• Tribology and Lubricants
• /
• v.31 no.6
• /
• pp.281-286
• /
• 2015

Automotive transmission systems are assembled with a large number of gears and shafts, and rolling bearings are used to ensure their smooth operation. Gear oil in the gear box contains solid particles such as wear debris from contacting gears and metallic chips. This particle-enriched lubricating oil can cause premature failure of the rolling bearings. Research aimed at improving the service life of these rolling bearings has been confined mainly to design and lubrication of the inner/outer rings and the rolling elements. In this paper, we redesigned the shape of the cage pocket of a deep groove ball bearing to reduce the premature failure due to particle contamination. Test bearings are assembled with this new cage design containing a hole punched in the cage pocket. Endurance tests are carried out using the contaminated lubricating oil with miracle grid as hard particle. The duration and damaged bearing component shapes are compared for two different cages. The B₁₀ life of bearing with new cage is increased by about 66% compared to the conventional cage. This is because the hard particles can be easily discharged through the pocket hole without staying for a long time in the lubrication regions. This greatly decreases abrasive wear and dents on the highly stressed ball bearing surfaces. Therefore, the cage design of this study, containing a pocket hole, can significantly delay the premature failure of rolling bearings and improve the endurance life.

• Tribology and Lubricants
• /
• v.22 no.5
• /
• pp.269-275
• /
• 2006

Rolling bearings are classified one of the most important machine elements. The various function of bearings are greatly influenced by grease, and higher performance of rolling bearing greases is required to improve bearing lubrication. Three urea/ether oil greases with different composition were synthesized to compare the performance of these greases. The typical grease physical properties were investigated, and life test of these greases was conducted by FE-9 grease life tester. The grease with higher content of the thickener showed higher performance. After these preliminary test, twelve greases were synthesized and evaluated the performance of dropping point and OIT value. And optimized conditions for grease synthesis were selected by SSRED (Six Sigma Robust Engineering Design) using dropping point and OIT value respectively. The optimized grease using OIT value showed longer grease life than that using dropping point. Two greases were synthesized following the optimum synthesis conditions by means of OIT value. Then grease life and other properties of these greases were investigated. These two greasaes showed longer grease life than typical urea/ether oil grease.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.129-138
• /
• 2003

Rolling bearings are classified one of the most important machine elements. The various function of bearings are greatly influenced by grease, and higher performance of rolling bearing greases is required in improve bearing lubrication. Three urea/ether oil greases with identical composition were synthesized to compare the performance of these greases according to the thickener content of grease. The typical grease physical properties were investigated. And life test of these greases was conducted by FE-9 grease life tester. The characteristics of the greases before and after life test were investigated using FT-IR, microscope, OIT and TAN meter. Large differences in the grease performance depending on the content of the thickener were observed. The grease with higher content of the hickener showed higher performance such as long life time and low TAN value. After preliminary test, twelve greases were synthesized and evaluated the performance of dropping point and OIT, then optimized two greases were selected by SSRED (Six Sigma Robust Engineering Design) using dropping point and OIT data. Characteristics of the optimized two greases were on the same level with estimated value. The optimized grease by means of OIT value showed longer grease life in comparison with optimized grease by dropping point. However two greases showed higher performance than typical urea/ether oil.

• Tribology and Lubricants
• /
• v.15 no.2
• /
• pp.150-155
• /
• 1999

The rolling fatigue lives (RFL) of five kinds of silicon nitride balls were investigated. Four kinds of Si$_3$N$_4$balls were fabricated using different raw materials, sintering aids and sintering conditions. Commercially available Si$_3$N$_4$ball was also studied for comparison. All the balls were finished up to the dimensional accuracy of Grade 10 defined in KS B 2001 (Steel Balls fer Ball Bearings) with a size of 9.525 mm. RFL tests were then conducted under the initial theoretical maximum contact stress 6.38 GPa and the spindle speed 10,000 rpm. Gear oil was provided by oiled race as lubricant. The results of RFL test indicated the prerequisitic conditions for the long rolling life of Si$_3$N$_4$ball : (1) the high density, (2) microstructures consisted of small uniformly distributed grains, (3) little glassy phase in grainboundary, and (4) little crystalline phase and secondary phase that induces residual thermal stress due to the differences of thermal expansion coefficient with Si$_3$N$_4$phase.

• Tribology and Lubricants
• /
• v.13 no.2
• /
• pp.39-45
• /
• 1997

The shot peening treatment were conducted for improving the strength of rolling contact fatigue of machine element like a gear. This paper was undertaken to analyze the influence of shot peening treatment for inner race of ball bearing on the rolling contact fatigue. Shot peening treatment were applied to the full hardened and the carbonitrided bearing. And the rolling contact fatigue life test and X-ray diffraction test were carried out. The results of this study showed that the fatigue life of ball bearing in the clean and the contaminated oil could be improved by shot peening treatment. This effect was found to be more pronounced to the full hardened bearing. These facts might be due to the generation of compressive residual stress and the strain hardening of surface layer by shot peening treatment. The failure of the shot peened bearing were presumed to initiate at surface.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.7
• /
• pp.1363-1372
• /
• 1992

The effects on lubricity and the anti-seizure property of lubricant according to base oils and extreme pressure additives of sulfur type and phosphorous type in cold rolling were evaluated by a laboratory scale rolling mill, where the contact conditions between work roll and strip are very close to actual cold rolling mill. The important results were obtained as follows : (1) synthetic oil has better effect on lubricity than tallow, (2) lubricant with extreme pressure additives of sulfur type of phosphorous type has better effect than base oil noly, (3) the more amount of extreme pressure additives is, the better effect on lubricity is, (4) sulfur type has better effect on lubricity than phosphorous type and (6) phosphorous type has better effect on anti-seizure property than sulfur type.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2910-2916
• /
• 2011

Environmental conservation is becoming the major conversation topic in the 21st century, the era of environment. In the Law for the Preservation of Water Quality, article 53 states "A business unit which is doing business causing pollution caused by non-point pollutant or builds waste water discharge facilities, should report the installation of the non-point pollutant and install the required pollution control facilities". Environmental pollution caused by oil leaks during operation or maintenance has been found in the railway sector. Especially, rolling stock depot is most likely to be affected by environmental pollution. Therefore, in this paper We have investigated non-point pollutant in the rolling stock depot area and have studied adequate disposal method to minimize the effect of the non-point pollutant, hoping to supply the preliminary data for building an environment-friendly rolling stock depot.

• Journal of the Korean Applied Science and Technology
• /
• v.27 no.4
• /
• pp.522-530
• /
• 2010

We developed functional synthetic lubricant for internal combustion engine oil, which would improve engine oil performance for internal combustion engine and extend engine life. We made base oil by synthesizing nonanoic acid, 1.1.1-trimethylol propane (which has good bio-degradability) and pentaerythrytol ester. We synthesized catalyst using p-toluene sulfonic acid 0.15 wt% and coloring-prevention agent hypo-phosphorus acid 0.18 wt% at 180-$190^{\circ}C$. Reaction temperature was increased at the rate of $10^{\circ}C$ for every 1 hour. When acid value reached below 3, reaction was completed. After cooling and deoxidization, we washed it by distilled water two times. After dehydration and filtering, we obtained trimethylol propane tripelargonate (TMTP) and pentaerythrytol tetrapelargonate (PETP) at yields of 96 % and 98 % respectively.

• Environmental and Resource Economics Review
• /
• v.22 no.2
• /
• pp.251-279
• /
• 2013

Prices of oil products such as gasoline and diesel are deregulated since 1997 while electricity price is still controlled by government. This difference may explain recent discrepancy in the patterns of demand for oil products and electricity - constant increase in electricity consumption and stagnant demand for oil. To verify it empirically, we estimate price and income (production) elasticity of demand across time by using a rolling regression with 10 year-window based on monthly data for 1981-2011. Estimation results show that the sensitivity to price in demand for gasoline and diesel has increased since mid-90s while the elasticity of demand for electricity has become smaller. Second, income (production) elasticities of demand have shown no significant changes for both oil products and electricity. Third, cross-price elasticity was found meaningful only for gasoline before mid 1990s and for diesel after then.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.424-426
• /
• 2008

A parametric study was carried out to find the fuel lubrication performance of high speed small rolling element bearings. Both MIL-PRF-7808 turbine oil and JP-8 aircraft fuel were used as the lubricant to compare the operational characteristics. 17 mm inner diameter deep groove ball bearing and 20 mm cylindrical roller bearing were used. A high speed bearing test rig was developed and the testing was done with varying applied load, cooling air temperature, lubricant flow rate, and speed. Fuel caused more cage wear than oil for ball bearing with increasing axial load and rotational speed. The bearing temperature using fuel was lower than that using oil, and this seems to be the result of the high cooling capacity of fuel. According to various tests, the fuel lubrication is applicable for the lubrication on the main shaft bearings of expendable small gas turbines.