Journal of Pesticide Science
• /
• v.12 no.2
• /
• pp.134-140
• /
• 2008

The data on pesticide poisoning death toll during 2000-2005 was obtained from Korean National Statistical Office and analysed to find out any precautionary measures against pesticide poisonings. Pesticide poisoning death toll showed slightly increasing trend with year up to about 3500 in 2005. Most of the pesticide poisoning death cases were intentional self-poisoning accounting for more than 80% of total pesticide poisoning death. The pesticide most often implicated in poisoning death were paraquat dichloride, a non-selective herbicide and organophosphate/carbamate insecticides. The regional distribution of pesticide poisoning death showed urban 21.6% and rural area 78.4%. As for the occupation of the dead, agricultural, forestry and fishery workers accounted for 27.4% and non-agricultural workers was 72.6% of pesticide poisoning death. Therefore, government need to take some precautionary measures to reduce the number of pesticide poisoning cases. It is strongly recommended that pesticide regulatory authorities encourage and train the agricultural workers to use safe storage boxes and enforce strict regulation for the prevention for the prevention of highly toxic pesticides sales to non-agricultural workers.

• Fisheries and Aquatic Sciences
• /
• v.13 no.1
• /
• pp.63-70
• /
• 2010

Two feeding experiments were conducted to investigate the effects of dietary genetically modified (GM) soya and com on growth performance, feed utilization and body composition of juvenile olive flounder, Paralichthys olivaceus and rockfish, Sebastes schlegelii. For each fish species, four isonitrogenous (50% crude protein) and isocaloric (4.1 kcal/g) diets (designated as nGM soya, GM soya, nGM com and GM com) were formulated to contain 20% non-GM (nGM) and GM soya and com. Thirty olive flounder (initial body weight, 15.4${\pm}$0.4 g) and fifty rockfish (initial body weight, 3.1${\pm}$0.02 g) were distributed in each 400 L tank (200 L water) in a flow through system. Each experimental diet was fed to triplicate groups of fish to visual satiation, twice a day (9:00 hand 17:00 h) for 6 weeks. Growth performance was measured every three weeks. No effects of GM feedstuffs on survival were observed. Dietary inclusion of GM feedstuffs did not affect growth performance and feed utilization of fishes, except for rockfish fed GM com. Rockfish fed the GM com diet showed higher weight gain, daily feed intake and daily protein intake than did fish fed the nGM com diet, but no significant differences were observed in final body weight between the dietary treatments. Condition factor, hepatosomatic index, visceral somatic index and body composition were not altered by the inclusion of GM feedstuffs. These results indicate that dietary inclusion of GM soya and com could have no effects on growth performance and feed utilization of juvenile flounder and rockfish. Lower weight gain and feed intake in flounder and rockfish fed the diets containing 20% soya were likely due to anti-nutritional factors, rather than transgenic factors in the feedstuffs. Dietary inclusion of GM soya and com at the level tested did not alter the body composition of fishes. Further studies to investigate the effects of GM feedstuffs on health conditions and the development of fishes, as well as those of residue of transgenic fragments in ambient environments and in animals are necessary for safe use of the ingredients in aquaculture.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.2
• /
• pp.141-146
• /
• 2017

New infectious diseases such as MERS have been in need of many measures such as initial discovery, isolation, and crisis response. In addition, the culture of hospitals is changing, such as the general public 's visiting and Nursing Care Integration Services. However, as the qualifications and regulations of medical personnel in hospitals become rigid, overseas such as linens, wastes movements are replacing possible works with robots. we have developed a hospital logistics robot that can carry out various goods delivery within a hospital, and can move various kinds of objects safely to a desired location. In this thesis, we have studied a hospital logistics robot that can carry out various kinds of goods delivery within the hospital, and can move various kinds of objects such as waste, and linen safely to a desired location. The movement of a robot in a hospital may cause a collision between a person and an object, so that the collision must be prevented. In order to prevent collision, it is necessary to recognize whether or not an object exists in the movement path of the robot. And if there is an object, it should recognize whether it moves or not. In order to recognize human beings and objects, we recognize the person with face/body recognition technology and generate the context awareness of the object using 3D Vision image segmentation technology. We use the generated information to create a map that considers objects and person in the robot moving range. Thus, the robot can be operated safely and efficiently.