• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.6
• /
• pp.883-888
• /
• 2010

This study have goal with conceptual design for Offshore Structures of high pressure control valve for localization. Ball valve for development accomplished with flow analysis based on provision of ANSI B16.34, ANSI B16.10, ANSI B16.25 In order to localize the Offshore Structures high pressure control valve. Numerical simulation using CFD (Computational Fluid Dynamic) in order to predict a mass flow rate and a flow coefficient form flow dynamic point of view. The working fluid assumed the glycerin (C3H8O3). The valve inlet and outlet setup a pressure boundary condition. The outlet pressure was fixed by atmospheric pressure and calculated until increasing 1bar to 10bar. CFD analysis used STAR-CCM+ which is commercial code and Governing equations were calculated by moving mesh which is rotated 90 degrees when ball valve operated opening and closing in 1 degree interval. The result shows change of mass flow rate according to opening and closing angle of valve, Flow decrease observed open valve that equal percentage flow paten which is general inclination of ball valve. Relation with flow and flow coefficient can not be proportional according to inlet pressure when compare with mass flow rate. Because flow coefficient have influence in flow and pressure difference. Namely, flow can be change even if it has same Cv value. The structural analysis used ANSYS which is a commercial code. Stress analysis result of internal pressure in valve showed lower than yield strength. This is expect to need more detail design and verification for stem and seat structure.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1195-1200
• /
• 2008

This study have goal with conceptual design for Offshore Structures of high pressure control valve for localization. Ball valve for development accomplished with flow analysis based on provision of ANSI B16.34, ANSI B16.10, ANSI B16.25 In order to localize the Offshore Structures high pressure control valve. Numerical simulation using CFD(Computational Fluid Dynamic) in order to predict a mass flow rate and a flow coefficient form flow dynamic point of view. The working fluid assumed the glycerin($C_3H_8O_3$). The valve inlet and outlet setup a pressure boundary condition. The outlet pressure was fixed by atmospheric pressure and calculated until increasing 1bar to 10bar. CFD analysis used STAR-CCM+ which is commercial code and Governing equations were calculated by moving mesh which is rotated 90 degrees when ball valve operated opening and closing in 1 degree interval. The result shows change of mass flow rate according to opening and closing angle of valve. Flow decrease observed open valve that equal percentage flow paten which is general inclination of ball valve. Relation with flow and flow coefficient can not be proportional according to inlet pressure when compare with mass flow rate. Because flow coefficient have influence in flow and pressure difference. Namely, flow can be change even if it has same Cv value. The structural analysis used ANSYS which is a commercial code. Stress analysis result of internal pressure in valve showed lower than yield strength. This is expect to need more detail design and verification for stem and seat structure.

• Computational Structural Engineering
• /
• v.10 no.2
• /
• pp.255-263
• /
• 1997

The optimum design of most structural systems used in practice requires considering design variables as discrete quantities. The present paper shows that the linear approximation method is very effective as a tool for the discrete optimum designs of unsymmetric composite laminates. The formulated design problem is subjected to a multiple in-plane loading condition due to shear and axial forces, bending and twisting moments, which is controlled by maximum strain criterion for each of the plys of a composite laminate. As an initial approach, the process of continuous variable optimization by FDM is required only once in operating discrete optimization. The nonlinear discrete optimization problem that has the discrete and continuous variables is transformed into the mixed integer programming problem by SLDP. In numerical examples, the discrete optimum solutions for the unsymmetric composite laminates consisted of six plys according to rotated stacking sequence were found, and then compared the results with the nonlinear branch and bound method to verify the efficiency of present method.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.4
• /
• pp.223-230
• /
• 2014

In this paper, the wind-induced response characteristics of freeform shaped tall building is studied by using FSI analysis. The analytical models are twist shaped ones at representing type of atypical tall building, and this study focused on the relationship between twist angle and wind acceleration. Firstly, 1-way FSI analysis is performed, so maximum lateral displacement of the analytical model for 100 years return period wind speed is calculated, then the elastic modulus of a structure that satisfies the constraints condition is evaluated. And 2-way FSI analysis is carried out. so acceleration of the analytical model for the evaluated modulus of elasticity and arbitrary density is predicted through time history analysis. The basic model is a set of a square shape, height is 400m, slenderness ratio is 8, and twist model is rotated at square model from 0 to 90 degrees at intervals of 15 degrees and from 90 to 360 degrees at intervals of 90 degrees. According to the result of predicting wind acceleration by the shape of each model, the wind vibration effect of square shape model is confirmed to be sensitive more than a twist shape ones.

• Journal of Energy Engineering
• /
• v.25 no.2
• /
• pp.21-28
• /
• 2016

This research was conducted for the optimal design of large commercial gas oven system. Equivalent ratio was determined through a numerical analysis and experiments on the combustion condition of the combustor. After reviewing the supply capacity of burner(20,000 kcal) and control method of convection fan, two types of heat exchangers designed. In order to maintain a uniform temperature inside the oven is required convection fan braking system. The center temperature in the oven rises more rapidly when the convectional fan is rotated in the counterclockwise direction than the counter-clockwise direction. And The efficiency of the system by installing a large heat transfer area was higher.

• Journal of Animal Science and Technology
• /
• v.65 no.3
• /
• pp.638-651
• /
• 2023

The objective of this study was to quantitatively estimate the level of grazing area damage in outdoor free-range pig production using a Unmanned Aerial Vehicles (UAV) with an RGB image sensor. Ten corn field images were captured by a UAV over approximately two weeks, during which gestating sows were allowed to graze freely on the corn field measuring 100 × 50 m². The images were corrected to a bird's-eye view, and then divided into 32 segments and sequentially inputted into the YOLOv4 detector to detect the corn images according to their condition. The 43 raw training images selected randomly out of 320 segmented images were flipped to create 86 images, and then these images were further augmented by rotating them in 5-degree increments to create a total of 6,192 images. The increased 6,192 images are further augmented by applying three random color transformations to each image, resulting in 24,768 datasets. The occupancy rate of corn in the field was estimated efficiently using You Only Look Once (YOLO). As of the first day of observation (day 2), it was evident that almost all the corn had disappeared by the ninth day. When grazing 20 sows in a 50 × 100 m² cornfield (250 m²/sow), it appears that the animals should be rotated to other grazing areas to protect the cover crop after at least five days. In agricultural technology, most of the research using machine and deep learning is related to the detection of fruits and pests, and research on other application fields is needed. In addition, large-scale image data collected by experts in the field are required as training data to apply deep learning. If the data required for deep learning is insufficient, a large number of data augmentation is required.

• Korean Journal of Applied Biomechanics
• /
• v.26 no.2
• /
• pp.175-181
• /
• 2016

Objective: The aim of this study was to investigate age-related changes of multi-finger synergy during a constant force production task with and without an additional mechanical constraint. Method: Fourteen elderly subjects (age: $78.50{\pm}4.63yrs$, height: $157.29{\pm}8.97cm$, weight: $65.13{\pm}6.93kg$) and 14 young subjects (age: $21.13{\pm}1.35yrs$, height: $171.57{\pm}8.43cm$, weight: $70.29{\pm}16.77kg$) participated in this study. The subjects were asked to place their index and middle fingers on two force transducers fixed on a small non-moving teeterboard and produce 10 N by pressing the sensors while watching force feedback on a computer screen under the no additional constraint condition (NAC). The subjects also performed the same task with an additional mechanical constraint (AC) where the subjects were asked to balance a teeterboard that could be rotated by finger forces. An uncontrolled manifold approach was used to calculate within-trial and between-trial multi-finger synergy indices, variance in uncontrolled subspace ($V_{UCM}$), and variance in subspace orthogonal to UCM subspace ($V_{ORT}$). Two-way repeated measured ANOVA was performed with the within-factor of task condition (with and without an additional constraint) and the between factor of groups (elderly and young). Results: The elderly group showed significantly increased within-trial $V_{ORT}$ in AC compared with NAC (p < .05) while the young group showed no significant difference between AC and NAC. There was no significant group difference for within-trial $V_{UCM}$. Between-trial $V_{ORT}$ remained unchanged between groups and conditions. However, between-trial $V_{UCM}$ for the elderly group significantly decreased in AC as compared to NAC, along with no significant difference for the young group. For multi-finger synergy, there was no significant group difference of within-trial synergy. However, between-trial synergy for the elderly group significantly decreased in AC as compared to NAC (p < .05). Conclusion: Our results indicate that aging decreased consistency (i.e., ability to perform the task on a moment-to-moment basis) with an additional mechanical constraint. In addition, aging was associated with decreased multi-finger synergy on a trial-to-trial basis.

• Fire Science and Engineering
• /
• v.24 no.5
• /
• pp.32-38
• /
• 2010

Multi-dimensional fire dynamics were studied numerically with the change in ventilation conditions in a full-scale ISO 9705 room. Fire Dynamic Simulator (FDS) was used for the identical conditions conducted in previous experiments. Flow rate and doorway width were changed to create over-ventilated fire (OVF) and under-ventilated fire (UVF). From the numerical simulation, it was found that the internal flow pattern rotated in the opposite direction for the UVF relative to the OVF so that a portion of products recirculated to the inside of compartment. Significant change in flow pattern with ventilation conditions may affect changes in the complex process of CO and soot formation inside the compartment due to increase in the residence time of high-temperature products. The fire behavior in the UVF created complex 3D characteristics of species distribution as well as thermal and flow structures. In particular, additional burning near the side wall inside the compartment significantly affected the flow pattern and CO production. The distribution of CO inside the compartment was explained with 3D $O_2$ distribution and flow patterns. It was observed that gas sampling at local positions in the upper layer were insufficient to completely characterize the internal structure of the compartment fire.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.8
• /
• pp.1795-1801
• /
• 2009

In this study, a portable flashlight which can manually generate the electricity by using sunlight was developed so that it can be used in the extreme environmental condition such as no-electricity condition. Battery is charged by using solar battery during the day, but when sunlight is not avalible during the night or rainy day, a handle is rotated to generate the electricity in order to charge the battery manually. To improve the brightness of the light, light is concentrated by using the optical lens. Low electric consumption circuit is used for the longer operating time by suppress electrical consumption while lamp is discharged. A circuit is designed and used for steady electrical curris dand voltage to insure steady battery charging. Super-discharge circuit and protection circuit are used for the super discharge of battery when it is not used for a long time. Also the constant charge is possible by using houseware adapter. As a result, a portable flashlight is designed to charge with sunlight during day, and with houseware adapter during night. A portable flashlight is also designed to irradiate longer distances by improvement of the brightness of the light using the optical lens. Thus, it forms white natural ray of light making possible for night reading.

• Journal of Korean society of Dental Hygiene
• /
• v.10 no.3
• /
• pp.523-530
• /
• 2010

Objectives : In order to provide basic data necessary for developing oral health education plane for school continued oral health education by understanding knowledge and activities of oral health. Methods : This study was performed against 324 students at 5th grade of 2 elementary schools in Iksan-si, Jellabuk-do selected through convenience sampling, who were in mixed dentition period that might experience dental caries of permanent tooth. Results : As results, For the knowledge level on oral health by questions, it was found that the case that the elementary school students had correct knowledge on oral health was 'chocolates, snacks, and candies were foods that might often cause dental caries' and 95.8% of the students recognized it well. It was found that for 'must do toothbrushing before going to bed', 'during toothbrushing, I clean my tongue', and 'Proper time necessary for toothbrushing is about 3 minutes', 89.3%, 93.2%, and 89.3% of the students knew the, respectively. When oral health knowledge level by groups was divided into 3 groups and observed, they were classified into Low (0-4 points), Mid (5-7 points), and High (8-10 points). It was found that the knowledge level of each group was High 64.1%, Mid 33.9%, and Low 2.0% and it was identified that the high group took the largest ratio. It was suggested also for oral health knowledge level depending on their father's academic background that there was a statistically significant difference in the group higher than university graduate(p<.05). It was found for oral health knowledge level depending on parents' dental condition that an answer that both parents were good was high and there was a statistically significant difference. But post-analysis resulted that there was no apparent difference among groups. It was found that the ratio of respondents who answered for toothbrushing method 'toothbrush should be moved and rotated downward for the upper teeth and upward for the lower teeth to clean the teeth and gum' were 33.2% of male students and 29.4% of female students and showed statistically significant difference (p<0.05). It was found also that the ratio of respondents who answered to use a toothbrush for about 3 months' were 29.4% of male students and 25.5% of female students and showed statistically significant difference (p<0.05). Conclusions : Oral health program through the elementary school students and their parents for the development of proper oral health care education programs continue to be made should be considered.