• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.58 no.2
• /
• pp.159-174
• /
• 2022

Flow prediction was carried out through observational survey and three dimensional multi-layered numerical diagnostic model experiment to clarify the time and spatial structure of tidal current and residual flow dominant in the sea exchange and material circulation of the waters around Geumo Islands in the southern waters of Korea. The horizontal variation of tidal current is so large that it causes asymmetric tidal mixing due to horizontal eddies and the topographical effect creating convergence and dispersion of flow direction and velocity. Due to strong tidal currents flowing northwest-southeast, counterclockwise and clockwise eddies are formed on the left and right sides of the south of Sori Island. These topographical eddies are created by horizontal turbulence and bottom friction causing nonlinear effects. Baroclinic density flows are less than 5 cm/s at coastal area in summer and the entire sea area in winter. The wind driven currents assuming summer and winter seasonal winds are also less than 5 cm/s and the current flow rate is high in winter. Density current in summer and wind driven current in winter have a relatively greater effect on the net residual flows (tidal residual current + density current + density driven current) around Geumo Islands Sea area.

• Journal of Welding and Joining
• /
• v.11 no.3
• /
• pp.34-47
• /
• 1993

Finite element models were developed for thermal and residual stress analysis for the specific welding problems. They were used to evaluate the effectiveness of the various welding heat input models, such as ramp heat input function and lumped pass models. Through the parametric studies, thermal-mechanical modeling sensitivity to the ramp function and lumping techniques was determined by comparing the predicted results with experimental data. The kinetics for residual stress formation during welding can be developed by iteration of various proposed mechanisms in the parametric study. A ramp heat input function was developed to gradually apply the heat flux with variable amplitude to the model. This model was used to avoid numerical convergence problems due to an instantaneous increase in temperature near the fusion zone. Additionally, it enables the model to include the effect of a moving arc in a two-dimensional plane. The ramp function takes into account the variation in the out of plane energy flow in a 2-D model as the arc approaches, travels across, and departs from each plane under investigation. A lumped pass model was developed to reduce the computation cost in the analysis of multipass welds. Several weld passes were assumed as one lumped pass in this model. Recommendations were provided about ramp lumping techniques and the optimum number of weld passes that can be combined into a single thermal input.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.1
• /
• pp.39-47
• /
• 2020

In order to investigate current characteristics at the Gungpyung beach, which is a macrotidal flat, field measurements were carried out in the summer and winter at the intertidal and the subtidal zones. The distribution of residual current at intertidal flat was dominant in the northward direction in the summer and dominant in the northward and southwestern directions in the winter. The direction and speed of the residual current in the winter are highly correlated with the significant wave height, and the turbidity is also highly correlated with the significant wave height. Therefore, in the winter, high sediment rates are suspended by high waves, and sediments are transporting due to the residual current in the southwest direction. On the other hand, it is expected that the northward residual current is predominant due to the small wave in the summer, and sediment transport does not occur largely due to less suspended sediments. In addition, sediment transport in the southern direction is blocked by the dock, which is the artificial structure, and the erosion occurs in the south side of the dock. The erosion pattern in the macrotidal zone of Yellow sea is dominated by seasonal waves, and blocking of sediments by artificial structure is very important.

• Advances in Computational Design
• /
• v.4 no.1
• /
• pp.43-52
• /
• 2019

Variation Analysis (VA) is used to simulate final product variation, taking into consideration part manufacturing and assembly variations. In VA, all the manufacturing and assembly processes are defined at the product design stage. Process Capability Data Bases (PCDB) provide information about measured variation from previous products and processes and allow the designer to apply this to the new product. A new challenge to this traditional approach is posed by the Industry 4.0 (I4.0) revolution, where Smart Manufacturing (SM) is applied. The manufacturing intelligence and adaptability characteristics of SM make present PCDBs obsolete. Current tolerance analysis methods, which are made for discrete assembly products, are also challenged. This paper discusses the differences expected in future factories relevant to VA, and the approaches required to meet this challenge. Current processes are mapped using I4.0 philosophy and gaps are analysed for potential approaches for tolerance analysis tools. Matching points of simulation capability and I4.0 intents are identified as opportunities. Applying conditional variations, incorporating levels of adjustability, and the un-suitability of present Monte Carlo simulation due to changed mass production characteristics, are considered as major challenges. Opportunities including predicting residual stresses in the final product and linking them to product deterioration, calculating non-dimensional performances and extending simulations for process manufactured products, such as drugs, food products etc. are additional winning aspects for next generation VA tools.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.245-249
• /
• 2009

According to the increase of intelligent vehicles many automotive electric components are installed. The wire harness which connects those also increases. The crimping process for compressing the copper wire bundle into the terminal is a key process to assure the good quality of wire harness. For the case of inadequate forming condition many shape failures such as less-filling, over-filling are happen in the crimping process. Even though the quality of crimping shape is satisfactory the quality check for electrical resistance of wire harness is sometime not satisfied the qualification due to large variation of electrical resistance of wire harness under climate test. This large variation is thought to be related with the malfunction automotive electric system and caused by the internal stress of wire, which occurred during the crimping process. In this paper we develop the 3D-FEM simulation scheme and design methodology of optimum terminal shape. Also the effect of terminal shape on the residual stress is discussed.

• Journal of Environmental Science International
• /
• v.22 no.9
• /
• pp.1105-1113
• /
• 2013

This paper attempted to estimate the emissions of HFC-134a from scrap truck as a result of measuring the residual quantities of HFC-134a in air conditioner of scrap truck. We measured the residual amounts in the scrap truck of 138 by applying commercial recover for refrigerants. The average residual rate(disposal-phase emission factor) is reported to be $44.3{\pm}3.3%$ within a confidence interval of 95%. Recent year model trucks exhibit the higher residual rates. Little variation, however, is observed in regard to vehicle size. The HFC-134a emission quantity from scrap truck in 2011 is estimated to be 55,908 $tCO_2$-eq that demonstrates 21.4% increase to compare with that in 2007. As the numbers of truck have increased dramatically during the last two decades, the emissions of HFC-134a from scrap truck would increase sharply in the next coming years. HFC-134a is a very high GWP greenhouse gas. therefore have to reduce the emissions from the scrap truck and need to find ways to recycle. The chemical compositions of refrigerants from scrap truck are quite similar to those of new refrigerants, suggesting that the refrigerants from scrap truck could be reused as refrigerant.

• Korean Journal of Veterinary Research
• /
• v.44 no.1
• /
• pp.23-28
• /
• 2004

We established a new method to analyze moxidectin using high performance liquid chromatography(HPLC) with fluorescence derivatization in order to obtain its residual profiles in biological samples. Recovery of moxidectin in tissue was 62% at 10 ppb. Average detection reproducibility in terms of coefficience variation was 4.47% at 0.32 to 10 ppb. Residual of moxidectin was studied in 44 Yorkshire-Landrace mixed bred male pigs administered subcutaneously 0, 200, or $800{\mu}g/kg$ body weight (BW) Residual profiles of moxdectin in blood, muscle, liver, kidney and fat of pigs were described. The concentration of the moxidectin in liver after administration of moxidectin was the highest among the tissues examined. Moxidectin in liver after administration of moxidectin as $200{\mu}g/kg$ BW was declined from $10.0{\pm}3.7ng/g$ at 10 day post administration to $0.5{\pm}0.3ng/g$ level at 40 day post administration. Residual levels of moxidectin in all samples were estimated to fall below the limit of quantitation (0.32 ng/ml) after 50 day after treatment of $200{\mu}g/kg$. Moxidectin showed no abnormal observations in all the clinical findings at any concentrations under these experimental conditions. In conclusion, this analysis method by HPLC after fluorescence derivatization was very effective for the detection of moxidectin in biological samples. We suggest that 50-day is safe enough for the withdrawal time of moxidectin in pigs, following the recommendation dose by the manufacturer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.135-135
• /
• 1999

It is well known that Raman spectroscopy is powerful tool in analysis of sp3/sp3 bonding fraction in diamond-like carbon(DLC) films. Raman spectra of DLC film is composed of D-peak centered at 1350cm-1 and G-peak centered at 1530cm-1. The sp3/sp3 fraction is qualitatively acquired by deconvolution method. However, in case of DLC film, it is generally observed that G-peak position shifts toward low wavenumber as th sp3 fraction increases. However, opposite results were frequently observed in ta-C films. ta-C film has much higher residual compressive stress due to its high sp3 fraction compared to the DLC films deposited by CVD method. Effect of residual stress on G-peak position is most recommendable parameter in Raman analysis of ta-C, due to its smallest fitting error among many parameters acquired by peak deconvolution of symmetric spectra. In current study, the effect of residual stress on Raman spectra was quantitatively evaluated by free-hang method. ta-C films of different residual stress were deposited on Si-wafer by modifying DC-bias voltage during deposition. The variation of the G-peak position along the etching depth were observed in the free-hangs of 20~30${\mu}{\textrm}{m}$ etching depth. Mathematical result based on Airy stress function, was compared with experimental results. The more reliable analysis excluding stress-induced shift was possible by elimination of the Raman shift due to residual compressiove stress.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.1
• /
• pp.63-69
• /
• 2015

The primary aim of this paper is to evaluate the probabilistic fatigue crack propagation models using the residual of a random variable and to present the probabilistic model fit for the probabilistic fatigue crack growth behavior in Mg-Al-Zn alloys under maximum load conditions. The models used in this study were prepared by applying a random variable to empirical fatigue crack propagation models such as the Paris-Erdogan model, Walker model, Forman model, and modified Forman model. It was verified that the good models for describing the stochastic variation of the fatigue crack propagation behavior in Mg-Al-Zn alloys under maximum load conditions were the 'probabilistic Paris-Erdogan model' and 'probabilistic Walker model'. The influence of the maximum load conditions on the stochastic variation of fatigue crack growth is also considered.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.4
• /
• pp.44-56
• /
• 1989

Recently the residual strength of damaged tubulars under axial compression has extensively been investigated. However, in spite of the possibility of damage onto underwater members of offshore structures as results of collisions, dropped objects and other accidental impacts occurring in service or during fabrication or installation, no research works on the structural behaviour of damaged tubulars under combined loadings including hydrostatic pressure have been reported in the literature. In this paper, a numerical method has been proposed to estimate the residual strength of damaged tubulars under combined loadings, and then the proposed method has been substantiated with corresponding test data. A simple design equation has been derived based upon the results of the parametric study using the proposed method. The accuracy of the predictions using the derived equation is found to be a 10.1% COV(Coefficient of Variation) together with an 1. 037 mean comparing with the test data.