• Tribology and Lubricants
• /
• v.30 no.3
• /
• pp.139-145
• /
• 2014

Nowadays, most micro-patterns are manufactured during flow line production. However, a conventional rotary chemical mechanical polishing (CMP) system has a limited throughput for the fabrication of large and flexible electronics. To overcome this problem, we propose a novel linear roll-CMP system for the planarization of large-area electronics. In this paper, we present a statistical analysis on the linear roll-CMP process of copper-clad laminate (CCL) to determine the impacts of process parameters on the material removal rate (MRR) and its non-uniformity (NU). In the linear roll-CMP process, process parameters such as the slurry flow rate, roll speed, table feed rate, and down force affect the MRR and NU. To determine the polishing characteristics of roll-CMP, we use Taguchi's orthogonal array L16 (44) for the experimental design and F-values obtained by the analysis of variance (ANOVA). We investigate the signal-to-noise (S/N) ratio to identify the prominent control parameters. The "higher is better" for the MRR and "lower is better" for the NU were selected for obtaining optimum CMP performance characteristics. The experimental and statistical results indicate that the down force and roll speed mainly affect the MRR and the down force and table feed rate determine the NU in the linear roll-CMP process. However, over 186.3 N of down force deteriorates the NU because of the bending of substrate. Roll speed has little relationship to the NU and the table feed rate does not impact on the MRR. This study provides information on the design parameter of roll-CMP machine and process optimization.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.05a
• /
• pp.30-35
• /
• 2004

Several roll motion reduction devices are reviewed and suggested for the application in FPSO. The firstly suggested solution is the shape of the bilge. The next is a bilge keel. The last suggestion is the ART (anti-rolling tank). Typical U-tube type ART is designed for a FPSO and examined extensively by model experiment. The model section was made of transparent acryl. Free decay test, forced oscillation test and wave test were carried out at a two-dimensional wave flume. U-tube type ART is effective only when the natural periods of ART and ship are same. Therefore, the divided U-tube type ART with split plate is suggested for the reduction of the roll motion of a FPSO over the wide range of the roll period.

• Journal of the Institute of Convergence Signal Processing
• /
• v.4 no.2
• /
• pp.53-60
• /
• 2003

For the high center of gravity vehicles the roll stiffness of their suspensions is arranged to be very high because such vehicles are in some danger of tipping over in cornering. In some cases, the effective roll stiffness is determined significantly by the compliance of the tires because of the very stiff anti-roll members incorporated in the suspension. In such cases, it is clear that the shock absorbers which may be effective in damping heave oscillations have little effect on roll oscillations. Therefore, wind gusts and roadway unevenness may cause large swaying oscillations. In this paper, to improve the stability for the high center of gravity vehicles a control scheme to augment the damping of the roll mode is proposed. As the feedback signals needed to provide damping of the roll motion, the front or rear steer angles or both are chosen because they are very related to roll motion. The scheme is effective from moderate to high speeds and stabilizes the roll mode without introducing disturbance moments from roadway unevenness as shock absorbers do. The validity on the proposed method is verified through the computer simulation.

• Journal of the Korean Society for information Management
• /
• v.24 no.2
• /
• pp.71-87
• /
• 2007

With the rapid change of the Web and E-transaction application, the search interface is providing more powerful search and visualization methods, while offering smoother integration of technology with task. Especially, visualization techniques for long menu-lists are applied in retrieval system with the goal of improving performance in user's ability to select one item from a long list. In order to review visualization techniques appropriate to the types of users and data set, this study compared the five visualization browsers such as the Tree-structured menu, the Table-of-contents menu, the Roll-over menu, the Click menu, and Fisheye menu. The result of general analyses shows that among the hierarchical methods, the experienced group prefers the Table-of-contents method menu, whereas the novice's group prefers the Tree-structure method menu. Among the linear methods, the two groups prefer the Roll-over menu. The Roll-over menu is most preferred among the five browsers by the two groups.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.859-866
• /
• 2001

During the Pre-service Inspection for Wolsong Unit 3&4 in 1997/1998 respectively, 17 Distorted Roll Transition indications(over expanded beyond tubesheet secondary face) were identified at the Unit 4 (S/G B, D). Six(6) tubes out of these tubes were plugged in 1998. However the first Periodic Inspection identified additional 110 indications in 1999 and 2000. The additionally identified 110 indication call, not reported at the Pre-service Inspection, are; 2 Not-Finally-Expanded-Tubes and 108 Distorted Roll Transition tubes. Design limit of each Steam Generator tube Plugging is 6.4%. Plugging was performed by the Steam Generator manufacturer under the warranty. When Distorted Roll Transition indications were first identified on the Unit 4 in 1998 the degree of Over-expansion was measured using an inner dial-gage to make the disposition of Nonconformance report. 2 Not-Finally-Expanded-Tubes were plugged and 10 tubes out of 108 Distorted Roll Transition Tubes were also plugged as a preventive measure.

• Fashion & Textile Research Journal
• /
• v.5 no.3
• /
• pp.260-266
• /
• 2003

The objective of this study is to compare the general body measurements and shoulder shapes of Korean and American elderly women to supply basic data for the apparel design. The anthropometrics data was collected including both direct and indirect measurements of 283 women over the age of 55 in Korean and the American women. The statistical methods used for the analysis of measurement data are the T-test, Exploratory data analysis, ANOVA and Duncan-test respectively. The results of the T-test indicated that there is a significant difference in the 14 body measurement items except of waist circumference. The results of exploratory data analysis, an independent relationship between shoulder slope angle and forward shoulder roll of Korean women. On the other hand, there is a dependent relationship that the bigger shoulder slope and forward shoulder roll with wide cross back shoulder of American women. Comparison of mean among the three different age groups, aged 55~59 group shows significant differences in the value of difference between cross back shoulders and horizontal shoulder width. This finding indicates that the wide and forward roll shoulder needs to special pattern making like ease amount and curvature for fit and comfort for women's apparel.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.91-96
• /
• 2001

When it is considered that many vehicle rides on the road and ride quality is an important method to evaluate vehicle performance with handling, running-over-bump manoeuvre may be suitable for testing ride quality. In this paper, a computed model has roughly steering system and lumped mass, connected by joint each rigid body, and suspension that has beam elements and has shock absorber as force element to represent nonlinear characteristics. A computer simulations for passing over a bump were made with two velocities. One side of vehicle passed over bump in due consideration of driver's habit that driver is subject to avoid a bad ride quality. On simulation, vertical acceleration, pitch angle and roll angle were measured at the mass center of chassis each case.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.11
• /
• pp.7377-7384
• /
• 2015

Agricultural tractors must have a function of ROPS to protect drivers under roll-over accident. In this study, finite element analyses and an optimal design were performed to reduce the cost and the production period of the cabin frame of a tractor to pass the ROPS strength test. To confirm the pass of ROPS strength test of an initial design model, the results of deformation and principal strain from the analyses were evaluated. To reduce the weight of the cabin frame, design of experiment of Taguchi was implemented, and an optimal design was obtained. The weight of the optimal design model was reduced by 7% comparing with the initial design model.

• Journal of Software Assessment and Valuation
• /
• v.16 no.1
• /
• pp.89-94
• /
• 2020

In this paper, we propose a software algorithm that can configure n-key roll-over that detects all keys without limitation on the number of pressed keys in the dynamic scanning detection of a keyboard composed of a matrix. The proposed algorithm uses the timer interrupt of the microcontroller for computer keyboard control, so that a constant and accurate detection interval can be obtained, and an accurate debounce time can be provided. In order to confirm the effectiveness of the proposed algorithm, a microcontroller was connected to a toy keyboard constructed in the form of a clavier and experiments were conducted. As a result of the experiment, it was confirmed that detection of all keys was performed accurately regardless of the number of keys pressed.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.2
• /
• pp.58-65
• /
• 1997

Work rolls used in cold rolling mills must have outstanding wear resistance and very little plastic defor- mation. Thus, these rolls require a higher surface hardness and harding to a greater depth. To meet these requirements, the rolls, in general, have basic chemical composition of 0.7 to 1.0% carbon and 1.0 to 5.0% Cr(chromium), plus a small amounts of special elements, and are subjected to intensive water quenching and tempering at low temperature to provide a surface hardness of over 90 shore. This test results are as follows. Deflection and fracture load of 5% Cr material are than those of 3% Cr material and show flat curve from surface to subsurface. It will be clear that 5% Cr work roll has a superior resisti- bility against wear and abrasion comparing with 3% Cr work roll. The improvement of wear and abrasion in 5% Cr work roll will be achieved by the large amount of wpheroidal carbide. In grindability and polish, 5% Cr work roll will be a little inferior comparing with 3% Cr work roll.