• Korean Journal of Materials Research
• /
• v.2 no.1
• /
• pp.52-57
• /
• 1992

The macro defects of $LiNbO_3$ crystals grown by the Czochralski method were strongly influenced by the single crystal growth parameters such as growth rate, thermal gradient and crystal rotation rate. The optimum growth conditions of a $LiNbO_3$ single crystal with 1" in diameter were $70~100^{circ}C/cm$ temperature gradient, 5~10 mm/hr growth rate and 40 rpm crystal rotation rate. In these conditions, we could grow crystals which had no cellular structure with easy diameter control, and any crack was not formed after the crystal was cooled.oled.

• Korean Journal of Crystallography
• /
• v.4 no.1
• /
• pp.11-17
• /
• 1993

Corundum single crystals were grown by the Czochralski technique. Relationships between crystal quality and crystal growth factors such as pulling rate, rotation rate and temperature of the melt were investigated. Optimum pulling and rotation rate for high quality corundum single crystal growth were 4.0mm/hr, 30rpm respectively. Pore was a main defect in corundum crystal and also discussed how to remove this defect by melt temperature control. Growth direction of as grown crystals was identified with(0001). And this direction had largest growth rate. Room temperature absorption spectra were measured and discussed for Cr3+ion doped and non-doped corundum crystals.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.3
• /
• pp.115-121
• /
• 2019

Response surface methodology (RSM) is used to investigate the complex coupling effects of different operating parameters on silicon growth rate in planetary CVD reactor. Based on the computational fluid dynamics (CFD) model, an accurate RSM model is obtained to predict the growth rate with different parameters, including temperature, pressure, rotation speed of the wafer, and the mole fraction of dichlorosilane (DCS). Analysis of variance is used to estimate the contributions of process parameters and their interactions. Among the four operating parameters that have been studied, the influences of susceptor temperature and the operating pressure were the most significant factors that affect silicon growth rate, followed by the mole fraction of DCS. The influence of wafer rotation is the least. The validation tests show that the results of silicon deposition rate obtained from the regression model are in good agreement with those from CFD model and the maximum deviations is 2.15%.

• Journal of the Optical Society of Korea
• /
• v.17 no.5
• /
• pp.357-361
• /
• 2013

A regenerative Er-doped fiber amplifier system for a high-repetition-rate optical pulse train is investigated for the first time. A signal pulse train with a wavelength tuning range of 18 nm is produced by a passive mode-locked fiber laser based on a nonlinear polarization rotation technique. In order to realize the amplification, an optical delay-line is used to achieve time match between the pulses' interval and the period of pulse running through the regenerative amplifier. The 16 dB gain is obtained for an input pulse train with a launching power of -30.4 dBm, a center wavelength of 1563.4 nm and a repetition rate of 15.3 MHz. The output properties of signal pulses with different center wavelengths are also discussed. The pulse amplification is found to be different from the regenerative amplification system for CW signals.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.6
• /
• pp.547-552
• /
• 1999

Langasite$(La_{3}Ga_{5}SiO_{14})$ single crystal was successfully grown by Floating Zone (FZ) method and characterized. The growth rate was 1.5 mm/h and the rotation speed was 15 rpm for an upper rotation and 13 rpm for a lower rotation. The grown crystal was 12 mm in length and 6 mm in diameter. The grown crystal was dark orange color and it was grown along [001] direction. The composition of grown crystal and the structure were analyzed using XRD and WDS. The electrical properties of grown crystal at various frequencies and temperatures were discussed.

• Proceedings of the Korea Multimedia Society Conference
• /
• 2000.04a
• /
• pp.449-452
• /
• 2000

This paper proposes a new, adaptive Dead Reckoning model, called Dynamic Dead Reckoning , for Distributed Interactive Simulation and humanoid avatar systems. The proposed model can overcome the weak points of traditional Dead Reckoning caused by a fixed threshold and strong dependency on rotation event. This paper introduces new criteria for update message filtering , named as Update lifetime. The Dynamic Dead Reckoning keeps the balance between extrapolation fidelity and filtering performance by two component models, Variable Threshold Mechanism and Rotation Event model. The experimental results show that the proposed model can lower the increment rate of update traffic to the increase of rotation frequency without any significant loss of accuracy.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.627-632
• /
• 2000

Developing turbulent flows in a rotating 90 degree bend with square cross-section were measured by a hot-wire anemometer. The six orientation hot-wire technique was applied to measured the distributions of 3 mean velocities and 6 Reynolds stress components. Effects of Coriolis and centrifugal forces caused by the curvature and rotation of bend on the mean motion and turbulence structures were experimentally investigated Productive addition of Coriolis and centrifugal forces to the outward radial direction in the entrance region of bend increases the secondary flow intensity according to the rotational speeds. However, after 45 degree of bend, centrifugal force due to the rotation of bend may promote the break down of counter rotating vortex pair into multi-cellular pattern, thereby decreasing the production rate of turbulence energy and Reynolds stresses.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1682-1687
• /
• 2003

Die polishing technology is very critical to determine quality and performance of the final products. Generally, the rotation-type tool is used most widely in the polishing process. However it is difficult to make the mirror surface, because the method using the rotation-type tool causes a lot of tiny scratch on the polished surface. This paper proposes a new method using the oscillation-type tool that reduces the scratch and improves the surface roughness. As result. the mirror surface was able to obtain by using the oscillation-type tool. AE is known to be closely related to material removal rate(MRR). As the surface is rougher, MRR gets larger and AE increase. The surface roughness can be indirectly estimated using the AE signal measured during automatic die polishing process. In this study. an AE sensor based monitoring system was developed to investigate the relation the level of AE RMS with the surface roughness during polishing process.

• Korean Journal of Optics and Photonics
• /
• v.5 no.1
• /
• pp.131-137
• /
• 1994

We demonstrate a novel mode locked fiber laser gyroscope that utilizes a rare-earth doped fiber. The output of the gyroscope is a series of short optical pulses. Without rotation, the optical pulses are equally spaced in the time domain. With rotation, the intervals of the optical pulses changes. By measuring the separation of the optical pulses in time domain, the rotation rate could be obtained. We also discuss the polarization effect that can cause signal errors.errors.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.2
• /
• pp.90-95
• /
• 2011

This paper presents the study on the contact stress analysis of a pair of mating helical gears for turbo blower during rotation. Turbo blowers need high speed rotation of impeller in structure and high rate gear ratio. The use of helical gear indicated that noise was an important problem when the application involves high speeds and large power transmission. An example is presented to investigate the variation of contact stress on a pair of mating gears with contact positions. The variation of contact stress during rotation is compared with the contact stress at the lowest point of single tooth contact(LPSTC) and AGMA Equation for contact stress. In this study, the gear design considering the contact stress on a pair of mating gear is more severe than that of AGMA standard.