• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.129-131
• /
• 2007

In this paper, we research improvement in efficiency of single-phase induction motor by adapting the condition of the balanced and quasi-balanced operation. we maintain turns of auxiliary winding of the motor and adjust resistance and reactance. In this condition, resistance value and copper loss are much gloater. Namely, this is the condition only for balancing MMF without consideration of copper loss of stator winding. To make more practical design, therefore, we will perform winding design which is based on balanced operation condition and applies copper loss minimum. The problem of deterioration of starting torque is completed by rotor bar shape design.

• Journal of Electrical Engineering and Technology
• /
• 제8권5호
• /
• pp.1221-1226
• /
• 2013

In this paper, the equivalent circuit for the efficiency calculation by precise estimation of the linkage flux, inductance and iron loss resistance was calculated accurately. In addition, the driving characteristics according to the current phase angle are analyzed and the maximum efficiency point is calculated. And then, analyzed and experimental values of the efficiency were compared. So, causes of error were expected to be vibration and noise by harmonic distortion of the voltage and current, and mechanical loss of dynamometer. In addition, the driving characteristics according to the current phase angle are analyzed and the maximum efficiency point is calculated.

• 대한기계학회논문집B
• /
• 제25권1호
• /
• pp.1-8
• /
• 2001

Performance of a rectangular fin is investigated by a three dimensional analytical method. Heat loss and the temperature obtained from the three dimensional analysis are compared with those calculated from a two dimensional analysis. Fin effectiveness, fin resistance and fin efficiency for the rectangular fin are presented as a function of non-dimensional fin length and fin width. The results are obtained in the following : (1) heat loss calculated from the two dimensional analysis is the same as that obtained from the three dimensional analysis with adiabatic boundary condition in z-direction, (2) heat loss obtained from the two dimensional analysis approaches the value for the three dimensional analysis as the non-dimensional fin width becomes large, (3) fin effectiveness increases as non-dimensional fin length increases and non-dimensional fin width decreases, and vice versa for fin efficiency.

• 한국공작기계학회논문집
• /
• 제11권5호
• /
• pp.88-92
• /
• 2002

This research is about slurry wear of SM45C and SUS304, which using standard sand and KUM river sand. The results are as follows ; 1. Mass loss rates of both standard sand and KUM river sand were linearly increased as increasement of time and velocity. 2. The average diameter of sand from relatively, less wear rate and portion of larger particles. 3. Wear resistance was linear with time and velocity of liquid jet regardless of type of sand. Also, it was able to evaluate with the formula, $HV^2$/E calibrated with n, the velocity index. 4. The wear surface in liquid jet experiment was smooth. The maximum wear depth was observed at the location 2~4mm apart from the center in the condition of $90^{\circ}$ of collision angle 6mm of nozzle diameter, and 20mm of collision distance. The sectional shape in radial appeared as 'W'shape.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.798-801
• /
• 2001

This research is about slurry wear of SM45C and SUS304, which using standard sand and KUM river sand. The results are as follows ; 1. Mass loss rates of both standard sand and KUM river sand were linearly increased as increasement of time and velocity. 2. The average diameter of sand from relatively, less wear rate and portion of larger particles. 3. Wear resistance was linear with time and velocity of liquid jet regardless of type of sand. Also it was able to evaluate with the formula, HV2/E calibrated with n, the velocity index. 4. The wear surface in liquid jet experiment was smooth. The maximum wear depth was observed at the location, 2~4mm apart from the center in the condition of 90$^{\circ}$of collision angle 6mm of nozzle diameter, and 20mm of collision distance. The sectional shape in radial appeared as 'W' shape.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.683-684
• /
• 2008

The resistance is frequency dependent by the Seeback effect, loading effect, Eddy current loss, uniformly distributed inductance of the resistance element and uniformly distributed self-capacitance of the resistance element and capacitance between resistance element and it's box. A precise ac resistance measurement system has been developed for using as maintaining and dissemination of national ac resistance standards. The developed resistance measurement system can be used as a instrument of national ac resistance standards at frequency less than 10 kHz and it's measurement accuracy was 0.23(${\mu}{\Omega}/{\Omega}$)+4.2 ${\mu}{\Omega}$ at 1592 Hz and 20 V.

• 디지털융복합연구
• /
• 제3권1호
• /
• pp.9-25
• /
• 2005

The purpose of this study is to explore conquest plans of the barrier and resistance in innovation management. In addition, this study is to describe the model of innovation resistance that reflects adoption process stages and identify the factors that drive the resistance of consumers and the barriers. Whenever organizations try to plan and implement some kind of innovation in organizations, they confront the resistance and barriers in many ways. By understanding innovation resistance and barrier, organizations can not only design better innovations but can develop strategies to reduce resistance and conquer the barriers. Thus they accelerate innovation. Also, these results indicate that people resist innovation strongly when it betrays their value, needs and beliefs or when they felt the pressure on self-conviction and mental risk, loss, and lack of knowledge. Understanding the factors that drive the innovation resistance and barrier has important implications for both theoretical development and managerial action.

• 전기학회논문지P
• /
• 제54권1호
• /
• pp.15-19
• /
• 2005

This paper analyzed the power loss characteristics according to winding thickness and winding method of high frequency transformer. Power loss was analyzed by PExprt using FEM tool. The ferrite core model for analysis be used the EE10 type of TDK cop.. Transformer model objected flyback transformer type applied to flyback converter/inverter. Therefore, analysis results of loss were obtained from inner parameters of DC, AC resistance, leakage inductance, copper loss, core loss, and temperature etc.

• 한국재료학회지
• /
• 제27권10호
• /
• pp.518-523
• /
• 2017

In commercial solar cells, the pattern of the front electrode is critical to effectively assemble the photo generated current. The power loss in solar cells caused by the front electrode was categorized as four types. First, losses due to the metallic resistance of the electrode. Second, losses due to the contact resistance of the electrode and emitter. Third, losses due to the emitter resistance when current flows through the emitter. Fourth, losses due to the shading effect of the front metal electrode, which has a high reflectance. In this paper, optimizing the number of finger on a $4{\times}4$ solar cell is demonstrated with known theory. We compared the short circuit current density and fill factor to evaluate the power loss from the front metal contact calculation result. By experiment, the short circuit current density($J_{sc}$), taken in each pattern as 37.61, 37.53, and $37.38mA/cm^2$ decreased as the number of fingers increased. The fill factor(FF), measured in each pattern as 0.7745, 0.7782 and 0.7843 increased as number of fingers increased. The results suggested that the efficiency(Eff) was measured in each pattern as 17.51, 17.81, and 17.84 %. Throughout this study, the short-circuit current densities($J_{sc}$) and fill factor(FF) varied according to the number of fingers in the front metal pattern. The effects on the efficiency of the two factors were also investigated.

• 한국디지털정책학회:학술대회논문집
• /
• 한국디지털정책학회 2005년도 춘계학술대회
• /
• pp.13-28
• /
• 2005

The purpose of this study is to explore conquest plans of the barrier and resistance in innovation management. This paper focuses to understand the model of innovation that reflects adoption process stages and identify the factors that drive the resistance of consumers. Whenever organizations try to plan and implement some kind of innovation in organizations, they confront resistance in many ways. By understanding innovation resistance, organizations can not only design better innovations but can develop strategies to reduce resistance. Thus they accelerate innovation. Understanding the factors that drive the innovation resistance has important implications for both theoretical development and managerial action. These results indicate that people resist innovation strongly when it betrays their value, needs and beliefs or when they felt the pressure on self-conviction and mental risk, loss, and lack of knowledge.