• Journal of Auto-vehicle Safety Association
• /
• v.14 no.2
• /
• pp.57-69
• /
• 2022

Recently, as interest in self-driving cars has increased worldwide, research and development on the Advanced Driver Assist System is actively underway. Among them, the purpose of Adaptive Cruise Control (ACC) is to minimize the driver's driving fatigue through the control of the vehicle's longitudinal speed and relative distance. In this study, for the research of the ACC test in the real environment, the real-road test was conducted based on domestic-road test scenario proposed in preceding study, considering ISO 15622 test method. In this case, the distance measurement method using the dual camera was verified by comparing and analyzing the result of using the dual camera and the result of using the measurement equipment. As a result of the comparison, two results could be derived. First, the relative distance after stabilizing the ACC was compared. As a result of the comparison, it was found that the minimum error rate was 0.251% in the first test of scenario 8 and the maximum error rate was 4.202% in the third test of scenario 9. Second, the result of the same time was compared. As a result of the comparison, it was found that the minimum error rate was 0.000% in the second test of scenario 10 and the maximum error rate was 9.945% in the second test of scenario 1. However, the average error rate for all scenarios was within 3%. It was determined that the representative cause of the maximum error occurred in the dual camera installed in the test vehicle. There were problems such as shaking caused by road surface vibration and air resistance during driving, changes in ambient brightness, and the process of focusing the video. Accordingly, it was determined that the result of calculating the distance to the preceding vehicle in the image where the problem occurred was incorrect. In the development stage of ADAS such as ACC, it is judged that only dual cameras can reduce the cost burden according to the above derivation of test results.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.39 no.6
• /
• pp.363-369
• /
• 2021

High-definition road maps are used as the basic infrastructure for autonomous vehicles, so the latest road information must be quickly reflected. However, the current drawing and structural editing process of high-definition road maps are manually performed. In addition, it takes the longest time to generate road lanes, which are the main construction targets. In this study, the point cloud of the road lane markings, in which color types(white, blue, and yellow) were predicted through the PointNet model pre-trained in previous studies, were used as input data. Based on the point cloud, this study proposed a methodology for automatically drawing and structural editing of the layer of road lane markings. To verify the usability of the 3D vector data constructed through the proposed methodology, the accuracy was analyzed according to the quality inspection criteria of high-definition road maps. In the positional accuracy test of the vector data, the RMSE (Root Mean Square Error) for horizontal and vertical errors were within 0.1m to verify suitability. In the structural editing accuracy test of the vector data, the structural editing accuracy of the road lane markings type and kind were 88.235%, respectively, and the usability was verified. Therefore, it was found that the methodology proposed in this study can efficiently construct vector data of road lanes for high-definition road maps.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.3
• /
• pp.1098-1104
• /
• 2011

This paper presents the development of the surface profile sensing system (SPSS) and its application to analysis of road surface. The SPSS which can robustly reconstruct the road input profiles from the intermixed data with the vehicle's dynamic motion, is implemented using the multi-sensor system with the optimally shaped transfer function. The performance of this system is evaluated by a series of experimental works in the devised simulator. And a real car test equipped with the proposed system is performed in the proving ground over both deterministic and random road surfaces. Finally, a feasibility of the system is investigated considering the road model.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.46 no.5
• /
• pp.117-127
• /
• 2004

A risk analysis on the cutting slope of roads near Cheongju area was carried out with the data from geological map, field investigation, and laboratory test and with the Geographic Information System. A risk analysis method on the cutting slope of road using the Geographic Information System was developed with the data from geological map, field investigation and laboratory tests. In the GIS, road factors which are safety factor, class of road, slake index, slope-protection works, and height of slope in the cutting slopes are classified into some ranks, and their weighting factors were taken into account. This method can be applied effectively to a road management.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.52 no.9
• /
• pp.526-532
• /
• 2003

This paper describes a recognition method of a road direction for an autonomous vehicle based on magnetic sensors. Using the sensors mounted on a vehicle and the magnetic markers embedded along the center of road, the autonomous vehicle can recognize a road direction and control a steering angle. Using the front lateral deviation of a vehicle and the rear one, the road direction is calculated. The analysis of magnetic field, the acquisition technique of training data, the training method of neural network and the computer simulation are presented. According to the computer simulation, the proposed method is simulated, and its performance is verified. Also, the experimental test is confirmed its reliability.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.4
• /
• pp.381-389
• /
• 2010

Modern military equipments are often required to be mounted on a truck for their survivability and operation performance. Special units installed on the truck at times experience serious shock vibration caused by obstacles of road and/or uncommon road shape. It is then essential to analyze the travel performance of truck-mounted special units for their survivability and performance. In this paper, shock responses of the equipments subjected to bump passing and wash board road are experimentally obtained and also analyzed via FEM. Modified bump configuration and road profile considering the interface with tire are suggested. Analytical results considering this modification show good agreement with test results.

• Journal of Auto-vehicle Safety Association
• /
• v.4 no.1
• /
• pp.5-11
• /
• 2012

This paper discusses the evaluation of the safety impact of the Adaptive Cruise Control (ACC) system in Korea. To evaluate the safety impact, this paper suggests an analysis method by using the test scenario and field operational test data. The test scenario is composed to represent the main component factor of the ACC system and ACC related accident situation such as rear-end collision, lane-change, and road-curvature, etc. Also, from the field operation test data, the system's potential to increase the safety can be measured ideally. Besides, field operational testdata was used to revise the expected safety impact value as Korean road conditions. By using the proposed evaluation method, enhanced safety impact of the ACC system can be estimated scientifically.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.13 no.4
• /
• pp.48-56
• /
• 2014

Even though vehicle types, gradient, pavement conditions and types of pavement should be considered for estimating fuel consumption, existing models were developed as a function of vehicle types and vehicle speed. Therefore in this study, the model of fuel consumption was developed using field test data in order that effect analysis on the passenger vehicle fuel consumption by road gradient. At first, fuel consumption was measured in second-based, using GPS device and fuel consumption measurement device for development of fuel consumption model considered road gradient. The road gradient was classified as flatland, up-hill and down-hill. Development of model was using by regression model which vehicle speed(km/h) and fuel consumption(${\ell}/km$). The on-road test proved that fuel consumption of passenger vehicle is affected by road gradient.

• International Journal of Highway Engineering
• /
• v.14 no.3
• /
• pp.141-149
• /
• 2012

This paper attempts to evaluate driving stability by the vibration of human body. The purpose of this research is to establish an evaluation methodology for controling the quality of road surface. The study was conducted to investigate the relationship between road surface profiles (IRI, International Roughness Index) and the fatigue caused by the vibration of human body. Furthermore, 3-axis acceleration in driving vehicles was examined based on sampling sections under various road conditions. The acceleration value of frequency bands were analyzed by the characteristics of road surface, and realized the range of human influence by conditions and type of road surface with ISO-2631 standards. In general, more human fatigue by vehicle vibration was appeared in concrete pavements with high IRIs based on the analysis from given test data. Whereas, The SMA asphalt pavement and the diamond grinded concrete pavement reduce the human fatigue.

• Korean Journal of Agricultural Science
• /
• v.45 no.2
• /
• pp.177-184
• /
• 2018

The frost heave process from repeated freezing and thawing actions in winter on forest road cut-slopes is important for forest road maintenance and management. This study investigated the damages of the forest heave process on forest road cut-slopes by measuring the changes in the road-cut surface elevation and sediment production and by conducting vegetation surveys which were aimed at providing information for forest road maintenance plans. The temperature and humidity differences were determined between the north and south cut-slopes. T-test showed that the north slope had a lower temperature and humidity than that of the south slope. Field observations also confirmed frozen soils on the north slopes, indicating that the north slopes are susceptible to frost heave. Sediment was converted to dry weight per unit area ($g/m^2$). T-test showed that the north slope produced more sediment than that of the south slope. The study confirmed that more frost heave occurred on the north cut-slopes than on the south cut-slopes. Vegetation surveys were conducted on five cut-slope plots. Considering the dominant species found above the cut-slopes, vegetations in all the plots are expected to succeed to pine and oak in the future. The dominant species appearing on the cut-slopes of the study area were exotic species because the elapsed time of the site was only 2 - 4 years.