• Journal of the Korean Ceramic Society
• /
• v.51 no.5
• /
• pp.459-465
• /
• 2014

In this study, Si-SiC composites were fabricated using a Si melt infiltration method using ${\beta}$-SiC/C composite powders synthesized by the carbothermal reduction of $SiO_2-C$ precursors made from a TEOS and a phenol resin. The purity of the synthesized SiC-C composite powders was higher than 99.9993 wt% and the average particle size varied from 4 to $6{\mu}m$ with increasing carbon contents of the $SiO_2-C$ precursors. It was found that the Si-SiC composites fabricated in this study consist of ${\beta}$-SiC and residual Si, without any trace of ${\alpha}$-SiC. The 3-point bending strengths of the fabricated Si-SiC composites were measured and found to be higher than 550 MPa, although the density of the fabricated Si-SiC composite was less than $2.9g/cm^3$. The bending strengths and the densities of the fabricated Si-SiC composites were found to decrease with increasing C/Si mole ratios in the SiC-C composite powders. The specific resistivities of the Si-SiC composites fabricated using the SiC-C composite powders were less than $0.018{\Omega}cm$. With increasing C content in the SiC-C composite powders used for the fabrication of Si-SiC composites, the specific resistivity of the Si-SiC composites was found to slightly increase from 0.0157 to $0.018{\Omega}cm$.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.4
• /
• pp.476-492
• /
• 2003

Purpose : The purpose of this study was to compare HEMA and TEGDMA as diluents for the composite resin. Material and methods : Eight kinds of experimental light curable composite resins were prepared and used. Concentrations of monomer and filler were same for all experimental composites, except, the diluent's ratios to the monomer. The ratio of diluents to Bis-GMA were 15%, 20%, 25%, and 30%, and two kinds of diluents were used, so total experimental groups were eight including one control group of 25% TEGDMA. Results : Depth of cure, flexural strength, shear bond strength to bovine enamel, shear bond strength to bovine dentin, water absorption and solubility of composites in water were measured. Sample size for each groups were 10. Arithmetic means were used as each groups representative values, and regression test for two diluents and low concentrations, Duncan's multiple range test, and Two-way ANOVA test were done for kinds of diluents and its concentrations at level of 0.05. Conclusion : Following results were obtained ; 1. There were not significant differences in effects of HEMA and TEGDMA to depth of cure, flexural strength of composites and shear bond strength to bovine enamel (p>0.05). 2. Increase of the concentrations of the diluents made the depth of cure (p<0.001) and flexural strength (p<0.05) a little higher. 3. Shear bond strength to dentin was higher on HEMA containing composites than TEGDMA containing composites (p<0.001). 4. Water absorption was higher on HEMA containing composites than TEGDMA containing composites (p<0.01).

• Composites Research
• /
• v.28 no.6
• /
• pp.389-394
• /
• 2015

The sound absorption coefficient and sound transmission loss of graphite intercalation compound (GIC) included epoxy composites were investigated. Epoxy resin was infused into the expanded GIC and the impedance tube method was employed to measure the sound absorption coefficient and sound transmission loss. Scanning electron microscopy photographs showed uniform distribution of the GIC in the epoxy matrix. The surface density of epoxy/GIC (20 wt%) composites decreased about 56% compared to that of pure epoxy. The sound absorption coefficient of composites increased about 3 times at the frequency range of 500~1000 Hz compared to the pure epoxy. The sound transmission loss of composites decreased with increasing the GIC content and it is attributed to the increase of pores in the composites.

• Composites Research
• /
• v.26 no.3
• /
• pp.182-188
• /
• 2013

The purpose of this study was to measure the volumetric polymerization shrinkage kinetics and stress of a silorane-based dental restorative composite and compare it with those of conventional methacrylate-based dental composites. Two methacrylate-based composites (Z250, Z350 flowable) and one silorane-based composite (P90) were investigated. The volumetric polymerization shrinkage of the composites during light curing was measured using a laboratory-made volume shrinkage measurement instrument based on the Archimedes' principle, and the polymerization stress was also determined with the strain gage method. The shrinkage of silorane-based composites (P90) was the lowest, and that of Z350 flowable was the highest. Peak polymerization shrinkage rate was the lowest in P90 and the highest in Z350 flowable. The time to reach peak shrinkage rate of P90 was longer than those of the methacrylate-based composites. The polymerization shrinkage stress of P90 was lower than those of the methacrylate-based composites.

• Elastomers and Composites
• /
• v.47 no.2
• /
• pp.121-128
• /
• 2012

Waste EPDM(W-EPDM) collected from the automotive weather strip and the gasket of a laundry machine has not been effectively recycled. Using this W-EPDM powder and other ingredients, i.e., binder(polyolefin resin, polyolefin elastomer, etc.), filler and additives, various economic rubber composites were made by extrusion. In advance of main experiments, the effects of ultrasonic treatment of W-EPDM on the property of rubber composites, comparison in the property of the composites of W-EPDM with those of virgin and devulcanized EPDM, and waste tire rubber were investigated. Also, the properties of the rubber composites extruded with a 12-screw extruder were compared with those extruded with twin-screw extruder. Various W-EPDM composites for synthetic turf filler and car mat were extruded and injection molded, and 3 main properties of tensile strength, elongation and hardness were investigated to develop economical and proper recipes of the rubber composites.

• Restorative Dentistry and Endodontics
• /
• v.26 no.1
• /
• pp.23-31
• /
• 2001

The purpose of this study was to search the optimal silane concentrations for filler- silanization of seven experimental composites. Silica filer was a 25micron crushed type. 0.0%, 0.5%, 1.0%, 1.5%, 2.0%, 2.5%, and 3.0% silane($\gamma$-methacrylooxypropyltrimethoxysilane)were added into silica-filler with weight percentage (wt%). Mixtures(silica filler/silane)were reacted at 6$0^{\circ}C$ for 72hours, and crushed into fine particles those were used as fillers for 7 experimental composites. Monomer was a 3 : 1 mixture of Bis-GMA and TEGDMA containing 0.2% tertiary amine and 0.4% camphoroquinone for light curability. A ratio for mixing the monomer and filler was 75% and 25% respectively. Seven experimental composites was classified with the concentration of silane treated, and the specimen number for each test was 10. Specimens with 6mm diameter and 3mm height dimension for measuring the diametral tensile strength were destroyed with 1mm/min cross-head speed on Instron universal testing machine (No. 4467, USA). Shear bond strength was measured on the specimens bonded to bovine enamel etched with 37% phosphoric acid solution for 1 minute Fractured surfaces were observed by SEM (Hitachi S-3200, Japan) among that of the highest values measured from each groups. Following results were obtained: 1. Experimental composites containing silanized filter showed the significantly higher diametral tensile strength and shear bond strength than the composites containing un-silanized fillers(Group1) (p<0.05). 2. In silanized filler composite resins(Group 2~7), Diametral tensile strength of Group 3 showed the significantly higher than that of Group 2 and Group 6(p<0.05). 3. Shear bond strength was higher in Group 3 than that of Group 7 (p＜0.05)in silanized fillers composite resins. 4. Fracture surface was formed in resin matrixes on the specimens from composites containing the fillers treated with 0.5% 1.0%, and 1.5% silane. These results mean that the optimal silane concentrations are exist for each fillet with its size and surface area, and that 1.0% is a optimal value for concentration to coat the 25$\mu\textrm{m}$ filler with silane.

• Composites Research
• /
• v.31 no.6
• /
• pp.398-403
• /
• 2018

Recently, environmental pollution caused by plastic waste, ecosystem disturbance of micro-plastics and human body accumulation are becoming big problems. In order to replace the traditional plastic, eco-friendly resin and natural fiber-based composite materials have been developed, but they have a disadvantage that their mechanical properties are significantly lower than those of synthetic fiber-based composites. In this study, eco - friendly nanofiber was extracted from seaweed and used as an additive in order to improve the mechanical properties of jute fiber-reinforced composites. Through the hand lay-up process, the composites were fabricated, and it was confirmed that the nanofiber was effective in improving the mechanical properties of natural fiber composites through tensile, bending and drop weight impact tests.

• Journal of Technologic Dentistry
• /
• v.38 no.3
• /
• pp.135-142
• /
• 2016

Purpose: The aim of this research was to evaluate the influence of different surface treatments on the shear bond strength of zirconia ceramic to composite resin. Methods: Seventy two cylinder-shape (diameter: 5 mm; height: 12 mm) blocks of experimental industrially manufactured Y-TZP ceramic were abraded with $125{\mu}m\;Al_2O_3$ particles and randomly divided into 4 groups. All the materials were categorized as group Gc(control group - composite resin veneering on zirconia surface), Gr - composite resin veneering after surface treatment of Rocatec system (3M ESPE, Seefeld, Germany) group; Gz - composite resin veneering after surface treatment of Zirconia primer (Z-primer, Bisco, U.S.A) group; Gm - composite resin veneering after surface treatment of zirconia primer (Monobond plus, ivoclar vivadent AG, Liechtenstein) group. Two different zirconia primers and Rocatec system were used to zirconia cylinders (n=16) onto the zirconia surface. Zirconia specimens, polished and roughened, were pretreated and composite bilayer cylinders bonded using conventional adhesive techniques. Results: Shear bond strengths were analyzed using single-factor ANOVA(p<0.05). Bond strength values achieved after airbone particle abrasion and zirconia surface pre-treatments(p<0.05). Conclusion: Shear bond strength tests denmonstrated that zirconia primer is a viable method to improved bond strength between zirconia ceramic core and veneering composites.

• Restorative Dentistry and Endodontics
• /
• v.40 no.4
• /
• pp.270-275
• /
• 2015

Objectives: This study examined the color changes of a resin composite with different shades upon exposure to water with different pH. Materials and Methods: Nanohybrid resin composites (Filtek Z350XT, 3M ESPE) with four different shades (A2, A3, B1, and B2) were immersed in water with three different pH (pH 3, 6, and 9) for 14 day. The CIE $L^*a^*b^*$ color coordinates of the specimens were evaluated before and after immersion in the solutions. The color difference (${\Delta}E^*$) and the translucency parameter (TP) were calculated using the color coordinates. Results: ${\Delta}E^*$ ranged from 0.33 to 1.58, and the values were affected significantly by the pH. The specimens immersed in a pH 6 solution showed the highest ${\Delta}E^*$ values (0.87 - 1.58). The specimens with a B1 shade showed the lowest ${\Delta}E^*$ change compared to the other shades. TP ranged from 7.01 to 9.46 depending on the pH and resin shade. The TP difference between before and after immersion in the pH solutions was less than 1.0. Conclusions: The resulting change of color of the tested specimens did not appear to be clinically problematic because the color difference was < 1.6 in the acidic, neutral, and alkaline solutions regardless of the resin shade, i.e., the color change was imperceptible.

• Composites Research
• /
• v.12 no.2
• /
• pp.70-81
• /
• 1999

Resin transfer molding(RTM) as a composite manufacturing process is currently of great interest in the aerospace industry requiring high performance composite parts. In this study, an analysis of mold filling in the RTM process was carried out by numerical simulation using finite element/control volume technique. Experimental work for the visualization of resin flow through fibrous preform was also conducted in order to quantitatively measure the permeabilities of the fiber mats and to evaluate the validity of the developed numerical code. The different types of fiber mats and silicon oils were selected as reinforcements and resin materials, respectively. The effects of fibrous preform structure, mold geometry, and preplaced insert on the flow front patterns during mold filling were examined by integrating the model predictions and experimental results. The flow fronts predicted by numerical simulation were in good agreement with those observed experimentally. However, according to the regions of the mold, some deviations between predicted and observed flow fronts could be found because of non-uniform fiber volume fraction. Weldline locations for the resin flow through round insert preplaced in the mold could be qualitatively deduced based on predicted flow fronts.