• 한국연소학회:학술대회논문집
• /
• 1999.10a
• /
• pp.129-138
• /
• 1999

In this paper, our main issue is that establishing the control procedure of continuous gas flow rate according to combustion fan RPM. For this, first, we decide the optimum operating condition of gas swirl burner through analysis of combustion characteristics - thermal efficiency, combustion efficiency and exhaust gases such as CO, $CO_{2}$, $O_{2}$, $NO_{x}$ and THC. Second, fuel gas flow rate of gas valve is decided with considering excess air ratio and combustion fan RPM is decided by the target of combustion air flow rate. Finally, experimental operating equation is acquired by regression for gas valve and combustion fan. This equation is the control equation of continuous gas flow rate and always gas flow rate is decided by combustion fan operating RPM.

• Proceedings of the KIPE Conference
• /
• 2012.11a
• /
• pp.129-130
• /
• 2012

본 논문에서는 3축 가속도 센서의 부착 방법과 위치에 따른 진동 신호의 주파수 특성을 분석하였다. 날개 하나가 깨진 환풍기를 철제 기둥에 나사로 고정하고 회전수를 50rpm, 1710rpm, 2400rpm으로 각기 달리하여 진동을 발생 시켜 가속도 센서의 부착 방법과 위치에 따른 진동 신호를 측정하고 비교하였다. 3축 가속도 센서를 측정하기 위한 측정 소프트웨어를 설계 제작하였으며, 센서의 진동을 비교한 결과 실험에 사용된 회전수에서는 각각의 부착 방법보다는 부착 위치에 따른 진동의 차이가 있는 것으로 나타났다.

• Tribology and Lubricants
• /
• v.6 no.2
• /
• pp.43-49
• /
• 1990

The Dynamic Behavior in line contacts between the vane tip and camring in an oil hydraulic vane pump with intravanes has been investigated. Variations of the radial acting force of a vane were calculated from previously measured results of dynamic infernal pressure in four chambers surrounding a vane, and variations of the behavior were estimated in both the rotational speed range from 1200 to 2700 rpm and in the delivery pressure range from 10 to 21Mpa. The results indicate the variations of the radial acting force. Under the standard operating condition (to 14 Mpa, 1800 rpm), the radial acting force on the vane is governed by internal dynamic pressures, but it is more influenced by rotating speed at higher than 2000 rpm relatively.

• Progress in Superconductivity and Cryogenics
• /
• v.2 no.1
• /
• pp.7-13
• /
• 2000

A rotating cryogenic system was designed similar to the cooling system for the rotor of a superconducting generator. The experimental rotor has an inner vessel which simulates the winding space of an actual superconducting rotor, and a torque tube of comparable design. This paper describes the evaluation of the total heat leak into the inner vessel that leads to the study of the heat transfer characteristic of the rotating cryogenic system. To examine the insulation performance of the experimental rotor. temperature was measured at each part of the system at various rotaing speeds from 0 rpm to 600 rpm. Total heat leak into the inner vessel was calculated by measuring the boil-off rate of liquid helium. Conduction heat leak to the inner vessel was obtained by the vent tube, and radiation heat leak was calculated by subtracting the conduction heat lent from the total heat leak. There seemed to be no rotaional dependency of total heat leak at least up 600 rpm.

• 한국생물공학회:학술대회논문집
• /
• 2000.11a
• /
• pp.725-728
• /
• 2000

The effects of agitation rate and agitation time on the synthesis of sphingosome were studied. As increase in the agitation rates 4,000, 6,000, 8,000, 10,000 and 12,000 rpm the viscosity of sphingosome were decreased. The most sufficient agitation rate was 8,000rpm for which micell viscosity and stability. The effect of agitation time on the sphingosome viscosity and stability was investigated by changing the agitation times 2, 4, 6, 8 and 10 minute at 8,000rpm. 4 minute was the most sufficient for the viscosity and stability. The sphingolipid activity of cutaneous wound healing in impaired mice was examined. As a result, we could prove that phytosphingosine-HCl medically worked on wound healing well. For the phytosphingosine-HCl, it was found that the experimentally determined medical action more effective than that of tetra-acetylphytosphingosine.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.1
• /
• pp.45-54
• /
• 2003

Turbo compressor needs high speed rotation of impeller in structure, high rated gearbox and conventional induction motor. This mechanical system increased the moment of inertia and mechanical friction loss. Resently, the study of turbo compressor applied super high speed motor and drive, removing gearbox made its sire small and mechanical friction loss minimum. This paper describes the implementation of the vector control schemes for a variable-speed 131㎾ PMSM(Permanent Magnet Synchronous Motor) drive in super-high speed application.

• Journal of Environmental Health Sciences
• /
• v.17 no.1
• /
• pp.32-38
• /
• 1991

Airborne suspended particulate concentration in drilling sites of underground coal mines in Taebaek area was evaluated. And respirable coal dust exposure level was evaluated. Airborne suspended particulate mass include total suspended particle(TSP) and thoracic particle(TPM). TSP (by open-face filter holder) and TPM(by elutriator) concentration were determined by low volume air samplers. Personal air samplers were attached to the coal workers including drillers, coal cutters, and their assistants. Normality and log-normality of TSP, TPM, and respirable dust(RPM) concentration were tested by Kolmogorov-Smirnov one-sample test. Differences of means of TSP, TPM, and RPM concentration were tested by paired t-test. Relation between TSP, TPM, and RPM with pairs were tested by regression test and Pearson's correlation.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.396-400
• /
• 2003

This paper has studied thermal characteristics of machine tool to develope high speed spindle and optimum design condidering the thermal deformation. Comparing the test data of temperature measurement and structural analysis data using FEM, we verifiedthe test validity and predicted thermal deformation, influence of spindle generation of heat, and established cooling system to prevent the thermal deformation. 1) The temperature rise of spindle system depends on increasing number of rotation and shows sudden doubling increment of number of rotation over 7,000rpm. 2) Oil jacket cooling can be effective cooling method below 8,000rpm but, over 8,000rpm, it shows the decrement of cooling effect. 3) Comparing FEM analysis results and revolution test results, we can confirmn approximate temperature change consequently, it is possible to simulate temperature rise and thermal distribution on the inside of spindle system. 4) We can confirm that simulated approach by FEM analysis can be effective method in thermal-appropriate design..

• 한국가시화정보학회:학술대회논문집
• /
• 2004.11a
• /
• pp.48-51
• /
• 2004

Chemical Mechanical Polishing(CMP) is popularly used in production of semiconductor because of large area polishing ability probability of improvement for more integrated circuit. However, present CMP processing causes some non-uniformity errors which can be critical for highly integrated circuit. Previous studies predict that flow-field of slurry during CMP can create non-uniformity, but no quantitative measurement has conducted. In this study, using PIV, slurry velocity flow-field during CMP is measured by changing the ratio of RPM of pad and carrier with tuned PIV system adequate for small room in CMP machine and Cabot's non-groove pad Epad-A100. The result show that velocity of slurry is majorly determined by pad-rpm and the ratio of between carrier and pad rpm make some changes in streamlines.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.3
• /
• pp.420-427
• /
• 2006

This paper describes design and characteristic analysis of the 200[kW], 3000[rpm] induction motor for gearless turbo machine. It was designed by the loading distribution method and the results of characteristics obtained by the equivalent circuit method are compared with the results of circle diagram. To verify the validation of design 2D finite element method is used and also 3D finite element method is used to calculate the current density curve of the rotor bars when they are broken.