• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.21-24
• /
• 2000

This paper introduces the design and implementation of a Ku-band 5-bit monolithic phase shifter with a ceramic package. The 5-bit phase shifter MMIC was designed and fabricated by using GaAs MESFET switches. The packaged phase shifter demonstrates a phase error less than 11.3 $^{\circ}$ RMS and an insertion loss variation less than 1.0㏈ RMS for 13∼15㎓. For all 32 states, an insertion loss is measured to be 12.2${\pm}$2.2㏈, an input return loss more than 5.0㏈, and an output return loss more than 6.2㏈ from 13㎓ to 15㎓. The chip size of the 5-bit phase shifter MMIC is 2.35${\times}$1.65mm$\^$2/ including digital control circuits. The size of the ceramic packaged phase shifter is 7.2${\times}$6.2mm$\^$2/.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.6
• /
• pp.598-601
• /
• 2004

A microstrip filter has been designed and fabricated in hairpin form on a GaAs substrate and its characteristics such as the insertion loss, return loss, and bandwidth have been investigated. The presented filter is realized with relatively small size, 4.5 by 3.6 mm. The insertion loss and return loss of the filter are 1.17 dB and 30 dB, respectively. The filter exhibits 3 dB-bandwidth of 350 MHz at the center frequency, 5.890 GHz. The experimental results show good agreement with the numerical ones. However, the measured center frequency is about 100 MHz higher than the designed one.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.377-382
• /
• 2000

Film bulk acoustic resonator (FBAR) using AIN reactively sputtered at room temperature was fabricated. The FBAR is composed of a piezoelectric aluminium nitride thin film, top electrode of Al and bottom electrode of Au connected by a short (200${\mu}{\textrm}{m}$) transmission line on both sides and reflector layers of SiO$_2$- W Pair. The active areas of Al and Au were patterned using 150${\mu}{\textrm}{m}$ diameter shadow mask. The series resonance frequency (fs) and the parallel resonance frequency (fp) were measured at 1.976 GHz and 2.005 GHz, respectively. The minimum insertion loss and return loss were 6.1 dB and 37.19 dB, and the quality factor (Q) was 4261.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.5
• /
• pp.549-556
• /
• 2015

In this paper, design and fabrication for inset fed microstrip patch antennas applied to the $3{\times}3$ array CSLR and eight CSLR, respectively, to the ground plane are studied. The theoretical results are compared to the experimental results for the return loss and radiation pattern. For 'CSLR 09' antenna, the theoretical result for the resonant frequency and the return loss are 2.82 GHz and - 25.35 dB, respectively. The experimental results are obtained for a 2.885 GHz, -30.72 dB. Theoretical results for the resonant frequency and the return loss of the 'CSLR 08' antenna are 2.82 GHz, -16.77 dB, respectively, and the experimental results are obtained for a 2.885 GHz, -14.90 dB. In addition, E-plane and H-plane radiation patterns in comparison with designed and fabricated antennas are in good agreement.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.4A
• /
• pp.408-416
• /
• 2010

A dumbbell-type CPW transmission-line structure has been proposed to improve the return loss of the transmission line between a driver IC and flip-chip-bonding VCSEL(Vertical Cavity Surface Emitting Laser) in a hybrid opto-electric circuit board(OECB). The proposed structure used a pair of dummy ground solder balls on the ground lines for flip-chip bonding of the VCSEL and designed the dumbbell-type CPW transmission line to improve reflection characteristics. The simulated results revealed that the return loss of the dumbbell-type CPW transmission line was 13-dB lower than the conventional CPW transmission line. A 4-dB improvement in the return loss was obtained using the dummy ground solder balls on the ground lines. The variation rate of the reflection characteristic with the variation of terminal impedances of the transmission line (at the output terminal of the driver IC and the input terminal of the VCSEL) is about ${\pm}2.5\;dB$.

• Journal of electromagnetic engineering and science
• /
• v.16 no.3
• /
• pp.150-158
• /
• 2016

This paper reports on a study of LiNiZn-ferrite composite as a radiation absorbent material (RAM). The electromagnetic (EM) wave absorbers are composed of an EM wave absorbing material and a polymeric binder. The surface morphology, chemical composition, weight percent of the ferrite composite of the toroid sample, magnetic properties, and return loss are investigated using field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), vibrating sample magnetometer (VSM), and network analyzer. For preparing the absorbing sheet, chlorinated polyethylene (CPE) is used as a polymeric binder. The EM wave absorption properties of the prepared samples were studied at 4 - 8 GHz. We can confirm the effects of the thickness of the samples for absorption properties. An absorption bandwidth of more than a 10-dB return loss shifts toward a lower frequency range along with an increase in the thickness of the absorber.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.1
• /
• pp.193-198
• /
• 2009

In this paper, we report the design of UHF RFID ceramic antenna using HFSS, one of the widely used RFID design tools. Of the developed antenna system, we analyze its Return Loss using HFSS and its characteristics using Smith Chart methodology. We built the ceramic antenna system based on the HFSS design, and analyzed its performance by measuring the impedence matching and gains using Network Analyzer. We attach the developed prototype to UHF RFID portable terminal, and performed distance measuring for five widely used types of RFID tags to verify the performance of our proposed antenna system.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.10 no.3
• /
• pp.119-125
• /
• 2014

Echo cancellation is required for a dual-duplex high speed communication such as digital subscriber line(DSL), in order to allow each individual loop to operate in a full duplex fashion. Echo cancellation was one of the most difficult aspects of DSL design, requiring high linearity and total echo return loss in excess of 70 dB. For a long and rapidly changing echo response, if the echo is cancelled by an adaptive echo canceller, the echo canceller needs more taps and its performance is decreased. But if the response is divided into several responses, which response is estimated by a adaptive digital filter and combined, the computation complexities are decreased and the performance is increased. Therefore, the adaptive multi-stage echo canceller is proposed to decrease the computation complexity and increase the performance of echo return loss, in which the echo canceller is composed of several stage echo canceller estimating each divided echo response. Through computer simulations, this multi-stage echo canceller is verified to have merits for high speed communications such as DSL application.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.10
• /
• pp.1731-1736
• /
• 2008

In this paper, singly fed circularly polarized nearly-square patch antenna for receiving S-DMB is presented. It used teflon substrate of relative dielectric constant ${\in}_{\gamma}=2.2$ and the sire is $40{\times}40{\times}15[mm]$. Experimental results of fabricated antenna show that input return loss and axial ratio are about 22MHz, 25MHz at the center resonant frequency, respectively. And fabricated LNA has gain of 27.5 [dB], NF of 1.27 [dB], input return loss of -15.4 [dB] and output return loss of -18.9 dB, respectively. Simulation results and experimental results are good agreements. This proposed antenna is well able to handheld gadgets for receiving S-DMB.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.525-529
• /
• 2009

In this paper, microstrip patch antenna with diagonal slotted type using RFID is designed. This microstrip patch antenna is designed by considering the properties of critical parameter like the size, the truncating dimension, position of feed power and the height of airspace. the designed microstrip patch antenna has the lowest return loss in 915MHz, and in case of the voltage standing wave ratio(VSWR) is less than 1.2 under return loss -16dB, it has bandwidth of about 26MHz. Also, the microstrip patch antenna has the gain of 6dBi on the center frequency of 915MHz band and 2.8dB in the rate of reduction.