• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 추계학술대회 논문집
• /
• pp.721-722
• /
• 2008

• 한국정밀공학회지
• /
• 제32권12호
• /
• pp.1011-1016
• /
• 2015

In a roll-to-roll continuous system, winding is one of the most important processes since it determines the quality of the final manufactured products such as flexible film and printed electronic devices. Since an adequate winding tension can reduce the incidence of the defects that are derived from the inner stress of the wound roll such as starring and telescoping, it is necessary to determine the optimal taper-tension profile. In this study, an algorithm for the setting of an optimal taper-tension profile in consideration of the residual stress in the wound roll is suggested; furthermore, the algorithm was adjusted for the determination of an optimal taper-tension profile regarding the winding process of $10{\mu}m$ polypropylene (PP) film. As a result of the algorithm-generated, optimal taper-tension profile, the residual stress and radial stress in a PP wound roll were decreased to 27.37 % and 40.05 % (mean value), respectively.

• 대한기계학회논문집A
• /
• 제31권8호
• /
• pp.847-854
• /
• 2007

The battery electrode of a mobile phone is made of layered polymer coated on aluminum foils and the hot rolling process is applied to increase the density per volume of an electrode for a high capacity battery. The flatness of batteries surfaces should be less than $2{\mu}m$. To satisfy the required flatness, the deformation of roll surface due to bending and heating of the roll should be minimized. Complicated hot oil paths of $100^{\circ}C$ inside the roll are required for heating the polymer layers. FEA was used to calculate thermal deformations and temperatures distributions of the roller. Based on FEA, a modified surface curvature called a crown roll was suggested and this gave the area of 30% improved flatness compared with a flat roll. The flat roll satisfied the flatness of $2{\mu}m$ in the length of 340 mm and the crown roll resulted in the longer length of 460 mm. Experiments to measure the temperature distribution and thermal strain were performed and compared with FEA. There were only 6% difference between two results.

• 소성∙가공
• /
• 제17권1호
• /
• pp.27-34
• /
• 2008

In order to manufacture a doubly curved sheet metal, the incremental roll forming process which adopts advantages such as the flexibility of the incremental forming process and continuous bending deformation of the roll forming process has been experimentally investigated. An experimental equipment was developed which was named as unit roll set (URS) consisting of two pairs of support rolls and an upper center roll. The upper roll equipped with the servo control unit is motor-driven and can be positioned in the vertical direction according to the user's commands. Four support rolls are idle, and they freely rotate only along the axis so as to transfer the plate more stably in the tangential direction of the rotation of the driving roll. In the process, the plate is deformed incrementally as deformation proceeds simultaneously in longitudinal and transverse directions. Through the experiments using URS, information regarding to forming schedules is found out to fabricate curved hull plates. This study demonstrates the further application of the incremental roll forming process in shipbuilding industries.

• 한국레이저가공학회지
• /
• 제15권4호
• /
• pp.12-15
• /
• 2012

On behalf of the existing semiconductor process, the electronic devices to low-cost mass production to mass print the way, the research for development of roll-to-roll printing process is actively underway. This study was performed in about the research on the manufacturing technology of the printing roll used in the printing process of electronic devices. The indirect laser imprinting technology was used to create printable roll, and after coating copper on the surface of steel and thereon after coating polymer, after removing the polymer on the surface of roll, the printable roll was made. The laser system and roll feeder system were constructed and control program was developed. We has found the optimal conditions to perform laser patterning experiments using a system developed and We can make the minimum line width of 18 ${\mu}m$.

• 수산해양기술연구
• /
• 제47권1호
• /
• pp.37-45
• /
• 2011

Reduction of ship's rolling is the most important performance requirement for improving the safety of the crew on board and preventing damage to cargo as well as improving the comfort of the ride. It is a common experience for mariners, to see that steering with a rudder generally induces rolling of the ship, though the original aim of the rudder is to keep the ship's heading to the required course. At the first stage, when a rudder is steered, usually a ship heels in an inward direction, due to the roll moment acting on the rudder. At the next stage in steering, the main heel may change to an outward. This coupling between rudder and roll motion has become an attractive problem from the point of view of roll stabilization using the rudder, because it is a natural in sight that if the rudder action is skillfully related to the change of roll as well as to the course deviation, the roll can be reduced to a certain degree. The main aim of this paper is to discuss the results of the actual full-scale sea trials carried out on steer gear No.1 and No.1 2, the individual quartermaster and to make clear their statistical properties, using the actual data which included measurement of roll angle, roll rate and the comparative tests were carried out immediately after each other, in order to minimize any statistical variation in sea conditions. It can be concluded that the steer gear No. 1 2 reduced the roll motion on average by about 21% in comparison with the No.1 and confirmed the some difference as per a ability of quarter-master's maneuver.

• 반도체디스플레이기술학회지
• /
• 제9권2호
• /
• pp.61-65
• /
• 2010

For the adaption of roll-to-roll printing method to the printed electronics, it is mandatory to increase the resolution of register errors. Therefore it is desired to derive the mathematical modeling of register error or to develop controller design. The cross direction register error was derived considering both lateral motion of moving web and transverse position of printing roll. The mathematical modeling was validated and the relationship between the lateral motion and register error was analyzed by numerical simulations in various operating conditions using multi-layer direct gravure printing machine. The results could be used for a design of the CD register in the multi-layer printing and the lateral motion caused by translation.

• 한국생산제조학회지
• /
• 제19권3호
• /
• pp.353-358
• /
• 2010

This research introduces a new and improved design for a pneumatic cylinder driven roll feeder wherein each of the principal rotating feeder parts is configured so as to have feeding accuracy and to be low manufacturing cost. The feed pitch accuracy of the proposed roll feeder was evaluated by measuring lengths of cut offs of the strip stock with a shear attached to an air press. The air press was designed, manufactured, and mounted on the same table of the proposed roll feeder such that the strip stock maintained horizontal plane until the strip stock entered into the shear. The proposed roll feeder and the air press were designed to be operated automatically by a PLC employed controller. The feed pitch accuracy of the proposed roll feeder was analyzed by setting the pitch as 10, 12.5, and 15mm. At each predetermined feed pitch, the proposed roll feeder was tested 300 times as one test set and replicated three times. The average lengths of the cut offs of the strip stock ranged from 9.98 to 10.13mm, from 12.42 to 12.57mm, and from 14.96 to 15.06mm at the predetermined 10, 12.5, and 15mm feed pitch, respectively, among the total of 900 samples of each feed pitch. Main cause of variation of the length of the cut off of the strip stock fed by the proposed roll feeder was considered to be fluctuation of the air press during recompressing period of the air compressor to pressurize the air in the air tank. The largest difference between the maximum and the minimum length of the cut off was appeared while the air compressor recompressing the air. The air compressor used for this study restricted the air delivered to the proposed roll feeder while it was still running. Thus, this air delivery restriction problem should be improved by stabilizing the air press while the proposed roll feeder is running.

• 대한기계학회논문집
• /
• 제19권2호
• /
• pp.408-417
• /
• 1995

A study on the surface roughness variation of work roll and strip at the temper rolling was performed. The results were obtained with changes according to the surface roughness of work roll and method to make the peak count on the roll in the temper rolling, and factors to affect to the work roll surface in actual rolling machine (ie. Temper mill). The results suggests that the electro-discharge textured roll has mere uniform roughness distribution than shot blasted roll and its life time is two times longer than shot blasted because it has more sine wave roughness, and it is possible to control the Rmax. In shot blasting method, Surface roughness is related to the impeller speed, But it can't control the peak count.

• 한국기계가공학회지
• /
• 제15권1호
• /
• pp.42-49
• /
• 2016

This study was analyed V-bending in order to analyze the spring-back phenomenon in the roll forming process. The material of forming sheet used in the roll forming process is high tension steel and the product name of sheet material is POSTEN 60. The most important variable is the number of roll passes (3-Pass, 4-Pass, 5-Pass, 6-Pass and 10-Pass) and other roll forming process variables were fixed. To determine the characteristics of the tension and compression, the forming sheet was analyzed by dividing the layer (Upper and Bottom) in the thickness direction from the center line. The results of FEM simulation analysis was derived to von-mises stress equivalent strain, and the spring-back value was calculated according to the final forming shape. The more number of the roll pass, von-mises stress and equivalent strain value of forming sheet were lowed. Also, spring-back values tended to decrease. The results of this study can be utilized for prediction and trend of spring-back value in the roll forming process applied to high tension steel sheet. So, development time and cost of the roll forming process is expected to be reduced.