• Journal of IKEEE
• /
• v.14 no.3
• /
• pp.236-243
• /
• 2010

Power quality mitigation devices play an important role in lots of industrial segments. Although there were many devices available in the market, the selection of an appropriate device specially for voltage sags and interruptions mitigation has been a challenge in the utility and customer for several years. It usually depends on technical and economic characteristics of the device. Nevertheless, most mitigation method is selected by rule of thumb or empirical method. In this paper, the life cycle cost analysis for the probabilistic risk assesment of voltage sag mitigation method is performed using either the deterministic or probabilistic approach. The difference between a deterministic and a probabilistic cost analysis approach is illustrated with five different case studies. This paper not only provides a comparison of life cycle costing of various devices but it also indirectly shows the possible savings due to the mitigation of voltage sags in the form of a project balance chart.

• Structural Engineering and Mechanics
• /
• v.48 no.4
• /
• pp.501-518
• /
• 2013

Apart from thinning of cortical layers, the local bone curvature, varying along bone periphery, modulates ultrasound waves as well, which is however often underestimated or overlooked in clinical quantitative ultrasound (QUS). A dedicated three-dimensional finite element modelling technique for cortical bones was established, for quantitatively exploring and calibrating the effect of local curvature of cortical bone on ultrasound. Using a correlation-based mode extraction technique, high-velocity group (HVG) and low-velocity group (LVG) wave modes in a human radius were examined. Experimental verification using acrylic cylinders and in vitro testing using a porcine femur were accomplished. Results coherently unravelled the cortical curvature exerts evident influence on bone-guided ultrasound when RoC/${\lambda}$ <1 for HVG mode and RoC/${\lambda}$ <2 for LVG mode (RoC/${\lambda}$: the ratio of local bone curvature radius to wavelength); the sensitivity of LVG mode to bone curvature is higher than HVG mode. It has also been demonstrated the local group velocity of an HVG or LVG mode at a particular skeletal site is equivalent to the velocity when propagating in a uniform cylinder having an outer radius identical to the radius of curvature at that site. This study provides a rule of thumb to compensate for the effect of bone curvature in QUS.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.8
• /
• pp.917-920
• /
• 2016

SpSF algorithm is direction-of-arrival estimation algorithm based on sparse representation of incident signlas. Cost function to be optimized for DOA estimation is multi-dimensional nonlinear function, which is hard to handle for optimization. After some manipulation, the problem can be cast into convex optimiztion problem. Convex optimization problem tuns out to be constrained optimization problem, where the parameter in the constraint has to be determined. The solution of the convex optimization problem is dependent on the specific parameter value in the constraint. In this paper, we propose a rule-of-thumb for determining the parameter value in the constraint. Based on the fact that the noise in the array elements is complex Gaussian distributed with zero mean, the average of the Frobenius norm of the matrix in the constraint can be rigorously derived. The parameter in the constrint is set to be two times the average of the Frobenius norm of the matrix in the constraint. It is shown that the SpSF algorithm actually works with the parameter value set by the method proposed in this paper.

• Korean Journal of Construction Engineering and Management
• /
• v.4 no.4 s.16
• /
• pp.182-191
• /
• 2003

The material lift-up and procurement management for high-rise buildings is complex and critical key to the success of projects. It has been hardly managed by the heuristic or rule-of-thumb techniques which are adapted in usual construction building sites. Especially in downtown high-rise residential building project sites, the limit of heuristic management techniques is critical. It has space constraint for materials loading and site transportation especially in finish work phases in which construction period diverse work trades struggle for their own material and manpower transportation. Hence, it is essential to adapt JIT(Just-In-Time) concept in these particular types of building construction project sites. According to the analysis of the case project sites, the communication and flow of relevant information regarding material lift-up and transportation in project sites is the key factor for successful performance. Therefore, this study analyzes the flow and site transportation of the key materials and provides the system, PLUTO(Procurement & Lift-Up for material Transport Optimizing system). This study also applies the system in the case site and verifies the model validation in actual project.

• Journal of Korean Society of Rural Planning
• /
• v.11 no.2 s.27
• /
• pp.51-57
• /
• 2005

It has been well known that soil erosion and sediments from alpine agricultural fields are causing severe water quality and turbidity problems in receiving waters. Also these result in the loss of money because farmers have to buy top soils to provide enough root zone in the following year. Thus, there have been needs to reduce soil erosion and sediment discharge into the stream networks. To accomplish this end, an effective erosion control plans should be developed based on scientific research, not by rule of thumb. The Universal Soil Loss Equation (USLE) has been widely used to estimate the soil erosion in many countries over the years. In this study, the USLE was used to estimate soil erosion potential under different cropping scenarios in HongCheon County, Kangwon. The soil erosion potential for continuous corn cropping was the highest compared with those from continuous potato find average cropping scenarios. This indicates the soil erosion plans need to be established considering cropping system in the field. The Unit Stream Power Erosion-Deposition (USPED) was applied for HongCheon County to estimate soil erosion and deposition areas. The USPED estimated results can be used to complement USLE results in developing effective erosion control plans.

• Journal of Navigation and Port Research
• /
• v.33 no.10
• /
• pp.699-702
• /
• 2009

Currently many vessels determine an overhead obstruction by a rule of thumb based on their draft for maritime navigation. Therefore they doesn't have a good overhead obstruction clearance because vertical position of vessels varies on time by tidal. As a result, it is occurred maritime accidents that the mainmast of vessels is bumped against overhead facilities. And disaster by global warming and rising sea levels have increased casualties. So we feel keenly the necessity of warning system for not an earthquake but disaster wave such a tsunami. This paper analyzes a precise GPS ephemeris for maritime precise positioning to solve these problems. The precise GPS ephemeris provided by International GNSS service gives a difficulty to real-time application because of its sample interval. This paper proposes an effective interpolation method for real-time application, and it analyzes an accuracy of precise GPS ephemeris through an interpolation method.

• Progress in Medical Physics
• /
• v.9 no.4
• /
• pp.195-200
• /
• 1998

Purpose: When an elongated x-ray field is used for treating a patient, the equivalent- field method is commonly used for the output calculation. This study is intended for investigating potential factors such as, beam quality, field elongation ratio, and depth of measurement, which might effect on the applicability of the equivalent square technique for output calculation. The derivation of a 'rule of thumb' for the application criteria of the equivalent-field method is also aimed. Materials and Methods: Three x-ray beams, 4-, 6- and 10-MV, were employed for this study. Width of the rectangular field was ranged from 5-40 cm and the elongation ratio (length/width) 1:0 to 10:0. An elongation effect was measured in a water phantom at three different depths, dmax, 5-cm, and 10-cm. For an elongated field and its equivalent square field, the output factor was measured and the difference in the output factor were examined between two fields. Results and Discussions: As the elongation ratio increases, a larger discrepancy in outputs is observed between the elongated rectangular field and its corresponding equivalent square field. Output was measured larger for an elongated field than for its corresponding equivalent square field and the maximal difference over 10 % was found. The difference was found larger for the smaller field with the same elongation ratio. The effect of the beam quality and the depth of measurement on the output difference was minimal. Conclusion: Based on the study, there is criteria for the application of the method for output calculation. For the combination of long axis and elongation ratio whose relationship satisfies Elongation ratio < (0.48) (Long axis) - 0.5, the equivalent-field method is valid for output calculation within 2 % for the field whose long axis < 25-cm. For other combinations, instead of using the equivalent-field method, direct output measurement is recommended. This criteria can be applied for 4-10 MV x-ray beams up to 10-cm depth.

• Journal of Korea Port Economic Association
• /
• v.34 no.3
• /
• pp.17-52
• /
• 2018

The purpose of this paper is to measure the clustering change and analyze empirical results. Additionally, by using k-means, hierarchical, and mixed models on Asian container ports over the period 2006-2015, the study aims to form a cluster comprising Busan, Incheon, and Gwangyang ports. The models consider the number of cranes, depth, birth length, and total area as inputs and container twenty-foot equivalent units(TEU) as output. Following are the main empirical results. First, ranking order according to the increasing ratio during the 10 years analysis shows that the value for average linkage(AL), mixed ward, rule of thumb(RT)& elbow, ward, and mixed AL are 42.04% up, 35.01% up, 30.47%up, and 23.65% up, respectively. Second, according to the RT and elbow models, the three Korean ports can be clustered with Asian ports in the following manner: Busan Port(Hong Kong, Guangzhou, Qingdao, and Singapore), Incheon Port(Tokyo, Nagoya, Osaka, Manila, and Bangkok), and Gwangyang Port(Gungzhou, Ningbo, Qingdao, and Kasiung). Third, optimal clustering numbers are as follows: AL(6), Mixed Ward(5), RT&elbow(4), Ward(5), and Mixed AL(6). Fourth, empirical clustering results match with those of questionnaire-Busan Port(80%), Incheon Port(17%), and Gwangyang Port(50%). The policy implication is that related parties of Korean seaports should introduce port improvement plans like the benchmarking of clustered seaports.

• Korean Journal of Construction Engineering and Management
• /
• v.21 no.4
• /
• pp.62-71
• /
• 2020

Various studies on program management have been attempted due to recent changes in the environment of the construction market, and the importance of closure phase in each phase of the construction program is increasing. However, the reality is that the related research is insufficient and the field has been managed in a rule of thumb according to individual capabilities. Therefore, in order to successfully close the construction program and enhance satisfaction of stakeholders in the closure phase of the construction program, the key stakeholders were identified using the Power and Interest Matrix. The relative importance of the closure phase process was analyzed using AHP analysis method. It was also verified through on-site surveys and interviews about the proposed importance of the closure stakeholder and the relative importance of the process. It is expected that this study will increase the satisfaction of stakeholders and contribute to a successful closure if the user puts a lot of resources into the process that has a high priority in the closure phase of the construction program proposed in this study.

• Quality Improvement in Health Care
• /
• v.10 no.1
• /
• pp.58-76
• /
• 2003

Background : Aim of this study is focused on the analysis of the needed abilities of medical representatives resulting in building up the market and increasing sales. It is to propose methods to increase this ability ensuring continuous growth in market share and profit. Methods : A survey was conducted between January 6 and May 31, 2003. Using SPSS(Version 10.0), the collected data was analyzed by Hotelling T2, factor analysis. Some hypotheses were selected to include the conclusion. Some questionnaires for physicians working in hospitals or clinics and the medical representatives working in a pharmaceutical company were created and asked to them to either prove or reject those hypotheses. The results were analyzed to find the primary factors that effect the interactions between physician and the medical representatives. These factors were also studied along with the theoretical research based on published references. Results : The results were as follows. The main reasons for the physician to meet with a medical representatives were collection of product informations needed for patient treatment and collection of informations on current medical issue and as well as personal interests. The main parameters by which physicians evaluate the medical representatives are human relationship including sincerity and manners and supply of accurate and unbiased information on products. Overall, the medical representatives' perception on the importance of medical knowledge and ability to deliver it are lower than that expected by physicians. Conclusion : Medical and pharmaceutical companies' environment are changed rapidly. And those changes forced medical representatives to set new roles and competency. In order to drive away from the past 'rule of thumb' and 'adaptation to circumstance', optimal method and systemic development to train and support the medical representatives should be quipped. They will help medical representatives to be specialists in medical knowledge and to understand the exact need of health care professions. Product competitiveness will be increased and eventually successful business can be achieved through it.