• Journal of the Korean Wood Science and Technology
• /
• 제48권5호
• /
• pp.676-684
• /
• 2020

This study was carried out in order to evaluate the bending creep deflection of glulams and bolted glulams beam-to-beam connection with steel-gusset plates and bolts under changing relative humidity. The two types of glulam beams (130 mm in width, 175 mm in thickness, and 3000 mm in length) used in this study were made from domestic larch and composed of seven layers. The gussets were made of 8-mm-thick steel plates. Creep testing was conducted under constant loads in an uncontrolled environment. The test was carried out in a room that was well ventilated through a window. The creep test specimens were loaded for 33,000 hours. A bending creep test for the glulams was conducted through four-point loading. The applied stresses were 20% and 30% of the MOR in the static bending test for the glulam and bolted glulam, respectively. After 33,000 hours, the creep deflection of the glulam at a 20% stress level increased by 39% to 99%, while the creep deflection of the glulam at a 30% stress level increased by 27% to 67%, as compared with instantaneous elastic deflection. The relative creep increased during autumn and winter, and recovered during spring and summer. The relative creep of the bolted glulams was changed abruptly by loading up to 5,000 hours, but stabilized after 5,000 hours, and then gradually increased until 33,000 hours. The relative creep of the bolted glulam increased 2.11 times on average after 33,000 hours.

• Journal of the Korean Wood Science and Technology
• /
• 제35권5호
• /
• pp.7-15
• /
• 2007

To evaluate the durability of finger-jointed woods according to change of humidity conditions, four types of finger-jointed woods glued with different kinds of adhesives and finger pitches were made with Sitka spruce, and the effect of humidity conditions on creep performances was investigated. The shape of creep curves differed among humidity conditions, and the inclination of creep curves was greatest in 85%RH, and lowest in 65%RH. Their creep curves showed a linear behavior beyond approximately one hour, regardless of humidity conditions. The A values of the creep curves fitted to power law increased with increasing relative humidity, whereas the A' values were in order of 30 > 85 > 65%RH unlike the A values. The initial deformation increased with increasing relative humidity, whereas the creep deformation unlike the initial deformation was in order of 85 > 30 > 65%RH, and it was found that the creep deformation of finger-jointed woods indicated the smaller amount in air-dry moisture content rather than in a low moisture content less than 30%RH. Finger-jointed woods with 6.8 mm (L) pitch had the greater creep amount than in those with 4.4 mm (S) pitch in all humidity conditions. The difference of creep amount between both adhesives in all humidity conditions was small. Relative creep at 240 hr was greatest as 62.2~71.9% in 85%RH, and the values indicated 2.1~2.6 times that of 30%RH and 3.0~3.6 times that of 65%RH and were equal or slightly greater than that of solid spruce.

• 한국구조물진단유지관리공학회 논문집
• /
• 제27권5호
• /
• pp.75-83
• /
• 2023

프리스트레스트 콘크리트 철도 교량에서 발생하는 과다한 솟음 문제를 분석하는 연구의 일환으로, 이 논문에서는 콘크리트 구조물의 시간에 따른 솟음 증가량을 나타내는 크리프 계수에 대하여 산정 방법과 분석 결과를 제시한다. 설계기준의 크리프 계수 산정식을 사용하여 국내 12개 지역의 기후 조건(상대습도와 온도)을 적용한 크리프 계수를 구하고, 기후 조건에 대한 지역별 및 재하 시기별 차이가 크리프 계수에 미치는 영향을 분석한다. 재하 초기에 많이 발생하는 크리프를 적절하게 산정하기 위하여 시기별 기후조건을 구분하여 고려하도록 시간 단계해석 방법을 적용하여 상세 분석한다. 지역의 평균 기후조건을 적용하여 구한 크리프 계수는 시간 단계 해석으로 구한 크리프 계수의 평균과 비슷하며, 시간 단계 해석을 통하여 크리프 계수에 미치는 상대습도와 온도의 상쇄, 중첩 효과 및 재하 초기 기후 효과를 적절하게 나타낼 수 있음을 보인다.

• International Journal of Concrete Structures and Materials
• /
• 제9권4호
• /
• pp.453-462
• /
• 2015

A critical review on existing creep theories in calcium-silicate-hydrate (C-S-H) is presented with an emphasis on several fundamental questions (e.g. the roles of water, relative humidity, temperature, atomic ordering of C-S-H). A consensus on the rearrangement of nanostructures of C-S-H as a main consequence of creep, has almost been achieved. However, main disagreement still exists on two basic aspects regarding creep mechanisms: (1) at which site the creep occurs, like at interlayer, intergranular, or regions where C-S-H has a relatively higher solubility; (2) how the structural rearrangement evolutes, like in a manner of interlayer sliding, intra-transfer of water at various scales, recrystallization of gelled-like particles, or dissolution-diffusion-reprecipitation at inter-particle boundary. The further understanding of creep behavior of C-S-H relies heavily on the appropriate characterization of its nanostructure.

• Journal of the Korean Wood Science and Technology
• /
• 제48권5호
• /
• pp.608-617
• /
• 2020

For efficient use and expansion of domestic small- and medium-diameter woods, cross-laminated wood panels composed of tropical hardwoods and domestic temperate woods were fabricated, and the bending creep behavior under long-term loading was investigated. The bending creep curve of the cross-laminated wood panels showed an exponential function graph with a sharp increase at the top right side. The wood panel composed of a teak top layer and larch core and bottom layers recorded the highest initial deformation, and that composed of a merbau top layer and tulip core and bottom layers showed the lowest initial deformation. Creep deformation of the cross-laminated wood panels showed the highest value in that composed of a teak top layer and larch core and bottom layers and showed the lowest value in that composed of a merbau top layer and tulip core and bottom layers. The obtained creep deformation is 3.1-4.3 times that of merbau, however, it is remarkably lower than that of tulip and larch. The highest relative creep was recorded by the wood panel composed of merbau top layer and larch core and bottom layers, whereas that composed of the teak top layer and tulip core and bottom layers showed the lowest relative creep.

• 한국지반환경공학회 논문집
• /
• 제19권9호
• /
• pp.21-28
• /
• 2018

본 연구에서는 남해안 모래의 장기 크리프 침하 특성을 평가하고자 상대밀도별로 표준압밀시험을 수행하였다. 실험 결과 최종 하중 단계에서의 누적 침하량은 상대밀도가 증가할수록 감소하였고, 간극비의 변화량도 감소하였다. 모래의 장기 크리프 침하비율을 분석한 결과, 전체 침하량에 대해서 상대밀도에 따라 4.7~11.0%의 크리프 침하가 발생하였다. 또한, Schmertmann et al. (1978)의 크리프 계수, Beta는 0.17~0.40(평균 0.21)로 평가되었고, 일정 하중단계 이상이 되면 일정한 값으로 수렴하는 경향을 보였다. 층두께에 따른 크리프 계수가 큰 차이가 없는 것으로 평가되어 실제 현장 층두께와 무관하게 크리프 계수를 적용할 수 있는 것으로 확인되었다.

• Journal of the Korean Wood Science and Technology
• /
• 제33권5호통권133호
• /
• pp.57-65
• /
• 2005

Following our previous reports for finger-jointed woods with various finger profiles studied for the efficient use of small diameter logs and woods containing various defects, twelve types of finger-jointed woods glued with three kinds of adhesives and with two sizes of finger pitches were made with sitka spruce and red pine. The effects of the adhesives and finger pitches on bending creep performances of finger-jointed woods were investigated. The shape of creep curves differed among the used adhesives and finger pitches of finger-jointed woods for both tested species. Their creep curves showed a linear behavior beyond about one hour, and the N values fitted to power law increased with increasing finger pitches. The initial deformation increased with increasing finger pitches, regardless of the tested species and kinds of adhesives, whereas the effect of finger pitches on the creep deformation was not clear. For finger-jointed woods glued with polyvinyl acetate (PVAc) resin, creep failure occurred in 106 hours after the load was applied. And the difference of the creep compliance between finger-jointed woods glued with resorcinol-phenol formaldehyde (RPF) resin and aqueous vinyl urethane (AVU) resin was small. The ratios for creep performances of finger-jointed woods glued with RPF resin and AVU resin versus solid wood were higher in creep deformation than initial deformation for both species, and the difference between both adhesives was not found. The relative creep decreased with increasing finger pitches, and the marked differences was not found between RPF resin and AVU resin.

• Journal of the Korean Wood Science and Technology
• /
• 제45권6호
• /
• pp.689-702
• /
• 2017

In this study, with the view to using effectively small and medium diameter Korean domestic woods as structural materials, cross-laminated woods were manufactured by using six species of Korean domestic softwoods and hardwoods, and bending creep properties were investigated for each species. The creep curves showed the shape of the exponential function plot, and the creep curves after 1 hour were able to estimate by fitting it to the power law. The initial and creep compliances of cross-laminated woods showed the higher values in wood species with a low density than in that with a high density. And by cross-laminating, the initial and creep compliances perpendicular to the grain considerably decreased, the extent of the decrease was found to be greater in creep deformation than in initial deformation. The creep anisotropies of cross-laminated woods were considerably decreased by cross-laminating. The relative creep of $C_{\bot}$ type composed of perpendicular-direction lamina in the faces decreased 0.59 - 0.64 times compared to that of $P_{\bot}$ type composed of perpendicular-direction laminae in all layers, and that for $C_{\parallel}$ type composed of parallel-direction laminae in the faces increased 1.5 - 1.6 times compared to that of $P_{\parallel}$ type composed of parallel-direction laminae in all layers.

• Composites Research
• /
• 제32권6호
• /
• pp.382-387
• /
• 2019

상대습도와 온도가 PET 필름의 점탄성 특성에 미치는 영향을 조사하기 위해 RH-DMA를 이용하여 single frequency strain mode 시험, stress relaxation mode 시험, creep 시험을 수행하였다. 상대습도는 10%, 30%, 50%, 70%, 90%를 적용하고 온도는 single frequency strain mode 시험의 경우 30~95℃, stress relaxation mode 시험의 경우 30℃ 와 70℃, creep 시험의 경우 5~95℃를 고려하였다. 연구결과에 따르면 상대습도가 높아지면 저장탄성계수와 손실탄성계수는 낮아지며 손실탄성계수의 최대값은 상대습도의 변화에 큰 영향을 받지 않고 거의 일정해진다. 이완탄성계수는 초기에 급격히 감소하다가 일정한 값을 가지며 높은 온도에서는 상대습도의 변화에 민감해진다. 변형률 회복는 초기에 급격히 증가하며 온도가 높아지면 이완 탄성계수와 마찬가지로 상대습도에 민감하게 변한다. 크리프 컴플라이언스의 증가 정도는 온도가 높아지면 커지며 유리전이온도보다 온도가 높아지면 증가 정도는 더욱 커진다. 시간-온도 중첩법을 통해 구해지는 마스터 선도를 이용하면 상대습도와 온도 등의 운용 조건에서의 장기 성능을 예측할 수 있는 정보를 얻을 수 있다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.19-24
• /
• 2004

A number of creep data were collected and filed for type 316LN stainless steels through literature survey and experimental data produced in KAERI. Using these data, polynomial equations for predicting creep life were obtained for Larson Miller (L-M), Qrr-Sherby-Dorn (O-S-D) and Manson-Haferd (M-H) parametric methods. In order to find out the suitability for them, the relative standard error (RSE) and standard error of estimate (SEE) values were obtained by statistical process of creep data. The O-S-D parameter showed better fitting to creep-rupture data than the L-M or the M-H parameters, and the three parametric methods did not generate the large difference in the SEE and the RSE values.