• Structural Engineering and Mechanics
• /
• v.61 no.2
• /
• pp.221-230
• /
• 2017

In this paper, we investigated the propagation of thermoelastic surface waves in fibre-reinforced anisotropic general viscoelastic media of higher order of nth order including time rate of strain under the influence of rotation. The general surface wave speed is derived to study the effectsof rotation andthermal onsurface waves. Particular cases for Stoneley, Love and Rayleighwaves are discussed.The results obtained in this investigation are more general in the sense that some earlier published results are obtained from our result as special cases. Our results for viscoelastic of order zero are well agreed to fibre-reinforced materials. Comparison was made with the results obtained in the presence and absence of rotation and parameters for fibre-reinforced of the material medium. It is also observed that, surface waves cannot propagate in a fast rotating medium.Numerical results for particular materials are given and illustrated graphically. The results indicate that the effect of rotation on fibre-reinforced anisotropic general viscoelastic media are very pronounced.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.5
• /
• pp.628-634
• /
• 2003

We present numerical and experimental results of periodic flows inside a rectangular container under a background rotation. The periodic flows are generated by changing the speed of rotation periodically so that a time-periodic body forces produce the unsteady flows. In numerical computation, a parallel-computation technique with MPI is implemented. Flow visualization and PIV measurement are also performed to obtain velocity fields at the free surface. Through a series of numerical and experimental works, we aim to clarify, if any, the fundamental reasons \ulcornerf discrepancy between the two-dimensional computation and the experimental measurement, which was detected in the previous study for the same flow model. Specifically, we check if the various assumptions prerequisite for the validity of the classical Ekman pumping law are satisfied for periodic flows under a background rotation.

• Transactions of Materials Processing
• /
• v.12 no.8
• /
• pp.730-737
• /
• 2003

Extensive studies have been conducted for reducing the residual stresses and birefringence in injection-molded optical disk substrate Flow-induced and thermally-induced stresses and birefringence have been found as two main sources during injection molding process. However, high speed rotation also induces extra stresses and birefringence in real operation of disk drives. In the present paper rotation-induced in-plane birefringence has been measured and presented for CD and DVD substrates at different radial position. About 10 - 15 nm of extra retardation in one pass has been measured up to 4,800 rpm. The distribution of extra rotation-induced birefringence will be valuable data for designing an optimal optical disk substrate. Finally, experimental results were compared with the extra stresses calculated from simple formulation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.3
• /
• pp.273-286
• /
• 2017

We develop an inspection method for bearing faults with a rapid change in the rotation speed and present indexes for the pass/fail inspection. At the end of line, impulse noises generated by the operation of machines and conveyors may distort the inspection results. In this paper, we present robust inspection indexes for bearing faults under impulse noises, by taking into account fault signals having pulse train. Using logistic regression, we optimize the pass/fail criterion for each index and evaluate the performance of the inspection indexes based on the total error rate.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.676-681
• /
• 2003

In this paper, we investigated the disc warping in high-speed slim-type optical disc drive. Recently, the information storage devices are increasing track density and higher rotation speed to enhance their recording capacity and their data transfer rate. Generally, ODD used in the Lap-top Computer has small inner space. So, the flow instability of inner space is rapidly increased as its higher rotation speed. An extreme case, the flow instability causes the malfunction of readout at pick-up of drives. The experiments and numerical analysis were carried out for several cases, the result shows the influence of airflow to the disc warping.

• 유체기계공업학회:학술대회논문집
• /
• 1999.12a
• /
• pp.33-40
• /
• 1999

Upgrade development of a high pressure ratio centrifugal compressor in marine engine turbochargers is presented. A new matched operating point at increased speed of rotation was determined through system cycle analysis using the exisitng test data of turbine performance. Under some severe restrictions for geometric parameters, the state-of-the-art methods of both aerodynamic design and CFD analysis were applied, in which only an impeller, a vaned diffuser and some part of casing wall were modified. Prototype hardware was fabricated and assembled for system performance tests. Excellent performance in pressure ratio and efficiency was obtained over whole speed region. Reduced surge and choke margin was, however, observed at design speed of rotation.

• Food Science and Preservation
• /
• v.18 no.5
• /
• pp.627-635
• /
• 2011

This study was conducted to assess the effects of the removal of pesticide residues and microorganisms from yuja (Citrus junos Sieb ex Tanaka) using a surface-washing system, under the following washing conditions: 0.11, 0.42, and 0.73 m/s spray rotation speeds; 0.6, 0.9, and 1.2 MPa water pressure and 0.046, 0.092, and 0.138 m/s conveying speeds. Tap-water treatment was used as the control. The washing efficiency when using squid ink was highly correlated with the conveying speed and the spray rotation speed. In addition, the highest washing efficiency was achieved when the water pressure was 0.9 MPa. The microorganisms were reduced to 0.40 log CFU/g for the tap-water treatment, and all the treatments, except those at the conveying speed of 0.138 m/s and the spray rotation speed of 0.11 rpm (6.07 log CFU/g), produced higher removal efficiencies compared with the tap-water treatment. Reductions of 2.20 and 2.05 log CFU/g were achieved at the spray rotation speeds of 0.42 and 0.73, respectively. The largest reductions were observed when the conveying speed was 0.046 m/s. Higher pesticide residue removal efficiency values were obtained at slower conveying speeds and higher spray rotation speeds. Higher than 50% removal efficiency was achieved when the spray rotation speed was 0.046 m/s for spirodichlofen, deltamethrin, benomyl, thiophanate-methyl, and acequinocyl. Especially, the removal efficiency for benomyl and thiophanate-methyl was more than 90%. It can thus be concluded that the pesticide residues in yuja can be effectively reduced by washing the latter with a less-than-0.092-m/s conveying speed and a higher-than-0.42-m/s spray rotation speed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.1
• /
• pp.30-41
• /
• 2006

This paper shows mechanical Properties and behaviors of macrostructures for specimens welded by F.S.W according to welding conditions and tool dimensions with $6.35mm_t$ aluminum 7075-T651 alloy plate. It apparently results in defect-free weld zone in case transition speed was changed to 15mm/min 61mm/min and 124mm/min under conditions of tool rotation speed such as 800rpm. 1250rpm and 1600rpm respectively with tool's Pin diameter 40mm and 60mm. The optimum mechanical property, ultimate stress,${\sigma}_Y=470Mpa$ is obtained at the condition of 124mm/min of travel speed with 800rpm of tool rotation speed using full screw type pin. shoulder dia. $20{\phi}mm$ pin dia. $6{\phi}mm$ and pin length 6mm. The full-screw type and the half-screw type pin shows the similar behaviors of weldability. It is found that the size of nugget is depended on tool transition speed and tool dimension by macrostructures of the cross section of weld zone.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.348-358
• /
• 2005

This paper showed mechanical properties and behaviors of macrostructures for specimens welded by F.S.W according to welding conditions and tool with 6.35$mm_t$ aluminum 7075-T651alloy plate. It resulted in defect-free weld zone in case tool rotation speed was 800rpm, 1250rpm and 1600rpm respectively that transition speed was changed to 15mm/min, 61mm/min and 124mm/min with tool's pin diameter 4${\Phi}$mm and 6${\Phi}$mm. The optimum mechanical property, ultimate stress,${\sigma}_Y$=470Mpa was obtained at the condition of 124mm/min of travel speed with 800rpm of tool rotation speed using full screw type pin, shoulder dia. 20${\Phi}$mm, pin dia.6${\Phi}$mm and pin length 6mm. The full-screw type and the half-screw type pin showed the similar behaviors of weldability. It is found that the size of nugget was depended on tool transition speed and tool dimension by macrostructures of the cross section of weld zone.

• Korean Journal of Applied Biomechanics
• /
• v.18 no.1
• /
• pp.53-62
• /
• 2008

The purpose of this research was to analyze the kinematics of the 205B movement in platform diving. For the experiment, 2 athlete from the national diving team were chosen as the subject and two S -VHS video cameras were used. For this diving players preparing for the olympics participated. It was shown that the mean total took $1.112{\pm}0.12s$. In order to perform better, the divers time must be increased, at take off and rotation must be done high up and the horizontal distance must be shorted to main entrance of the water. To enter the water safely, the jump has to be high, the horizontal speed slow and the vertical speed as fast as possible. At E1 the lower limbs change in speed should decrease and after the rotation begins at E2. At take off, the jump is more important than the rotation for the performance of the dive. At take off, the trunk angular velocity was high, and this was needed to jump high for moment of inertia for rotation because for efficient jumping the upper body has to spread out and increase the height of the center of mass.