• 대한기계학회논문집A
• /
• 제36권12호
• /
• pp.1563-1568
• /
• 2012

인쇄전자는 RFID 나 유연 디스플레이 등의 전자회로나 소자를 인쇄방식으로 제작하는 공정이다. 특히 롤투롤과 같은 웹 이송방식 프린팅은 얇은 필름형태의 웹(Web)에 그라비아 인쇄나 고속 잉크젯과 같은 방법으로 이송중인 웹 상에 회로를 형성하는 공법이다. 이 공정은 생산단가가 저렴하고 고속생산이 가능하다는 이점이 있다. 다층구조를 가지는 회로나 디바이스를 생산할 때, 층과 층을 얼마나 정확하게 중첩시켜 인쇄하는가 하는 것은 인쇄된 전자회로의 집적도와 성능을 결정짓는 중요한 요소이다. 인쇄전자공법을 상용화하기 위해서 높은 중첩정밀도 구현이 선행되어야 한다. 본 연구에서는 롤투롤 인쇄방식에서 중첩정밀도의 향상을 위한 위치측정 시스템을 제안하고 신뢰성을 확인하였다. 또한 웹이 변형되었을 때의 측정 강인성도 실험적으로 확인하였다.

• 대한금속재료학회지
• /
• 제47권8호
• /
• pp.494-499
• /
• 2009

As a novel method to produce a steel beam with 6mm thickness for buildings, a continuous roll forming process is reported. The roll shape is asymmetric and consists of 6 pairs of rollers to bend the steel plate from $0^{\circ}$ to $90^{\circ}$. Results obtained upon application of the roll forming process showed that the angle of the section plate is $90^{\circ}$. However, defects such as bowing and camber as high as 3.2 [$^{\circ}/m$] were observed. A FEM (Finite Element Method) analysis was applied to investigate the causes of the results for the region between rollers no. 5 and no. 6. The results of a FEM simulation of deformation and stress showed that there are some strong peak stresses on the upper surface and bottom surface of the material. The positions of the peak stresses did not show a correspondence between the upper and bottom surfaces. Thus, the defects in the process of roll forming with a 6 mm thick steel plate occur by the unbalanced stresses between the upper surface and bottom surface of the material in this study.

• 한국재료학회지
• /
• 제33권12호
• /
• pp.565-571
• /
• 2023

AA1050/AA6061/AA1050 layered sheet was fabricated by cold roll-bonding process and subsequently T4 and T6 aging-treated. Two commercial AA1050 sheets of 1 mm thickness and one AA6061 sheet of 2 mm thickness were stacked up so that an AA6061 sheet was located between two AA1050 sheets. After surface treatments such as degreasing and wire brushing, they were then roll-bonded to a thickness of 2 mm by cold rolling. The roll-bonded Al sheets were then processed by natural aging (T4) and artificial aging (T6) treatments. The as roll-bonded Al sheets showed a typical deformation structure, where the grains are elongated in the rolling direction. However, after the T4 and T6 aging treatments, the Al sheets had a recrystallized structure consisting of coarse grains in both the AA5052 and AA6061 regions with different grain sizes in each. In addition, the sheets showed an inhomogeneous hardness distribution in the thickness direction, with higher hardness in AA6061 than in AA1050 after the T4 and T6 age treatments. The tensile strength of the T6-treated specimen was higher than that of the T4-treated one. However, the strength-ductility balance was much better in the T4-treated specimen than the T6-treated one. The tensile properties of the Al sheets fabricated in the present study were compared with those in a previous study.

• 대한기계학회논문집A
• /
• 제35권8호
• /
• pp.855-861
• /
• 2011

본 연구에서는 극박 압연 이론과 6 단 압연기 수식 모델을 이용하여 압연 후 판 형상 예측에 대하여 제안하였다. 폭 방향에서 롤 사이의 접촉 압력과 판과 워크롤 사이의 압연하중은 6 단 압연기의 형상학적 구조와 경계조건을 이용한 수식모델을 통하여 계산된다. 그리고 압연 방향의 압연하중 분포는 Fleck 의 극박 압연 이론을 이용하여 계산하였다. 워크롤의 3 차원 탄성 변형량은 폭 과 압연방향의 압력분포에 의하여 계산된다. 이때, 3 차원 판 형상은 워크롤의 탄성변형에 의하여 얻어진다. 또한 3 차원 판 형상은 극박 압연 실험과 유한요소해석을 통하여 검증하였다.

• 한국기계가공학회지
• /
• 제7권3호
• /
• pp.12-16
• /
• 2008

The state of deformation and stress and the structural safety are studied at the main frame composed with car body by the impact of front, offset and overturn in this study. The values of maximum deformation and von-Mises stress in case of offset impact are 2 to 3 times as high as those in case of front or offset impact at the parts of front and middle legs of roll cage. The case of front impact is of the greatest safety as compared with the case of offset or overturn impact. As there is a great stress on the side in case of overturn impact, this value is more than 2 times as low as that in case of offset impact. But there is a great possibility of overturn by the buckling on both sides in case of overturn impact.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.319-322
• /
• 2003

For the analysis of leveling process by the 3-dimensional elastic-plastic finite element method, a finite element analysis program modeling large deformation of shell has been developed. This program fur analyzing large deformation of sheet during leveling includes spring-back analysis as well as efficient contact treatment between sheet and rolls of leveler. This is verified by the simple leveling experiment with 5 rolls at laboratory. Besides the leveling examples, problems within the category of large strain and rotation, such as 3-dimensional roll-up and gutter occurrence at continuous bending-unbending process are also tested for verification of the program. The residual curvatures of strip predicted by finite element analysis are within 20% error range of the experiment. The formation and direction of anticlastic curvature or gutter during bending-unbending under tension is predicted and this agrees with the experimental results.

• 소성∙가공
• /
• 제25권1호
• /
• pp.56-60
• /
• 2016

Precise prediction and control of the strip profile is crucial for automatic process set-up and operation of a hot strip mill. In the current study, we present the effect of post-deformation on the steady-state strip profile. The process was simulated by a 3-D elastic-plastic finite element (FE) analysis. Comparisons are made between the strip profile measured at the roll exit and the steady-state strip profile. The results raised an issue with regard to the importance of taking into account the effect of post-deformation.

• 소성∙가공
• /
• 제6권2호
• /
• pp.118-135
• /
• 1997

In order to analyze the deformation and residual curvature of steel sheets in the strip processing lines, a program for calculating curvature and work hardening of sheet was developed. Strip deformation caused by repeated bending under tension in the process lines was analyzed on the basis of the incremental-plasticity theory with the mixed hardenting model for the purpose of predicting the strip shape and the yield stress change. The developed calculation program was applied to predict curl and gutter of sheets within a 10% difference. The yield stress increment was also predicted with the similar accuracy. Application of the model to tension legvelling process showed that gutter could be controlled by intermesh and elongation. The yield stress increment in the electro-galvanizing line calculated by the developed program was found to be dependent on the yield strength, the applied tension and the diameter of the smallest roll.

• International Journal of Precision Engineering and Manufacturing
• /
• 제6권4호
• /
• pp.55-59
• /
• 2005

This paper presents a feasibility study whether Shida's constitutive equation being widely used for plain carbon steel in steel manufacturing industry can be extended to alloy steels with a due carbon equivalent model. T,he constitutive relation of the alloy steels (SAE9254, AISI52100 and AISI4140) is measured using hot deformation simulator (GLEEBLE 3500C) at high temperatures ($800^{\circ}C{\~}1000^{\circ}C$) within strain rates of $0.05{\~}40\;s^{-1}$. It has been found the predicted flow stress behavior (constitutive relation) of AISI52100 steel is in agreement with the measured one. On the other hand, the measured flow stress behavior of SAE9254 and AISI4140 steel partly concords with the predicted one when material experiences relatively high strain rate ($10{\~}40\;s^{-1}$) deformation at low temperature ($800^{\circ}C$). It can be deduced that, for AISI52100 steel, Shida's equation with the carbon equivalent model can be applicable directly to the roughing and intermediate finishing stand in hot rolling process for calculating the roll force and torque.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.432-435
• /
• 2005

Extensive width reduction of slabs is an important technology to achieve continuous production between the steelmaking and hot rolling processes. Conventionally, a vertical roll process has been used to achieve extensive width reduction. However, it is impossible to avoid the defects such as dog-bone, fish tail and camber. The deformation behavior in the width sizing process is more favorable than that in conventional vertical rolling edger, i.e. the material better flows toward the center of slab. This study is carried out to investigate the deformation of slab by two-step sizing press. The FE-simulation is utilized to predict plastic deformation mode in compression by a sizing press of slabs far hot rolling. In this paper, the various causes of the asymmetrical rolling phenomena are mentioned for the purpose of understanding of rolling conditions. Analytical results of slab-deformation by sizing press are presented below in this study.