• Journal of Biosystems Engineering
• /
• v.30 no.6 s.113
• /
• pp.354-359
• /
• 2005

This is a fundamental study to develop a bio-gas utilization technology using livestock manure. Especially, this study was carried out to develop an engine using bio-gas. A bio-gas engine was designed and manufactured by modification of a diesel engine of 3 cylinders powering 13.31 kW/2800 rpm, changing the fuel supplying system fit for bio-gas. The result showed that, when the Air/Fuel ratio was controlled with fixed spark timing, the power of biogas-fueled engine is about $10.6{\~}14.6\%$ lower then that of LNG-fueled engine because of low volumetric efficiency. The engine output and torque was $11.85{\~}13.3$ kW, $39.5{\~}40.8\;N{\cdot}m$, respectively at the engine speed of 2600 rpm. Bio-gas consumption rate was 260.20 g/kW/hr, 315.20 g/kW/hr in engine speed or 1000 rpm, 2800 rpm, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5082-5088
• /
• 2015

In this paper, durability test of 1000cc level gasoline engine has been carried out. Durability test set total 300 hours and WOT condition. Engine torque, power, fuel consumption, blow-by gas flow rate, and oil pressure are measured to analyse performance variation by time. As a result, engine performance of high rpm range gradually reduced by time but for relatively low rpm range shows stable performance. Blow-by gas flow rate shows 0.4% of averaged induction air flow rate, which is excellent rate for 1000cc level gasoline engine. Engine torque and fuel consumption data show the break-in upto 100 hours and aging trend after that. After 300 hours, engine is disassembled and each part is checked for the damage or crack.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.4
• /
• pp.132-138
• /
• 2007

Experimental results of pulsating pressure behavior inside a chamber have been confirmed by computational work. Inside-cylinder pressure shows unstable condition at low rpm. This is caused by plate-type suction valve. It has effect up to inlet of the chamber. But trembling phenomenon is reduced as the pressure is enlarged by increasing the rpm. Result comparison between experimental and numerical analysis shows pulsation reduction is affected by the chamber. We can confirm that compressible effect of the working flow is shown at chamber inlet by increasing rpm. On the other side, this effect is declined at chamber outlet by increasing rpm. It means outlet pressure is going on balance with atmosphere pressure. Buffer plate-type chamber has efficiency of pulsation flow reduction.

• Korean Journal of Food Science and Technology
• /
• v.30 no.1
• /
• pp.118-124
• /
• 1998

Dehulled cowpea was microparticulated and coarse fractions and fine fractions were collected by air classification at air classifying wheel speed (ACWS) of 15,000 rpm, 12,000 rpm and 9,000 rpm, respectively. Protein content in fine fraction after air classification was 2 times higher than that of microparticulated cowpea, emulsion capacity was about 3 times than coarse fraction. The coarse fraction of the highest viscosity on the gelatinization properties were detected by amylograph, was C-3 (9,000 rpm coarse)fraction. The majority of microparticulated cowpea particles were oval shaped starch and the rest of them were indeterminate minute particles which had some sharp corners. As an application test, microparticulated cowpea and coarse fraction (C-3) were used for mook (Korea traditional starch jelly) preparation and the wet milled cowpea starch was compared as a control. Some impurities induced discoloring was detected by sensory evaluation but after washing, it made no difference in sensory scores between washed starch and the control cowpea mook. And also syneresis of washed cowpea was less than control. At the above result, it can be to recovery about 85% of cowpea starch using microparticulation/air classification technology.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.49-53
• /
• 2004

LabVIEW is mostly preferred to use in experiment, measurement and control as one of the useful thing in America and Europe. So, We tried performance experiment of a single-stage closed-type centrifugal pump by using the LabVIEW. The pump rpm and the shaft torque are measured by rpm sensor and torque sensor The test pump's maximum rpm, head, kW are 1,750, 13m, and 1.5kW, respectively The casing is made up with transparency acrylic for confirmation the flow patterns. We installed experimental equipment for air water two phase flow. This paper tries to analyze the single-phase flow characteristics through this air water two phase flow experimental apparatus. The performance results of a single-stage closed-type centrifugal pump satisfied reappearance and coincide well with head and coefficients according to the change of rpm.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.11a
• /
• pp.83-86
• /
• 2006

This study investigates engineering properties of concrete using recycled coarse aggregated manufactured by bar-crusher. Test showed that Bar-crusher(S) had more effective results at fresh state than cone-crusher(C) and impact-crusher(I). In case of specimens manufactured by S, increase of spindle velocity, incorporating ratio of recycled aggregate and maximum size of aggregate inclined fluidity. As for the hardened concrete, compressive strength of specimens by C or I exhibited lower value than that of S. In addition, specimens using recycled aggregate manufactured by 400rpm and 500rpm of spindle velocity showed less than 10% reduction rate of strength, which is not significant reducing value. It is found that 500rpm of the spindle velocity had the best strength performance, while 600rpm was the worst. Strength value of specimens decreased as incorporating ratio of recycled aggregate inclined, but the strength value of most specimens exhibited less than 10% of reducing rate, assuming favorable result, only at less than 25% incorporating ratio of recycled aggregate.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.2
• /
• pp.111-117
• /
• 2016

The cutting performance of a developed small-angle spindle tool was investigated with Al6061 using a TiAlN coated high-speed steel end mill. Up-cut and down-cut processes in a milling machine were carried out at the range of 1000-4000 rpm for spindle speed and 50-300 mm/min for feed rate. As a result, the highest cutting force in the Fx direction was obtained from the up-cut process when the spindle speed was 1000 rpm and the feed rate was 100 mm/min. In the Fy direction, the highest cutting force appeared in the up-cut process at a feed rate of 250 mm/min at the same spindle speed. Conversely, the lowest cutting force came out in the up-cut process at a spindle speed of 4000 rpm and a feed rate of 50 mm/min. As for surface finish, the finest surface roughness was obtained as Ra 0.7642 um at a spindle speed of 4000 rpm and a feed rate of 50 mm/min. Consequently, given the cutting performance of the developed small-angle spindle tool, we conclude that its use in industrial practice is feasible.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.8 no.1
• /
• pp.50-61
• /
• 2000

The effects of an inserted coil on flow . patterns and heat transfer performance for a horizontal rotating heat pipe have been studied experimentally. Especially, the present study is to see an internally inserted helical coil inside a RHP would lead to the same kind of results as internal fins. Visualization test conducted for an acryl tube, charged water with at a volumetric rate of 20%. When the flow kept pool regime at a low rpm(less than 1,000rpm), the movement of coil forced the water to flow in axial direction. But this pumping effect of coil disappeared, when the pool regime changed to annular one which could be created by increasing rpm. The pumping effects for RHP with an inserted coil resulted in the enhancement in both condensation heat transfer coefficient and heat transport limitation, as obtained in case of using internal fins. But all these effects became negligible in the range of higher rpm(above 1,000-1,200) with the transition of flow regime to annular flow.

• Korean Journal of Crystallography
• /
• v.13 no.1
• /
• pp.41-47
• /
• 2002

La/sub 1-x/Ca/sub x/MnO₃ manganese oxide were grown using the floating zone image furnace with halogen lamps as heat source. The growth condition was 4∼6 mm/hr growth rate in air atmosphere, 45∼50 rpm and 20∼25 rpm of rotation rate of feedrod and growing crystal, respectively. Characterization analyses of the crystal were carried out using XRD, SEM, and EPMA. Orientation of crystal was determined using EBSD. The electromagnetic properties were measured with Quantum Design PPMS by 4 point probe method and resulted MR value of 462% at 215 K.

• Journal of Fisheries and Marine Sciences Education
• /
• v.29 no.2
• /
• pp.586-592
• /
• 2017

This study analyzed the effect of four control factors, RPM, load, EGR rate and cooling water temperature on the exhaust emissions of the small DI diesel engine. The amount of NOx and smoke emissions were measured through experiments for three levels of four control factors according to orthogonal array table, and the effect of four factors on NOx and smoke emissions was analyzed quantitatively. The main results obtained in this study are summarized as follows: 1. RPM, load and EGR rate have a great influence on NOx and smoke emissions, and the effect of cooling water temperature is negligible. 2. As RPM and load increases NOx emission increases and decreases sharply as the EGR rate increases. 3. Smoke emission decreases or increases randomly according to RPM and load, but increases sharply in proportion to the EGR rate. 4. EGR rate has the greatest effect on NOx and smoke emissions by more than 60% of contribution to variance, especially in the case of NOx emission, EGR rate represents a significant result even under the confidence level of 99% on ANOVA.