• Journal of Korean Academy of Fundamentals of Nursing
• /
• v.5 no.1
• /
• pp.143-154
• /
• 1998

Background : There have been very few studies conducted on the number and type of microorganisms that remain on the ring finger after handwashing. This study was performed to investigate whether there were changes and differences in the type and number of microorganisms on the ring finger before and after handwashing. Method : The subjects of the study were 15 MICU and SICU staff nurses who were wearing rings. I swabbed two different fingers of the same hand with cotton balls. One finger which had a ring and the other with no ring. I swabbed the fingers of each subject three times(before handwashing, after handwashing with soap, and after handwashing with bethadine solution). After storing them for 48 hours in an incubator, I sent them to the laboratory and recorded the culture results. Results : There was no difference in the type of microorganism, but a major difference in the number of the microorganisms that existed on the finger ring. The results showed that there were much more microorganisms on the ring fingers than on the fingers that did not have rings both before and after handwashing. This tendency was consistent regardless of the handwashing agent. I therefore recommend that all nursing staff who work in general nursing units, as well as nurses who work in the ICU, remove their rings when taking care of the patients.

• Bulletin of the Korean Mathematical Society
• /
• v.39 no.4
• /
• pp.645-652
• /
• 2002

In this note we investigate some results which concern the types of local rings. In particular it is shown that if the type of a quasi-unmixed local ring A is less than or equal to depth A ＋ 1, and $\hat{A}_p$ is Cohen-Macaulay for every prime $p\neq\hat{m}$, then A is Cohen-Macaulay. (This implies the previously known result: if A satisfies $(S_{n-1})}$, where n is the type of a .ins A, then A is Cohen-Macaulay.)

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.8
• /
• pp.1581-1586
• /
• 2012

In this paper, a novel resonator using ring type DGS is proposed for improvement of phase noise characteristics that is weak point of oscillator using planar type microstrip line resonator, and oscillator for 5.8GHz band is designed using proposed DGS resonator. The ring type DGS resonator is composed of DGS cell etched on ground plane under $50{\Omega}$ microstrip line. At the fundamental frequency of 5.8GHz, 7.6dBm output power and -82.7 dBc@100kHz phase noise have been measured for oscillator with ring type DGS resonator. The phase noise characteristics of oscillator is improved about 9.5dB compared to one using the general ${\lambda}/4$ microstrip resonator. Because it is possible that varactor diode or lumped capacitor is placed on the gaps of ring type DGS, resonant frequency can be controlled by bias voltage. We can design voltage controlled oscillator using proposed ring type DGS resonator. Thus, due to its simple fabrication process and planar type, it is expected that the technique in this paper can be widely used for low phase noise oscillators for both MIC and MMIC applications.

• Progress in Superconductivity and Cryogenics
• /
• v.11 no.1
• /
• pp.49-54
• /
• 2009

This paper presents the numerical simulation results on the moving type electrodynamic suspension (EDS) simulator and static type EDS simulator using high-Tc superconducting (HTS) levitation magnet. The levitation force of the EDS system is formed by the reaction between the moving magnet and the fixed ground conductor. The possible two ways to simulate the EDS system were simulated in this paper by using finite element method (FEM). The first way was the moving type simulator which consists of the fixed HTS magnet and the moving ground conductor. The second way was the static type simulator which consists of the fixed magnet, the fixed ground conductor and the ac current supply system. To verify the characteristics of high speed EDS system with the moving type simulator heavy, large and fast moving ground conductor is needed. The static type simulator can get the characteristics of the high speed EDS system by applying equivalent ac current to velocity, therefore it does not need large moving part. The static type EDS simulator, which can consist of an HTS magnet, the fixed ground conductor(s), an AC power supply and the measuring devices, also test the effect of the shape of the ground conductor easily. The plate type ground conductor made stronger levitation force than ring type ground conductor. Although the outer diameter 335 mm ring type ground conductor (Ring3) was larger than the outer diameter 235 mm ground conductor (Ring2), the levitation force by Ring2 was stronger than that by Ring3. From the calculation results on this paper, the consideration of the magnetic flux distribution according to the levitation height should be included in the process of the ground conductor design.

• Tribology and Lubricants
• /
• v.11 no.2
• /
• pp.24-33
• /
• 1995

This paper presents the contact stress distributions between the multi-contact bodies and the total reaction forces for various types of contact geometry for multi-load slewing ring bearings. The FEM results indicate that the slope of the roller type of slewing ring bearing has slightly steeper than that of the ball type. This is because the roller type wire race bearings is stiffer than the ball type bearing. The total reaction force of ball type slewing bearing shows much higher than that of wire race slewing bearings.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.7
• /
• pp.479-485
• /
• 2001

In this paper, we propose optical subcarrier mutiplexing(SCM) transceiver module for base station(BS) that has no optical source and can be used for full-duplex communication over single optical fiber. In this method we retransmit optical modulated signal to the central office(CO) using loop-back system with a ring type Mach-Zehnder modulator(MZM) in BS, where optical source is transmitted from the CO. We have modeled the ring type MZM and were conformed that the measured results were in good agreement with the modeling. In the ring type MZM, the optical symmetric position of the MZM is very important in RF signal transmission.

• Tribology and Lubricants
• /
• v.14 no.3
• /
• pp.59-64
• /
• 1998

This paper presents the deformation characteristics of cam ring in a balanced type vane pump. Cam ring is operated in the high-pressure condition. Therefore the local deformation of cam ring affects the characteristics of compression, vane motion and noise and vibration. We analyzed the deformation of cam ring for the three types by using the finite element method. The deformed shape of cam ring and the effects of deformation on the compression are presented. As a result of analysis, we know that the right hole of the cam ring has advantage for reducing the pressure overshoot.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.671-674
• /
• 2004

This paper presents design and analysis of multi-layered ring-dot type piezoelectric transformer. These transformers are useful for step up and step down. The transformers consist of disk type multi-layered piezoelectric ceramic plates. The finite element method(FEM) was used for analysis transformer. Vibration mode, electric field and equivalent elastic strain of piezoelectric transformer were simulated by changing frequency. As results, the strain was distributed in isolation part entirely. We can get the operated in step up transformer when the inner side electrode using by input parts. Also we can get the step down transformers using by input Part as outer side electrode. The step up ratio and step down ratio was increased by decreasing inner side electrode. The resonance frequency was increased by increasing inner side electrode when the transformer was operated in step down transformer. But the step up one was decreased. From these results, we can expect to multi-layered ring-dot type piezo transformers as step up and step down transformers.

• Journal of the Korean Society of Safety
• /
• v.22 no.3 s.81
• /
• pp.45-50
• /
• 2007

In this study, reinforcing effects of umbrella-type shell roofs structures such as stadium, exhibition, auditorium and museum are analyzed. Umbrella-type shell roofs treated in this study are practical shapes of conical shells. The objective of this study is to analyze reinforcing effects of umbrella-type shell roofs with stiffeners. Various locations of stiffeners, that is, edge ring A, B, center ring, junction stringer and center stringer are presented and the effects of reinforcement is examined. Also, the reduction effects of roofs thickness by stiffeners are examined. It is shown that the thickness of roofs can be reduced about $20{\sim}30%$ by junction stringer and more than 60% by edge ring A.

• Journal of electromagnetic engineering and science
• /
• v.3 no.2
• /
• pp.104-110
• /
• 2003

A ring filter is proposed as a wide-banded filter. It consists of a ring and two short stubs, which are connected at 90$^{\circ}$ and 270$^{\circ}$ points of the ring. Since the termination impedance at 90$^{\circ}$ and 270$^{\circ}$ points of the ring and the characteristic impedance of the short stub have an effect on designing of it, the relation between them and bandwidths has been studied. Based on the study, two types of small-sized wideband CVT(constant VSWR-type impedance transformer)- and CCT(constant conductance-type impedance transformer)-ring filters are introduced, designed, simulated and one of two, a CCT -ring filter, is tested. The circumference of the ring can be reduced theoretically up to 60$^{\circ}$ and two of many cases having about 300$^{\circ}$ circumferences are simulated. The simulated results show more than 100 % fractional bandwidth, which can be obtained with more than 5 stages in conventional filter-design techniques. To test the designed CCT-ring filter, it has been fabricated in microstrip technology and the measured results show good agreement with the simulated ones, having more than 100 % fractional bandwidth.