• 한국축산식품학회지
• /
• 제18권2호
• /
• pp.176-184
• /
• 1998

The objective of this study was to investigate the effects of freezing rate on aroma retention and to examine the mechanism of aroma retention during freeze drying process. Our experiments were carried out with self-manufactured freeze-dryer. Gelatin gels (2% w / w, 80${\times}$20mm) containing diacetyl(2mg/ml) were frozen unidirectionally (Neumann's model) from the bottom at -45, -30, -20, and -15$^{\circ}C$ and followed with freeze-drying. Under the upper conditions we measured freezing rate and the change of temperature and pressure during freeze drying. Freeze-dried gelatins were cut horizontally into 5 mm thickness from the bottom measured and diacetly contents. Besides, we observed the effect of the relative humidity of the diacetyl contents freeze-dried gelatin during storage. The retained diacetyl content was increased at high freezing temperature and in order of 0∼5, 5∼10, 10∼15, 15∼20 mm section from the bottom of the sample. It was observed that the retained diacetyl content was high in 15∼20 mm section. The retained diacetyl content and freeze-dried gelatin stored in the condition of high relative humidity was decreased significantly but in the low relative humidity case, was it decreased in small amount. The results of our experiment resents that the low temperature freezing and low humidity storing condition is effective for preserving aroma compound in food.

• Journal of the Korean Wood Science and Technology
• /
• 제52권2호
• /
• pp.157-174
• /
• 2024

This study investigates the influence of varying concentrations of boric acid (BA) preservative on the physical and mechanical properties of light red meranti (LRM) found in Sarawak. LRM or Shorea leprosula samples were treated with various concentrations of BA via the dip diffusion method using American Society for Testing and Materials (ASTM) standards. The physical property, particularly the retention rate and mechanical properties, bending strength, modulus of elasticity (MOE), tensile and compression strength parallel to grain of impregnated and control samples were tested to determine the effects of BA preservative. The retention rate was found to increase with increasing BA concentration and higher surface area to volume ratio. The mechanical properties in terms of the MOE and tensile strength parallel to grain were found to be greater than those of the control samples, whereas the bending strength and tensile strength parallel to grain were lower. Amongst the results, only the retention rate and MOE showed significant interaction effects at 5% level of significance between all factors tested (samples size and BA concentration for retention rate and BA concentration for MOE).

• 한국물환경학회지
• /
• 제25권1호
• /
• pp.159-166
• /
• 2009

This study has been attempted to generate electricity, while simultaneously treating artificial organic wastewater using both batch and continuous microbial fuel cells (MFCs). In the batch MFC, current-voltage curve showed an onset potential of -0.69 V vs. Ag/AgCl. The potential range between this potential and 0 potential displayed an available voltage for an automatic production of electric energy and glucose, which was oxidized and treated at the same time. The 486 mg/L glucose solution showed the maximum power of $30mW/m^2$ and the maximum current density of $75mA/m^2$ shown in the power curve. As a result, discharging of the cell containing COD 423 mg/L at the constant current density of $60mA/m^2$ showed a continuous electricity generation for about 22 hours that dropped rapidly due to dissipating of organic material. Total electric energy production was 18.0 Wh. While discharging, the pH change was low and dropped from pH 6.53 to 6.20 then increased to 6.47, then stabilized at this charge. The COD treatment efficiency was found to be 72%. In the continuous MFC, COD removal tends to increase as the hydraulic retention time is increased. At one day of hydraulic retention time as the maximum value reaches the COD removal efficiency, power production rate and power production rate per COD removal that were obtained were 68.8%, $14mW/m^2$, and $20.8mW/m^2/g$ CODrm, respectively. In the continuous MFC, the power production rate per COD removal increases as the hydraulic retention time is increased and decreases as the organic loading rate is increased. At the values lower than an organic loading rate of $1kgCOD/m^3/d$, the values higher than about $18.1mW/m^2/g$ CODrm could be obtained.

• Journal of Korean Society for Atmospheric Environment
• /
• 제24권E1호
• /
• pp.12-23
• /
• 2008

Relationship between the optimum soil water content and clay content on soil samples from mid-latitude European forest was tested. Soil samples from 4 different experimental sites (two forest sites in the Netherlands and a Danish forest) were collected, and analyzed for the soil physical and chemical characteristics. Water retention curves for the soil samples were determined according to the standard procedure ISO 11274, and pF decreased with increase in soil water contents. NO is simultaneously produced and consumed by microbiological processes, which comprise of nitrification and denitrification. NO consumption and production rates were determined from the soil samples and compared to their corresponding water retention curves in order to find the optimum soil water content and matric potential for maximum NO release from mid-latitude soils. NO consumption rate coefficient (k) in Hollandse Hout was significantly lower than those in other soil sites. Maximum NO production was observed at an intermediate soil moisture ($0.2{\sim}0.3kg/kg$) in all the soil samples. Resulting from the NO consumption and production rates for the soils, the empirical NO fluxes of the different soils were calculated in the laboratory.

• 한국환경보건학회지
• /
• 제26권4호
• /
• pp.15-20
• /
• 2000

The studies of swine wastewater treatment aim to development of process using soil microorganism. Removal rate of swine wastewater containing organic matter was 99 percent in case of high loading rate. Microorganism was devoted to improve the treatment efficiency of the process. According to the result obtained from biological treatment of high loading rate swine wastewater. Hydraulic retention time was 2.3 days in unit process of biological phosphorus removal. BO $D_{rm}$ / $P_{rm}$ ratio was 1122 in room temperature anaerobic process and 355.6 in mesophilic anaerobic process. And then phosphorus removal rate mesophilic anaerobic process was 3 time as much as than room temperature acaerobic process.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2003년도 춘계학술발표논문집
• /
• pp.80-92
• /
• 2003

The water retention of coating colors can be accurately measured by devices such as an AA-GWR water retention meter whose principle of measurement is based on pressure filtration of coatings under an externally applied air pressure over a certain period of time. It was hypothesized that such devices could be also used to determine the immobilization solids(IMS) of coating colors by determining a sudden drop in the rate of dewatering, that is, a sudden change in the drainage curves. To test this hypothesis, the immobilization solids of coating colors containing various thickeners and water retention additives at different levels were first accurately measured by a modified immobilization tester based on the well-known gloss drop method, and then their values were compared with those obtained by an AA-GWR water retention tester. They agreed very well and showed that the mean of the solids differences is 0.36% in the IMS points between both methods. This good agreement was not surprising because both test methods are based on the same end-point, that is, the immobilization solids point at which menisci begin to form at the coating surface. Theoretical considerations supporting this new method for measuring the immobilization solids of coating colors are presented and some recommendations for the test method are discussed. Also, the effect of various thickeners and water retention additives on the properties and printability of coated papers is discussed.

• 한국환경복원기술학회지
• /
• 제6권6호
• /
• pp.49-55
• /
• 2003

Total phosphorous removal rate was examined of a subsurface-flow treatment wetland system which was constructed on floodplain in the down reach of the Kwangju Stream in Korea from May to June 2001. Its dimensions were 29 meter in length, 9 meter in width and 0.65 meter in depth. A bottom layer of 45 cm in depth was filled with crushed granite with about 15~30 mm in diameter and a middle layer of 10 cm in depth had pea pebbles with about 10 mm in diameter. An upper layer of 5 cm in depth contained course sand. Reeds(Phragmites australis) were transplanted on the surface of the system. They were dug out of natural wetlands and stems were cut at about 40 cm height from their bottom ends. Water of the Kwangju Stream flowed from a submerged dam into it via a pipe by gravity flow and treated effluent was funneled back into the Stream. The number of reed stems increased from 80 stems/$m^2$ in July 2001 to 136 stems/$m^2$ in September 2001. The hight of stems was 44.2 cm in July 2001 and 75.3 cm in September 2001. The establishment of reeds at early operating stage of the system was good. Volume and water quality of inflow and outflow were investigated from July 2001 through December 2001. The average inflow was 40 $m^3$/day and hydraulic detention time was about 1.5 days. The concentration of total phosphorous n influent and effluent was 0.83 and 0.33 mg/L, respectively. The removal rate of total phosphorous averaged about 60%. The removal efficiency was slightly higher, compared with that of subsurface-flow wetlands operating in North America, whose retention rate of total phosphorous was reported to be about 56%. The good abatement rate could be attributed to sedimentation of particle phosphorous in pores of the media and adsorption of phosphorous to the biofilm developed on the surface of them. Increase of standing density of reeds within a few years will develop root zones which may lead to increment in the phosphorous retention rate.

• 직업교육연구
• /
• 제35권6호
• /
• pp.39-63
• /
• 2016

이 연구의 목적은 실업자가 훈련프로그램을 수료한 이후에 실업자의 실제적인 취업률과 고용유지율에 영향을 미치는 변인을 구명하는 데 있었다. 이를 위해 2012년 훈련서비스 품질 등에 관한 설문조사에 응답한 국가기간 전략산업직종(이하 '기간전략') 훈련생(889명) 중에서 최종적으로 수료한 훈련생(840명)의 훈련과정 종료 후 2년 이상의 고용보험 가입여부 및 가입기간 등에 관한 자료를 활용하여 생존분석(생명표 분석, Cox 회귀모형 분석)을 실시하였다. 이 연구의 주요 결과는 첫째, 수료 후 취업률이 가장 높은(36.8%) 시기는 3개월 이내이고, 전체 훈련생의 50% 이상이 취업한 시기는 6개월 이내로 나타났다. 수료 후 1년과 2년이 경과된 시점까지도 지속적으로 취업이 발생하고 있지만, 시간이 지날수록 취업률은 점점 감소하는 것으로 나타났다. 둘째, 수료 후 취업률에 영향을 미치는 변인은 훈련서비스 품질 중 교수역량(-)과 고용가능성(+)으로, 교수역량을 낮게 인식할수록, 자신의 고용가능성을 높게 인식할수록 취업확률이 높게 나타났다. 셋째, 취업 후 고용상실률이 가장 높은(각 22.0%, 22.3%) 시기는 3개월 이내와 3~6개월 이내이고, 전체 훈련생의 50% 이상이 고용보험을 상실한 시기는 8.8개월 이내로 나타났다. 넷째, 취업 후 고용유지율에 영향을 미치는 변인은 훈련서비스 품질 중 교사-학생관계(+), 학우관계(+), 훈련만족도(+)로, 교사-학생관계와 학우관계의 품질을 높게 인식할수록, 훈련만족도를 높게 인식할수록 취업 후 고용유지확률이 높게 나타났다.

• Membrane and Water Treatment
• /
• 제9권5호
• /
• pp.343-351
• /
• 2018

As membrane fouling is based on various factors, it is a complex phenomenon that is hard to estimate. This study investigated membrane fouling in a thermophilic jet loop membrane bioreactor (JLMBR). With this purpose, four different empirical membrane fouling models with different sludge retention times were applied on the flow data obtained in the system. As a result of the model implementation, it was found for all sludge retention times that, standard blocking is effective in the first 1.5 hours of filtration, while cake filtration was dominant in the remaining duration. Additionally, it was observed that as the sludge retention time increases, membrane fouling rate decreases.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1991년도 추계학술대회 논문집
• /
• pp.44-47
• /
• 1991

Electron injection and memory retention chracteristics of the MNOS devices with thin oxide layer of 23${\AA}$ thick and silicon nitride layer of 1000${\AA}$ thick which are fabricated for this experiment. As a result, pulse amplitude increase oxide current is dominated in linearly increasing region of $\Delta$V$\_$FB/the decreasing region after saturation was due to the increased silicon nirtide current. In low pulse ampiltude $\Delta$V$\_$FB/ is not variated on temperature, but as temperature and pulse amplitude increase. $\Delta$V$\_$FB/ is decreased after saturation. And the decay rate during 10$^4$sec after electron injection was ohiefly dominated by the back tunneling of emission from memory trap to silicon. Memory retention characteristics in V$\_$FB/ stage was better than that of OV retention regardless of injection conditions.