• Structural Engineering and Mechanics
• /
• 제61권2호
• /
• pp.221-230
• /
• 2017

In this paper, we investigated the propagation of thermoelastic surface waves in fibre-reinforced anisotropic general viscoelastic media of higher order of nth order including time rate of strain under the influence of rotation. The general surface wave speed is derived to study the effectsof rotation andthermal onsurface waves. Particular cases for Stoneley, Love and Rayleighwaves are discussed.The results obtained in this investigation are more general in the sense that some earlier published results are obtained from our result as special cases. Our results for viscoelastic of order zero are well agreed to fibre-reinforced materials. Comparison was made with the results obtained in the presence and absence of rotation and parameters for fibre-reinforced of the material medium. It is also observed that, surface waves cannot propagate in a fast rotating medium.Numerical results for particular materials are given and illustrated graphically. The results indicate that the effect of rotation on fibre-reinforced anisotropic general viscoelastic media are very pronounced.

• 대한기계학회논문집B
• /
• 제27권5호
• /
• pp.628-634
• /
• 2003

We present numerical and experimental results of periodic flows inside a rectangular container under a background rotation. The periodic flows are generated by changing the speed of rotation periodically so that a time-periodic body forces produce the unsteady flows. In numerical computation, a parallel-computation technique with MPI is implemented. Flow visualization and PIV measurement are also performed to obtain velocity fields at the free surface. Through a series of numerical and experimental works, we aim to clarify, if any, the fundamental reasons \ulcornerf discrepancy between the two-dimensional computation and the experimental measurement, which was detected in the previous study for the same flow model. Specifically, we check if the various assumptions prerequisite for the validity of the classical Ekman pumping law are satisfied for periodic flows under a background rotation.

• 소성∙가공
• /
• 제12권8호
• /
• pp.730-737
• /
• 2003

Extensive studies have been conducted for reducing the residual stresses and birefringence in injection-molded optical disk substrate Flow-induced and thermally-induced stresses and birefringence have been found as two main sources during injection molding process. However, high speed rotation also induces extra stresses and birefringence in real operation of disk drives. In the present paper rotation-induced in-plane birefringence has been measured and presented for CD and DVD substrates at different radial position. About 10 - 15 nm of extra retardation in one pass has been measured up to 4,800 rpm. The distribution of extra rotation-induced birefringence will be valuable data for designing an optimal optical disk substrate. Finally, experimental results were compared with the extra stresses calculated from simple formulation.

• 한국자동차공학회논문집
• /
• 제25권3호
• /
• pp.273-286
• /
• 2017

We develop an inspection method for bearing faults with a rapid change in the rotation speed and present indexes for the pass/fail inspection. At the end of line, impulse noises generated by the operation of machines and conveyors may distort the inspection results. In this paper, we present robust inspection indexes for bearing faults under impulse noises, by taking into account fault signals having pulse train. Using logistic regression, we optimize the pass/fail criterion for each index and evaluate the performance of the inspection indexes based on the total error rate.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.676-681
• /
• 2003

In this paper, we investigated the disc warping in high-speed slim-type optical disc drive. Recently, the information storage devices are increasing track density and higher rotation speed to enhance their recording capacity and their data transfer rate. Generally, ODD used in the Lap-top Computer has small inner space. So, the flow instability of inner space is rapidly increased as its higher rotation speed. An extreme case, the flow instability causes the malfunction of readout at pick-up of drives. The experiments and numerical analysis were carried out for several cases, the result shows the influence of airflow to the disc warping.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1999년도 유체기계 연구개발 발표회 논문집
• /
• pp.33-40
• /
• 1999

Upgrade development of a high pressure ratio centrifugal compressor in marine engine turbochargers is presented. A new matched operating point at increased speed of rotation was determined through system cycle analysis using the exisitng test data of turbine performance. Under some severe restrictions for geometric parameters, the state-of-the-art methods of both aerodynamic design and CFD analysis were applied, in which only an impeller, a vaned diffuser and some part of casing wall were modified. Prototype hardware was fabricated and assembled for system performance tests. Excellent performance in pressure ratio and efficiency was obtained over whole speed region. Reduced surge and choke margin was, however, observed at design speed of rotation.

• 한국식품저장유통학회지
• /
• 제18권5호
• /
• pp.627-635
• /
• 2011

본 연구는 표면 세척 시스템을 이용하여 유자의 미생물과 잔류농약 제거 효과를 살펴보았다. 선행 연구로 오징어 먹물을 제거 효과를 보기 위해 스프레이 회전 속도 0.11, 0.42, 0.73 m/s, 수압 0.6, 0.9, 1.2 MPa과 컨베이어 속도 0.046, 0.092, 0.138 m/s 으로 세척 조건을 달리하였다. 오징어 먹물 제거 실험 결과 먹물 제거 효율은 컨베이어 속도와 분사 노즐 회전수와는 높은 상관관계를 나타내었으며 수압의 조건에서는 반응표면 분석 결과 0.9 MPa에서 가장 제거율이 높게 분석되었다. 이에 미생물과 잔류농약 제거률 실험의 위해 세척 조건으로 수압을 0.9 MPa로 고정하였으며 스프레이 회전 속도(0.11, 0.42, 0.73 m/s)와 컨베이어 속도(0.046, 0.092, 0.138 m/s)를 달리하여 수행하였다. 미생물은 컨베이어 속도 2.76 m/min 일 때 스프레이 회전속도 0.43과 0.73 m/s에서 각각 2.20, 2.05 log CFU/g 수준 감소하여 가장 높은 감소율을 나타내었다. 또한 스프레이 회전속도 0.11 m/s와 컨베이어 속도 0.138 m/min을 제외한 모든 처리구의 미생물 제거효과는 수도수 처리보다 높았다. 잔류농약 실험 결과 컨베이어 속도가 느릴수록, 분사노즐 회전수가 많을수록 제거효과가 높았으나 spirodichlofen, deltamethrin, benomyl, thiophanate-methyl과 acequinocyl 의 경우 컨베이어 속도 0.046 m/s에서 분사노즐 0.42 m/s이상에서 처리구들 간에 유의적인 차이를 보이지 않았다. Benomyl과 thiophanate-methyl 의 잔류 농약은 컨베이어 속도 0.092 m/s 이하의 조건에서 90% 이상 제거되었다. 이상의 결과에서 표면 세척 시스템의 조건을 컨베이어 속도 0.092 m/min 이하, 노즐 회전수 0.043 m/s 이상에서 세척 시 유자의 미생물과 잔류농약을 효율적으로 제거할 수 있을 것으로 판단된다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권1호
• /
• pp.30-41
• /
• 2006

This paper shows mechanical Properties and behaviors of macrostructures for specimens welded by F.S.W according to welding conditions and tool dimensions with $6.35mm_t$ aluminum 7075-T651 alloy plate. It apparently results in defect-free weld zone in case transition speed was changed to 15mm/min 61mm/min and 124mm/min under conditions of tool rotation speed such as 800rpm. 1250rpm and 1600rpm respectively with tool's Pin diameter 40mm and 60mm. The optimum mechanical property, ultimate stress,${\sigma}_Y=470Mpa$ is obtained at the condition of 124mm/min of travel speed with 800rpm of tool rotation speed using full screw type pin. shoulder dia. $20{\phi}mm$ pin dia. $6{\phi}mm$ and pin length 6mm. The full-screw type and the half-screw type pin shows the similar behaviors of weldability. It is found that the size of nugget is depended on tool transition speed and tool dimension by macrostructures of the cross section of weld zone.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.348-358
• /
• 2005

This paper showed mechanical properties and behaviors of macrostructures for specimens welded by F.S.W according to welding conditions and tool with 6.35$mm_t$ aluminum 7075-T651alloy plate. It resulted in defect-free weld zone in case tool rotation speed was 800rpm, 1250rpm and 1600rpm respectively that transition speed was changed to 15mm/min, 61mm/min and 124mm/min with tool's pin diameter 4${\Phi}$mm and 6${\Phi}$mm. The optimum mechanical property, ultimate stress,${\sigma}_Y$=470Mpa was obtained at the condition of 124mm/min of travel speed with 800rpm of tool rotation speed using full screw type pin, shoulder dia. 20${\Phi}$mm, pin dia.6${\Phi}$mm and pin length 6mm. The full-screw type and the half-screw type pin showed the similar behaviors of weldability. It is found that the size of nugget was depended on tool transition speed and tool dimension by macrostructures of the cross section of weld zone.

• 한국운동역학회지
• /
• 제18권1호
• /
• pp.53-62
• /
• 2008

본 연구는 플랫폼 다이빙 종목 205B를 3차원 영상분석을 통하여 운동학적 분석을 하였다. 총소요시간은 평균 $1.112{\pm}0.12s$로 나타났으며 여유 있는 연기를 수행하기 위해 많은 소요시간을 확보하여야 할 것으로 사료된다, 이지시 신체중심의 높이는 평균 88.8cm이며 수평거리는 144.8cm, 수평, 수직속도는 평균 1.08m/s, 1.3m/s로 나타났으며, 회전동작은 높은 위치에서 수행해야 하며, 수평거리는 짧아야 입수자세에 유리 할 것으로 판단된다. 하지분절의 속도변화는 이지 시 속도가 감소한 이후 회전이 이루어지는 시점까지 상승하며 이지 순간에는 회전보다는 점프동작에 더 큰 영향을 미치며, 신체중심을 축으로 회전동작으로 이어지고 속도가 상승하는 것으로 판단된다. 몸통각속도는 이지 시에 크게 나타났는데, 이는 상 방향으로 점프하여 회전에 필요한 힘을 얻기 위해 상체분절을 최대한 곧게 펴고 신체중심을 높게 유지하여 도약을 해야 효과적인 동작을 수행 할 수 있기 때문으로 사료된다.