• 한국진공학회지
• /
• 제12권4호
• /
• pp.269-274
• /
• 2003

The electrical, optical and structural properties of ZnNiO thin _ films deposited on Si substrates using rf-magnetron sputtering method have been investigated before and after the thermal annealing processes. The crystallinity of the ZnNiO thin film become degraded with increasing the Ni contents. This is mainly because the lattice of the thin film was expanded due to the oxygen-deficient conditions. Concerning the electrical properties of the thin film, the carrier concentration increases ($6.81\times10^{14}\textrm{cm}^{-2}$) and Hall mobility decreases (36.3 $\textrm{cm}^2$/Vㆍs) with higher doping concentration of Ni. However, the carrier concentration and Hall mobility became low ($1.10\times10^{14}\textrm{cm}^2$ and high (209.6 $\textrm{cm}^2$/Vㆍs), respectively, after the thermal annealing process at $1000 ^{\circ}C$. We also observed a strong luminescene center peaking at 546 nm in photoluminescence spectra, which was caused by a deep level center in the ZnO band gap with oxygen deficient ZnNiO structure.

• 한국전기전자재료학회논문지
• /
• 제28권10호
• /
• pp.620-624
• /
• 2015

We have studied structural, optical and electrical properties of In-Ga-doped ZnO (IGZO) thin films. The IGZO thin films were deposited on the corning 1737 glass by RF magnetron sputtering method. The RF power in sputtering process was varied as 30, 50, 70, and 90 W respectively. All of the IGZO thin films transmittance in the visible range (400 nm ~ 800 nm) was above 83%. XRD analysis showed the IGZO thin films amorphous structure of the thin films without any peak. And also IGZO thin film have low resistivity ($1.99{\times}10^{-3}{\Omega}cm$), high carrier concentration ($6.4{\times}10^{20}cm^{-3}$), and mobility ($10.3cm^2V^{-1}s^{-1}$). By the studies we found that IGZO transparent thin film can be used as optoelectronic material and introduced application possibility for future electronic devices.

• 한국진공학회지
• /
• 제21권1호
• /
• pp.17-21
• /
• 2012

투명전도산화막인 Ga-도핑된 ZnO (GZO) 박막을 RF 마그네트론 스퍼터링 증착법을 이용하여 증착하고 전기적, 광학적 특성을 연구하였다. 증착변수로 공정압력에 변수를 주었으며 공정 압력 변화에 따라 전기적 특성과 광학적 특성이 달라짐을 확인할 수 있었다. 모든 박막은 공정압력에 상관없이 c-축(002) 방향성을 나타냈다. 증착된 GZO 박막의 전기저항성은 $8.68{\times}10^{-3}{\Omega}{\cdot}cm\sim2.18{\times}10^{-3}{\Omega}{\cdot}cm$이었고, 모든 가시광 영역에서 90% 이상의 평균 투과율을 보였다. 공정압력에 따라 상온에서 증착된 GZO 박막은 우수한 낮은 저항성과 높은 투과율을 나타내었고, 평판디스플레이와 태양전지의 투명전극으로 응용되기에 적합한 특성을 지닌 것을 확인 할 수 있었다.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.77-82
• /
• 1995

PTCR(Positive Temperature Coefficient of Resistivity) thermistor in thin film BaTiO$_{3}$ system was prepared by using radio frequency(13.56 MHz) and DC magnetron sputter equipment. Polycrystalline, surface structure, and R-T(Resistivity-Temperature) characteristics of the specimens were measured by X-ray diffraction(D-Max3, Rigaku, Japan), SEM(Scanning Electron Microscopy: M.JSM84 01, Japan), and insulation resistance measuring system (Keithley 719), respectively. Thin films characteristics of the thermistor showed different properties depending on the substrate even with the same sputtering condition. The thin film formed on the A1$_{2}$O$_{3}$ substrate showed a good crystalline and a low resistivity at below curie point. However, the thin films prepared on slide glass and Si wafer were amorphous. The thicknesses of the three samples prepared under the same process conditions were 700[.angs.], 637.75[.angs.], and 715[.angs.], respectively.

• 한국전기전자재료학회논문지
• /
• 제20권3호
• /
• pp.202-206
• /
• 2007

ZnO is a promising material to make high efficient ultraviolet(UV) or blue light emitting diodes(LEDs) because of its large binding energy and energy bandgap. In this study, we prepared ZnO thin films with p-type conductivity on silicon(100) substrates by RF magnetron sputtering in the mixture of $N_2$ and $O_2$. The process was accompanied by low pressure in-situ annealing in $O_2$ at $600^{\circ}C$ and $800^{\circ}C$ respectively. Hall effect in Van der Pauw configuration showed that the N-doped ZnO film annealed at $800^{\circ}C$ has p-type conductivity. Photoluminescence(PL) spectrum of the film annealed at $800^{\circ}C$ showed UV emission related to exciton and bound to donor-acceptor pair(DAP) as well as visible emission related to many intrinsic defects.

• 한국재료학회지
• /
• 제22권2호
• /
• pp.86-90
• /
• 2012

Insoluble catalytic electrodes were fabricated by RF magnetron sputtering of Pt on Ti substrates and the performance of seawater electrolysis was compared in these electrodes to that is DSA electrodes. The Pt-sputtered insoluble catalytic electrodes were nearly 150 nm-thick with a roughness of $0.18{\mu}m$, which is 1/660 and 1/12 of these values for the DSA (dimensionally stable anodes) electrodes. The seawater electrolysis performance levels were determined through measurements of the NaOCl concentration, which was the main reaction product after electrolysis using artificial seawater. The NaOCl concentration after 2 h of electrolysis with artificial seawater, which has 3.5% NaCl normally, at current densities of 50, 80 and 140 mA/$cm^2$ were 0.76%, 1.06%, and 2.03%, respectively. A higher current density applied through the electrodes led to higher electrolysis efficiency. The efficiency reached nearly 58% in the Pt-sputtered samples after 2 h of electrolysis. The reaction efficiency of DSA showed higher values than that of the Pt-sputtered insoluble catalytic electrodes. One plausible reason for this is the higher specific surface area of the DSA electrodes; the surface cracks of the DSAs resulted in a higher specific surface area and higher reaction sites. Upon the electrolysis process, some Mg- and Ca-hydroxides, which were minor components in the artificial seawater, were deposited onto the surface of the electrodes, resulting in an increase in the electrical resistances of the electrodes. However, the extent of the increase ranged from 4% to 7% within an electrolysis time of 720 h.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.360.2-360.2
• /
• 2016

CuSn thin films were fabricated by rf magnetron co-sputtering method on the Si(100) substrate for evaluation of the antibacterial effect. The co-sputtering process was performed with different rf powers and sputtering times to regulate the thickness of the films and relative atomic ratio of Cu to Sn. The physicochemical properties of the CuSn thin films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), X-ray induced Auger electron spectroscopy (XAES), Optical microscope (OM), 4-point probe, and antibacterial test. An antibacterial test was conducted with Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) as changing contact times between CuSn fillms and bacteria suspension. We compared to the crystalline structures of films before sterilization and after sterilization by XRD measurement. The changes of oxidation states of Cu and Sn and the chemical environment of films before and after antibacterial test were investigated with high resolution XPS spectra in the regions of Cu 2p, Cu LMM, and Sn 3d. After antibacterial test, the morphology of the films was checked with an OM images. The electrical properties of the CuSn films such as surface resistance and conductivity were measured by using 4-point probe.

• 한국진공학회지
• /
• 제18권3호
• /
• pp.213-220
• /
• 2009

Al이 도핑된 투명 전도성 Al:ZnO (AZO) 박막에 대한 RF magnetron sputtering 증착 법을 이용한 저온 최적공정조건을 연구하였다. 투명전극 재료로써의 AZO 박막의 전기적, 결정학적 물성을 최대한 향상시키기 위해서, in-situ상태에서 유리기판상에 최적화된 증착 조건의 AZO 버퍼 층을 삽입하는 이중박막 구조를 제작하였다. RF 인가 전력 $50{\sim}60\;W$에서 증착된 버퍼층 위에 120 W의 RF 전력에서 성장한 AZO 박막의 경우, 비저항 $3.9{\times}10^{-4}{\Omega}cm$, 전하 캐리어농도 $1.22{\times}10^{21}/cm^3$, 홀 이동도 $9.9\;cm^2/Vs$의 전기적 특성을 보였다. 이러한 결과는 버퍼 층이 없는 기존의 단일 구조와 비슷하나, 전기적 비저항 특성을 약 30% 정도 향상시킬 수 있었으며, 전기적 특성의 향상 원인을 $Ar^+$ 이온의 입사 에너지의 변화에 따른 버퍼 층의 압축응력과 결정화 정도와의 의존성으로 설명하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.675-675
• /
• 2013

CIGS thin films have received a great attention as a promising material for solar cells due to their high absorption coefficient, appropriate bandgap, long-term stability, and low cost production. CIGS thin films have been deposited by various methods such as co-evaporation, sputtering, spray pyrolysis and electro-deposition. In this study, Cu(In,Ga)Se2(CIGS) thin films were prepared using a single quaternary target by rf magnetron sputtering. The effect of sulfurization on the structural, compositional and electrical properties of the films was examined in order to develop the deposition process. An optimal sulfurization process will be selected for the preparation of CIGS thin films with good structural, optical and electrical properties by applying various sulfurization processes. In addition, the electrical properties of CIGS thin films were investigated by post-deposition annealing process. The carrier concentration of CIG(SSe) thin films after sulfurization was increased from $10^{14}cm^{-3}$ to $10^{16}cm^{-3}$ and the resistivity was increased from 10 ${\Omega}cm$ to $10^3$ ${\Omega}cm$. It is confirmed that CIG(SSe) thin films prepared at optimal deposition condition have similar atomic ratio to the target value after sulfurization.

• Progress in Superconductivity
• /
• 제4권2호
• /
• pp.153-156
• /
• 2003

We have studied fabrication of $MgB_2$ thin film on $SrTiO_3$ (001) and r-cut $A1_2$$O_3$ substrates by rf magnetron sputtering method using and $ MgB_2$ single target and two targets of Mg and B, respectively. Based on P -T phase diagram of $MgB_2$ and vapor pressure curves of Mg and B, a three-step process was employed. B layer was deposited at the bottom to enhance the film adhesion to the substrate. Secondly, co-sputtering of Mg and B was done. Finally, Mg was sputtered on top to compensate fur the loss of Mg during annealing. Subsequently, $MgB_2$ films were in-situ annealed in various conditions. The sample fabricated using the three-step process showed $T_{c}$ of 24 K and formation of superconducting $MgB_2$ phase was confirmed by XRD spectra. In case of co-sputtering deposition, $T_{c}$ depended on annealing time and argon pressure. However, those made by single-target sputtering showed non-superconducting behavior or low transition temperature, at best.est.