• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.49 no.4
• /
• pp.279-283
• /
• 2004

This experiment was carried out at paddy field (commercial silty loam soil) in the southwestern Korea. Pungsannamulkong, a determinate growth habit, was a relatively high yielding and late maturing cultivar, and Han­namkong, a semi determinate growth habit, was a relatively low yielding and early maturing cultivar. Seeds were sowed at two plants and with a planting density of $70{\times}10cm$ on May 26, 2003. Fertilizer was applied prior to planting at a rate of 3.0-3.0-3.4g $(N-P_2O_5-K_2O)\;per\;m^2$ by all basal fertilizations. Experimental design was a randomized complete block with three replications. Seed yield was higher in Pungsannamulkong by 362g per $m^2$ than in Hannamkong of 260g per $m^2$ Also, the number of pod, number of seed, and number of seed per pod were greater in Pungsannamulkong than in Hannamkong. The number of leaves per $m^2$ showed similar with two soybean cultivars up to August 24 but thereafter it decreased in Hannamkong. The leaf area up to August 4 increased in Hannamkong higher than in Pungsannamulkong, but after that time, Pungsannamulkong had greater leaf area than Hannamkong. The shoot and leaf dry matter of two soybean cultivars from June 23 to August 4 were similar but thereafter, Pungsannamulkong had a significantly greater than Hannamkong. Crop growth rate (CGR), relative growth rate (RGR) and net assimilate rate (NAR) for Punsannamulkong were relatively higher than Hannamkong but leaf area ratio (LAR) and specific leaf weight (SLW) showed higher in Hannamkong. Most of leaves distributed in the ranges of 80-90cm and 60-70cm from the soil surface in Punsannamulkong and Hannamkong, respectively. Pods of Punsannamulkong ranged 10-80cm from the soil surface and most of pods were distributed at 40-50cm. Photosynthetic rate at the flowering stage showed a significant difference between cultivars in the upper most leaf position. There was no significant difference of the photosynthetic rate at $7^{tn}$ leaf at the flowering stage, and the uppermost and 7th leaf position at the seed development stage between two soybean cultivars.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.4
• /
• pp.299-306
• /
• 2019

In this study, a model experiment that simulates the behaviour of the ground composed of several compacted layer was intended to measure the loosened area in the event of a ground cavity through a LAD (Loosened area detector). It was confirmed that the size of the cone diameter was affected by the ground composed of fine grain + granulated soil layered through the model soil. In order to select the appropriate cone type, a scale effect experiment was conducted. From the test results, a micro-cone was chosen for the most suitable indoor model experiment. In the case of applying LAD in this study, the loosening condition of the ground was determined by the rapid change in penetration resistance caused by the difference in the boundary surface and relative density due to the compaction of the ground for indoor model testing. The range of loosened area occurring in the cavity was estimated through the penetration resistance characteristics on the ground, and the failure area was identified through the reduction rate of penetration resistance in the loosening area.

• International Journal of Highway Engineering
• /
• v.20 no.3
• /
• pp.47-57
• /
• 2018

PURPOSES : The permeable pavement type has been rapidly developed for solving problems regarding traffic noise in the area of housing complex and heavy rainwater drainage in order to account for the climate change. In this regards, the objective of this study is to figure out the characteristics of pavement types. METHODS : The laboratory test for deriving optimum asphalt content (OAC) was conducted using the mixtures of the permeable asphalt surface for the pavement surface from Marshall compaction method. Based on its results, the pavement construction at the test field was conducted. After that, the site performance tests for measuring the traffic noise, strength and permeability were carried out for the relative evaluation in 2 months after the traffic opening. The specific site tests are noble close proximity method (NCPX), Light falling deflectometer test (LFWD) and the compact permeability test. RESULTS : The ordered highest values of the traffic noise level can be found such as normal dense graded asphalt, drainage and porous structure types. In the results from LFWD, the strength values of the porous and drainage asphalt types had been lower, but the strength of normal asphalt structure had relatively stayed high. CONCLUSIONS :The porous structure has been shown to perform significantly better in permeability and noise reduction than others. In addition to this study, the evaluation of the properties and the determination of the optimum thickness for the subgrade course under the porous pavement will be conducted using ground investigation technique in the further research.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.86-88
• /
• 2006

The novel linear- (V-LUM) and cross-type macromonomers (C-VUM) of vinyl-terminated bifunctional polyurethane were synthesized and applied to the dispersion polymerization of styrene and MMA in ethanol. The existence of the vinyl terminal groups and the grafted macromonomer with styrene and PMMA was verified using 1H NMR and 13C NMR. Monodisperse polystyrene (PS) microspheres were successfully obtained above 15 wt % of macromonomer relative to styrene. The macromonomer can efficiently stabilize higher surface area of the particles compared to a conventional stabilizer, PVP. The grafting ratio of the PS calculated from 1H NMR linearly increased up to 0.048 with 20 wt % of the macromonomer and the high molecular weights (501,300 g/mol) of PS with increased glass transition and enhanced thermal stability were obtained. Furthermore, the stable and monodisperse PMMA microspheres having a weight-average diameter of $5.09{\mu}m$ and a good uniformity of 1.01 were obtained with 20 wt% L-VUM. The molecular weight increased, but the size of the PMMA particles decreased with the macromonomer concentration due to the increased stabilizing effect. The molecular weight of the PMMA was approximately two fold higher than that by a conventional PVP. The L-VUM acts as a reactive stabilizer, which gives polyurethane-grafted PS or PMMA with a high molecular weight. In addition, the XPS result showed that the C-PS (PS using the C-VUM) was anchored with a larger amount of PEG than that of the L-PS (PS using the L-VUM) on the particle surface. Thus, the reaction and stabilizing mechanism of the macromonomers for the formation of PS particles is proposed.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.189-206
• /
• 2003

During tunnel excavation in urban area a systematic monitoring is important for the purpose of determination of support type and quantity, as well as for the control of stability of both surface structures and the tunnel itself due to the frequently, and in many cases, abruptly changing ground condition. In Austria absolute displacement monitoring methods have replaced relative displacement measurements by geodetic methods to a large extent. Prompt detection of weak ground ahead of the tunnel face as well as better adjustment of excavation and support to the geotechnical conditions is possible with the help of the improved methods of data evaluation on sites. Deformation response of the ground to excavation starts ahead of the tunnel face, therefore, the deformation and state of the tunnel advance core is the key factor of the whole deformation process after excavation. In other words, the rigidity and state of the advance core play a determining role in the stability of both surface structures and the tunnel itself. This paper presents the results from detailed three-dimensional numerical studies, exploring vertical displacements, vector orientations and extrusions on tunnel face during the progressive advancement for the shallow tunnel in various geotechnical conditions.

• BMB Reports
• /
• v.33 no.3
• /
• pp.221-227
• /
• 2000

The distribution of barbiturates in the model membranes of total lipids (SPMVTL) and total phospholipids (SPMVPL) extracted from synaptosomal plasma membrane vesicles was determined by employing a fluorescent probe technique. The two fluorescent probes 2-(9-anthroyl)stearic acid and 12-(9-anthroyl)stearic acid were utilized as probes for the surface and the hydrocarbon interior of the outer monolayer of the SPMVTL and SPMVPL, respectively. The Stern-Volmer equation of fluorescent quenching was modified to calculate the relative distribution. The analysis of preferential quenching of these probes by barbiturates indicates that pentobarbital, hexobarbital, amobarbital and phenobarbital are predominantly distributed on the surface area, while thiopental sodium has an accessibility to the hydrocarbon interior of the outer monolayer of the SPMVTL and SPMVPL. From these results, it is strongly suggested that the more effective penetration into the hydrocarbon interior of the outer monolayer of the membrane lipid bilayer could result in a higher general anesthetic activity.

• Food Science and Biotechnology
• /
• v.15 no.6
• /
• pp.825-832
• /
• 2006

The effect of alginate coating in combination with an anti-browning agent on increasing the post-cutting shelf life and improving the quality of minimally processed apple cubes was studied during storage at room temperature for 5 days. A simple coating technique involving the chemical cross-linkage of alginate by calcium was used. Statistical-based experimental designs were applied to improve the quality of the alginate-coated apple cubes (ACAC). Plackett-Burman design was first used to determine the main factors influencing the preservation of the original weight, color, and texture of ACAC. Among these variables, alginate concentration ($X_1$), dipping time ($X_2$), and dipping temperature ($X_3$) significantly influenced the ACAC weight and color (confidence levels above 90%). Subsequently, the effects of the 3 main factors were further investigated by a central composite design. The polynomial models developed by response surface methodology were adequate to describe the relationships between the studied factors and the responses. Overall optimization conducted by superimposing the curves of the responses enabled the determination of an optimal range of the independent variables in which the five responses were simultaneously optimized. The point chosen as representative of this optimal area corresponded to $X_1=2.98%$, $X_2=0.85\;min$, and $X_3=55^{\circ}C$ and under these conditions the model predicted weight loss=0.522%, relative hardness=1.517, ${\Delta}E=1.423$, browning inhibition=93.403%, and ${\Delta}L=0.158$.

• Clean Technology
• /
• v.22 no.1
• /
• pp.9-15
• /
• 2016

xAl-yZr mixed oxide catalysts with different molar ratios of Al/(Al+Zr) were prepared by a co-precipitation method and its catalytic performance was compared in the iso-propanol dehydration as a model reaction. The catalysts were characterized by X-ray diffraction (XRD), differential thermal analysis (DTA), N₂ adsorprion-desorption, NH₃ temperature programmed desorption (NH₃-TPD), and iso-propanol TPD analyses. The addition of Al into ZrO₂ promoted the formation of relatively small particles with large surface areas and retarded the transformation of teragonal phase to monoclnic phase. NH₃-TPD results revealed that the relative acidity of the catalysts increased along with the increase of Al molar ratio. The catalytic activity for the dehydration of iso-propanol to propylene was also increased with the same tendency. The catalytic activity could be correlated with high surface area, acidity and easy desorption of iso-propanol.

• Asian-Australasian Journal of Animal Sciences
• /
• v.33 no.10
• /
• pp.1691-1698
• /
• 2020

Objective: The study sought to estimate the relationship between body surface temperature (BST) and temperature humidity index (THI) and to present the validity of THI as a heat stress index in the field. Methods: Eight Hanwoo heifers (20 to 32 month) were examined in a field trial, with a space allowance of 10 ㎡ per head. The BST was measured using an infrared thermographic camera. The BST of five body regions (eyes, hindquarters, nose, part of horns, and ears), ambient temperature (AT), and relative humidity (RH) were measured 7 times daily (07, 09, 11, 13, 15, 17, and 19 h) during each season with three replicates. Results: The THI ranged 34.0 to 56.9 during spring (AT, -1.0℃ to 13.4℃), 75.1 to 84.7 during summer (AT, 24.9℃ to 33.6℃), 55.8 to 70.9 during autumn (AT, 13.0℃ to 26.0℃) and 17.5 to 39.2 during winter (AT, -10.4℃ to 1.0℃). In the regression analysis, the coefficient of determination (R²) between THI and BST was 0.88, 0.72, 0.83, 0.86, and 0.85 for the eyes, hindquarters, nose, part of horn, and ears area, respectively. This indicates that BST has a strong correlation with AT and RH. Expression equations were estimated as Y (THI) = 31.54+0.1085X (BST of eyes) and Y (THI) = 30.48+0.1147X (BST of hindquarters) by simple linear regression analysis in this experiment. Conclusion: Consequently, the upper bound for heat stress estimation can be specified ranging from THI of 65 (eyes) to 70 (hindquarters). From this we can expect a precise feeding system for Korean native cattle in the field.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.23 no.2
• /
• pp.145-154
• /
• 1990

Amounts of total suspended matter(TSM) around the Kori waters have been monitored for two years to understand the dispersal pattern of fine-grained sediment. Average concentration of the TSM is $3\~4\;mg/\iota$ in the surface and $3.5\~5\;mg/\iota$ in the near-bottom water. Semi-quantitative analysis for the four major clay minerals in TSM is also performed. The average relative abundance of each clay mineral such as illite, kaolinite, chlorite, and smectite is $65\%,\;17\%,\;17\%$, and $1\%$, respectively. It seems that the majority of recent fine-grained sediment deposited around the Kori area is derived from the Nakdong River. The texture of surface sediment is also dominated by fine-grained fraction leading up to $90\%$ of silt and clay content. The grain size decreases seaward progressively.