• Journal of Korean Society of Forest Science
• /
• v.103 no.3
• /
• pp.402-407
• /
• 2014

In this study, Italy poplar(Populus euramericana) was selected for test specimen to measure cutting power when it harvested. The experiment has been controlled as three levels of feed rate (0.41, 1.25 and 2.5 m/s), sawing speed (800, 1,000 and 1,200 rpm), and the five levels of root collar diameter (50, 70, 90 and 110, 130 mm). The harvested volume after 3 years (root collar diameter 50 mm) was 10.5 tons, which falls short of the target amount of biomass is 20~30 ton/ha. In addition, the biomass amount of diameter 90 and 110 mm which reached the target amount were estimated to be 23.5 and 32.5 ton/ha respectively. As a result of experiment, it was found out that power of 128.2 and 175.8 W are consumed in case of cutting with the feed rate of 0.41m/s and minimum sawing speed (800 rpm) respectively. With the working area of 0.3 ha/h, it is considered to present working capacities of 16.5 and 22.8 ton/h respectively. The power consumed at the feed rate of 1.25 m/s is estimated to be 113.8 and 153.7W respectively and working capacity in a working area of 1 ha/h is estimated to be 23.5 and 32.5 ton/h. The power consumed at the feed rate of 2.5 m/s is estimated to be 119.8 and 166.9 W respectively and working capacity in a working area of 2 ha/h is estimated to be 47.0 and 65.5 ton/ha respectively. Therefore, the power source of harvest machine at the feed rate of 1.25, 2.50 m/s and sawing speed of 800 rpm shall be selected as it can process the target amount of estimated biomass.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1116-1122
• /
• 2009

As a result of this study, we reached the following conclusions. With appropriate setting of oil pressure and flow rate, it operated same rotation speed with existing cooler by electrical transmission. In initial operation, a temperature of a cold storage is lower rapidly. As an internal temperature of a cold storage is lower, a decreasing rate of temperature is lower. As a result of comparing the both type, the cooler of oil pressure type showed the following results. The decreasing rate of temperature was more faster and shorter operating time was more shorter than existing cooler of electric type. The actual case of a cold storage, the cooler of oil pressure type can prevent quality deterioration and decrease power consumption. As an internal temperature of a cold storage is lower, power consumption increased rapidly, the oil pressure type showed lower power consumption. COP of two of these types decreased continuously as the internal temperature of a cold storage being reach setting temperature, and that of oil pressure type showed higher amount about 25%. As a setting temperature is lower, the number of refrigerator's operating times are less and operating time is longer, so power consumption is increased in the maintenance of a cold storage's internal temperature, power consumption of hydraulic type showed lower amount about 21~25% in two of these types.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.1
• /
• pp.181-194
• /
• 2013

Landslides are known as gravitational mass movements that can carry the flow materials ranging in size from clay to boulders. The various types of landslides are differentiated by rate and depositional features. Indeed, flow characteristics are observed from very slow-moving landslides (e.g., mud slide and mud flow) to very fast-moving landslides (e.g., debris avalanches and debris flows). From a geomechanical point of view, shear-rate-dependent shear strength should be examined in landslides. This paper presents the design of advanced ring-shear apparatus to measure the undrained shear strength of debris flow materials in Korea. As updated from conventional ring-shear apparatus, this apparatus can evaluate the shear strength under different conditions of saturation, drainage and consolidation. We also briefly discussed on the ring shear apparatus for enforcing sealing and rotation control. For the materials with sands and gravels, an undrained ring-shear test was carried out simulating the undrained loading process that takes place in the pre-existing slip surface. We have observed typical evolution of shear strength that found in the literature. This paper presents the research background and expected results from the ring-shear apparatus. At high shear speed, a temporary liquefaction and grain-crushing occurred in the sliding zone may take an important role in the long-runout landslide motion. Strength in rheology can be also determined in post-failure dynamics using ring-shear apparatus and be utilized in debris flow mobility.

• Journal of the Korean Electrochemical Society
• /
• v.16 no.1
• /
• pp.52-58
• /
• 2013

In order to overcome the cost issue for commercialization of polymer electrolyte membrane fuel cell (PEMFC), this research was conducted for replacing platinum cathode catalyst with non-precious metal catalyst. The non-precious metal catalyst (Co-PANI-C) was synthesized by the simple reduction method with polyaniline (PANI), carbon black, and cobalt precursor without any heat treatment. Characterization of new Co-PANI-C composite catalysts was done by the measurement of X-ray diffraction (XRD) and thermogravimetric analysis (TGA) for structure analysis and performed by rotating disk electrode (RDE) and rotating ring disk electrode (RRDE) for electrochemical analysis. As a result, Co-PANI-C catalyst showed 60 mV lower on-set potential for oxygen reduction reaction (ORR) than Pt/C catalyst, but the overall reduction current of Co-PANI-C catalysts by ORR was still smaller than that of Pt/C. In addition, the ORR behavior of Co-PANI-C catalysts depending on the rotation speed of electrode and the stability of Co-PANI-C catalyst under potential cycling and the performance of fuel cell conditions are also discussed.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.3
• /
• pp.63-69
• /
• 2013

This paper related with the performance of SE-MMA (Signed-Error MMA) that is the reduction of computational operation number in algorithm than MMA blind eualization algorithm which are possible to elimination of intersymbol interferance in the band limited and time dispersive nonlinear communication channel. In MMA algorithm which are possible to reduction of amplitude and phase rotation by intersymbol interference that is occurred in channel without using the training sequence, it uses the error signal that is the difference of the equalizer output and constant modulus, the statisticlly characteristic of transmitted signal. But in SE-MMA, it uses the polarity of the error signal, then it is possible to reduce the updating the tap coefficient and to simplify the H/W implementation. The computer simulation were performed in order to compare the performance of SE-MMA and conventional MMA algorithm. For this, the recovered signal constellation that is the output of the equalizer, the convergence performance by MSE, MD (maximum distortion) and residual isi characteristic learning curve, SER were used. As a result of simulation, the SE-MMA has more fast convergence speed than the MMA. But in the other index after reaching the seady state, it gives more worst performance values in the used index.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.2
• /
• pp.136-146
• /
• 2013

In this paper, the residual delay compensation algorithm is proposed for FX-type KJJVC. In case of initial version as that design algorithm of KJJVC, the integer calculation and the cos/sin table for the phase compensation coefficient were introduced in order to speed up of calculation. The mismatch between data timing and residual delay phase and also between bit-jump and residual delay phase were found and fixed. In final design of KJJVC residual delay compensation algorithm, the initialization problem on the rotation memory of residual delay compensation was found when the residual delay compensated value was applied to FFT-segment, and this problem is also fixed by modifying the FPGA code. Using the proposed residual delay compensation algorithm, the band shape of cross power spectrum becomes flat, which means there is no significant loss over the whole bandwidth. To verify the effectiveness of proposed residual delay compensation algorithm, we conducted the correlation experiments for real observation data using the simulator and KJJVC. We confirmed that the designed residual delay compensation algorithm is well applied in KJJVC, and the signal to noise ratio increases by about 8%.

• The Korean Journal of Applied Statistics
• /
• v.31 no.4
• /
• pp.427-446
• /
• 2018

Korea will have a super-aged society within only 30 years according to the United Nations' definition of an aging society and the statistics on Korea's Population projections (2016), indicates that Korea has the fastest ageing speed in the world. There is a lack of data on long-term time-series data on death as related to pension and welfare policies compared to the rapid rate of aging. This paper estimates life expectancy over 245 years (from 1955 to 2200) through past and future forecasts as well as compares the expected life expectancy of the synthetic cohort and the real cohort. In addition, an international comparisons were made to understand the level of aging in Korea. Estimates of the back-projection period were compared with previous studies and the LC model to improve accuracy and objectivity. In addition, the predictions after 2016 reflected the declined mortality rate effect of Korea using the LC-ER model. The results showed an increase in life expectancy of about 30 years over 60 years (1955-2015) with an expected life expectancy of the real cohort over the second century (1955-2155) higher than the synthetic cohort. The comparative advantage of life expectancy of real cohorts was confirmed to be a common trend among comparative countries. In addition, Japan and Korea have a higher life expectancy and starting from 85 to 90 years old, all comparative countries show that the growth rate for the life expectancy of synthetic and real cohorts is less than previous years.

• Archives of design research
• /
• v.18 no.4 s.62
• /
• pp.139-146
• /
• 2005

Animation works have been peformed by the objective sensitivity and experience so far. Software designs have been also manufactured based on intelligent data because they are easy to objectify and digitalize. In contrast, there are many elements, which human senses are hard to objectify and digitalize. This study investigates how to digitalize and objectify human senses and how to use them as the quantitative data and its subject is a flying path. In the experiment, this study collects some sensitive words for how human beings express the living path. The evaluation words for sensitivity through the collected sensitive words are extracted and the sketch images for the flying path are collected from the extracted evaluation words for sensitivity. Based on the collected sketch images, the samples of real moving image, which are the core of this study, are manufactured. Then, quantification theory III and I are used in order to analyze the correlation between the sensitive words representing the flying path and the samples of moving image. As a result, this study can figure out the structure of sensitive words and the samples of moving image and analyze the physical stimulating elements for the flying path. The flying path corresponds to the path that the object has passed. Some unique sensitive words are expressed by means of interacting some sensitive stimulating elements after looking at such a path. There are some elements that stimulate the senses and they include the physical elements such as speed, rotation, pattern and length of arc. The purpose of this study is to objectify and quantify the animation works that are created by animators' subjective thought and experience and to use them in animation works in the future.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.4
• /
• pp.423-428
• /
• 2016

The last stage blades of a low pressure (LP) turbine get frequently fractured because of stress corrosion cracking. This is because they operate in a severe corrosive environment that is caused by the impurities dissolved in condensed steam and high stress due to high speed rotation. To improve the reliability of the blades under severe conditions, 12% Cr martensitic stainless steel, having excellent corrosion resistance and higher strength, is widely used as the blade material. This paper shows the result of root cause analysis on a blade which got fractured suddenly during normal operation. Testing of mechanical properties and microstructure examination were performed on the fractured blade and on a blade in sound condition. The results of testing of mechanical properties of the fractured blade showed that the hardness were higher but impact energy were lower, and were not meeting the criteria as per the material certificate specification. This result showed that the fractured blade became embrittled. The branch-type crack was found to have propagated through the grain boundary and components of chloride and sulfur were detected on the fractured surface. Based on these results, the root cause of fracture was confirmed to be stress corrosion cracking.

• Korean Journal of Applied Biomechanics
• /
• v.12 no.2
• /
• pp.381-392
• /
• 2002

This study attempted to indentify changeability of the factorial structure of kinematic analysis in bowling. Subjects of group composed of three groups : Higher bowers who are national representative bowers with 200 average point and one pro-bowler. Middle bowlers who are three common persons with 170 average points. Lower bowler who are three common persons with 150 average points. Motion analysis on throw motion in three groups respectively has been made through three-dimension cinematography using DLT method. Two high-speed video camera at operating 180 and 60 frame per secondary. T-test factorial structure analysis has been used to define variable relations. It was concluded that : 1. The difference of x1, x2, x4, x8, x9, x11, x12, x13 where significant between two group. 2. The difference of number of spin and angle of the back-hand where statistically significant between two group(p<.001, p<.05) 3. The correlation over r=.5 between the kinematic data x1, x2, x3, x9, x10, x11. In the rotation loading matrix Factor 1 was x1, x2, x9, x10 and Factor 2 relates to x3, x11. 4. In order to obtain the factor score as follow as ; Factor 1 = (0.248)X1 + (0.265)X2 + (-0.074)X3 + (0.259)X9 + (0.259)X10 + (-0.025)X11 Factor 2=(-0.016)X1 + (-0.055)X2 + (0.84)X3 + (-0.013)X9 + (-0.007)X10 + (0.553)X11.