• Journal of the Korean Geotechnical Society
• /
• v.24 no.6
• /
• pp.69-75
• /
• 2008

Shear tests were carried out on interface between two concrete eco-blocks which comprise segmental retaining wall. Three interface conditions were considered : 1) direct contact of two blocks, 2) placing rubber pad between two blocks, 3) placing rubber pad and shear key between two blocks. According to shear tests, shear load-shear displacement relationship which was obtained from direct contact of two blocks was similar to elastic-perfectly plastic behavior. Ductile behavior of shear load-shear displacement relationship was observed for the interface condition of placing rubber pad. Apparent minimum shear capacities and apparent friction angles for the interface conditions of direct contact of two blocks, placing rubber pad between two blocks, placing rubber pad and shear key were 1.7 kN/m, $27.6^{\circ}$ and 4.2 kN/m, $26.2^{\circ}$ and 20.9 kN/m, $26.0^{\circ}$ respectively.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.6
• /
• pp.101-116
• /
• 2008

The use of reinforced earth walls id permanent structures is getting its popularity. Despite a number of advantages of reinforced earth walls over conventional concrete retaining walls, there exists concerns over long-term residual deformations when subjected to repeated and/or cyclic loads, during their service period. In this investigation, the effects of pre-loading in reducing long term residual deformation of reinforced soil structures under sustained and/or repeated loading environment are investigated using a series of reduced-scale model tests. A model pier and a back-to-back (BTB) reinforced soil structures were constructed and tested under various loading and backfilling conditions. The results indicate that the pre-loading technique can be an effective means of controlling residual deformations of reinforced soils under various loading conditions.

• Journal of the Korean GEO-environmental Society
• /
• v.25 no.6
• /
• pp.13-17
• /
• 2024

The general soil nailing method, which is currently used domestically and internationally to stabilize the slopes of sandy slopes, is to form a kind of gravity-type retaining wall by drilling the ground and grouting it with a single steel bar. This method can reduce construction costs, ease of construction, relative strength and displacement, and is highly efficient. The difference between grouting and rebar adhesion to the yield pullout force and the difference between the amount of deformation in relation to the same pullout resistance was analyzed through field tests to identify engineering excellence, and in terms of construction cost, the reduction effect was evaluated by analyzing the difference in the number of drillings and the impact on the overall construction cost, such as material cost, when the same strength constant is applied to the ground with the same resistance.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.44 no.3
• /
• pp.1-12
• /
• 2016

This study aimed to interpret the fundamental cause of road-kill occurrences and analyzed spatial characteristics of the road-kill locations from Route 44 in Seorak National Park, Korea. Logistic regression analysis was utilized for backward elimination on variables. Seorak National Park Service has constructed GIS-data of 81 road-kill occurrences from 2008 to 2013 and these data were assigned as dependent variables in this study. Considered as independent variables from previous studies and field surveys, vegetation age-class, distance to streams, coverage of fences and retaining walls, and distance to building sites were assigned as road-kill impact factors. The coverage of fences and retaining walls(-1.0135) was shown as the most influential factor whereas vegetation age-class(0.0001) was the least influential among all of the significant factor estimates. Accordingly, the rate of road-kill occurrence can increase as the distance to building sites and stream becomes closer and vegetation age-class becomes higher. The predictive accuracy of road-kill occurrence was shown to be 72.2% as a result of analysis, assuming as partial causes of road-kill occurrences reflecting spatial characteristics. This study can be regarded as beneficial to provide objective basis for spatial decision making including road-kill occurrence mitigation policies and plans in the future.

• Journal of the Korean Geosynthetics Society
• /
• v.14 no.3
• /
• pp.1-12
• /
• 2015

During installing sheet piles for an impermeable wall or a retaining wall, vibratory hammers are widely used. Among vibratory hammers, a hydraulic hammer is used most commonly. However, a hydraulic hammer causes excessive vibration and noise due to resonance by change of natural frequency according to movements of eccentric shaft when the hammer starts and stops. In this study, new variable amplitude type hammer is developed in order to reduce the vibration and noise due to resonance produced in starting and stopping the hammer. By controlling horizontal angle in two pairs of eccentric body inside of the hammer, the amplitude and vibration of the new hammer can be controlled. The performance tests with the new hammer and existing hammers such as the hydraulic hammer and electric hammer are carried out, and the new hammer shows reduced vibration and noise results in comparison with existing hammers from performance tests. Also, this study shows that penetration rates of sheet pile using the new hammer increase due to impellent force of a backhoe in comparison with the electric hammer and penetration rate increase in comparison with a general hydraulic hammer, since the new hammer can control the amplitude during penetration of sheet pile according to soil condition.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.3 no.2
• /
• pp.127-135
• /
• 1983

A new approach is developed to analyze the reliability of the earth retaining wall using the concept of probability of failure, instead of conventional factor of safety. Many uncertainties, which are included in the conventional stability analysis, can be excluded by using the stochastic approach. And the reliability, more consistent with the reality, can be obtained by the simulation. The strength parameters of soil properties are assumed to be random variables to follow a generalized beta distribution. The interval [A, B] of the random variables could be determined using the maximum likelihood estimation. The pseudo-random values corresponding to the proposed beta distribution are generated using the rejection method. The probability of failure defined as follows, is obtained by using the Monte Carlo Method. $$P_f=\frac{M}{N}$$ where, $P_f$ : Probability of failure N : Total number of trials M : Total number of failure out of N A computer program is developed for the computation procedure mentioned above. Finally, a numerical example is solved using the developed program.

• Journal of the Korean Geosynthetics Society
• /
• v.19 no.3
• /
• pp.9-21
• /
• 2020

In this study, the design method of the combined sheet pile was considered in the coastal landfill where sandy and clayey soils are mixed, and the behavior in excavation was analyzed. It was confirmed from the elasto-plastic analysis that the predicted behavior of the temporary facilities of earth retaining differs according to the type of the combined sheet pile method (Built up, Interlocking, Welding) and the analysis method (soldier pile method, continuous wall method). In the case of sheet pile member force, the results of the continuous wall analysis method predicted the most conservative results. When the stress ratio (calculation/allowance) of each member was analyzed based on the maximum member force of the combined sheet pile method, the maximum value was obtained for bending moment in the side pile and combined stress in the case of the strut. As a result of finite element analysis, the member force of the side pile was the largest in the short-term effective stress analysis condition, while the compressive force of the strut was large in the consolidation analysis. When comparing the results of the elasto-plastic analysis and the finite element analysis, the shear force of the side pile and the axial force of the strut were greatly evaluated in the elasto-plastic analysis, and the bending moment of the side pile was the largest in the short-term effective stress condition of the finite element analysis. In addition, the displacement of the side pile was predicted to be greater in the finite element analysis than in the elasto-plastic analysis.

• Journal of the Korea Concrete Institute
• /
• v.21 no.3
• /
• pp.283-290
• /
• 2009

Differently from fly ash, the bottom ash produced from thermoelectric power plant has been treated as an industrial waste matter, and almost reclaimed a tract from the sea. If this waste material is applicable to foam concrete as an aggregate owing to its light-weight, however, it may be worthy of environmental preservation by recycling of waste material as well as reducing self-weight of high-rising structure and horizontal forces and deformations of retaining wall subject to soil pressure. This study has an objective of evaluating the effects of application of bottom ash on the mechanical properties of foam concrete. Thus, the ratio of bottom ash to cement was selected as a variable for experiment and the effect was measured in terms of unit weight of concrete, air content, water-cement ratio and compressive strength. It can be observed from experiments that the application ratios have different effects on the material parameters considered in this experiment, thus major relationships between application ratio and each material parameter were finally introduced. The result of this study can be applied to decide a mix design proportion of foam concrete while bottom ash is used as an aggregate of the concrete.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.2
• /
• pp.27-39
• /
• 2012

This research is to propose the reinforcing method and design code for the lateral behaviors of the abutment displacement induced from the rainfall infiltration on high landfill slope. First, to make the proper numerical analysis, in-situ soil (weathered granite soil) was taken, and the variance of strength parameters according to water content variance was examined by undrained direct shear test, furthermore, other soil parameters were calculated from the standard penetration test such as elastic modulus and Poisson's ratio etc,. Those parameters were used to calculate the lateral behavior of abutment by finite element method and the member force of pile in high landfill slope according to rainfall infiltration . From the results, the shoe displacement on abutment was calculated as 8.98cm, which is 3 times bigger than the allowable displacement, 3cm. To reinforce it, several reinforcing methods were selected and analyzed such as reinforced retaining wall, soil surcharge, pile reinforcing (5m enlargement, 3-line arrangement, 5m enlargement and 3-line arrangement). In case of 5m enlarged and 3-line arrangement piles, the lateral behavior of shoe showed lower value(2.26 cm) than allowable displacement.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.5
• /
• pp.37-46
• /
• 2014

Geotechnical structures have been analyzed and constructed in various geometry conditions to maintain their stability in accordance with the characteristics of construction design. Shear strengths are generally obtained from triaxial test to apply to design analysis. Geotechnical structures under strip loading, such as earth dam, embankment, and retaining wall, have the strain in a direction, and plane strain condition. Thus, an approximate shear strengths should be applied for stability analysis suitable to ground condition. When applying shear strengths obtained from triaxial tests for slope stability analysis, the evaluation of it may underestimate the factor of safety because the implementation is not suitable for geometry condition. The paper compares shear strengths obtained from triaxial test and plane strain test based on various relative densities using weathered granite soils. Additionally, yield stress is determined by maximum axial strain 15% in triaxial test because of continuous kinematic hardening, but plane strain test can determine a failure point in critical state to evaluate the shear strengths of soils at the second plastic hardening step. This study proposes to perform an appropriate test for many geotechnical problems with plane strain condition.