• Journal of the Korea Concrete Institute
• /
• v.24 no.6
• /
• pp.685-693
• /
• 2012

The yield strength of shear reinforcement is restricted in the present design codes. In this study, the possibility of the yield strength increase in shear reinforcement is evaluated according to ACI318-08, EC2-02 and CSA-04 by comparing the experimental and calculated results. Three cases were used to analyze the shear strength of the beam. One had no limitation in the yield strength of shear reinforcement, another had restriction on the yield strength of shear reinforcement, and the other had a restriction on the yield strength of shear reinforcement and the shear reinforcement ratio. The study results showed that the case with unlimited shear reinforcement yield strength predicted the test result better than other two cases. Even though the rebar yield strength higher than the strength required in present code was applied to existing shear design equation, the result was reasonable. Therefore, the design equation seemed to be appropriate even if the high-strength shear reinforcement is used in practice based on the existing shear design method.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1999.04a
• /
• pp.239-246
• /
• 1999

recently there have been many destructive seismic events in Kobe Japan in 1995 and in Northridge California USA in 1994. etc. The Korean Bridge Design Standard Specifications adopted the seismic design requirements in 1992. Comparing the earthquake magnitude in Korea with those in the west coast of the USA it may be said that the current seismic design requirements of the Korean Bridge Design Standard Specifications provides too conservation design results especially for transverse reinforcement details and amount in reinforced concrete columns. This fact usually makes construction problems in concrete casting due to transverse reinforcement congestion. And the effective stiffness Ieff depends on the axial load P(Ag{{{{ {f }_{ck } }}) and the longitudinal reinforcement ratio Ast/Ag and it is conservative to use the effective stiffness Ieff than the gross section moment Ig. Seismic design for transverse reinforcement content of concrete column is considered of extreme-fiber compression strain R-factor axial load and stiffness etc.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.6
• /
• pp.35-43
• /
• 2017

The minimum reinforcement ratio is an important design factor to prevent a brittle failure in RC flexural members. A minimum reinforcement ratio is presented by assuming an effective depth of cross-section and moment arm lever in CDC and KHBDC. In this study, it suggests that a rational method for minimum reinforcement ratio is calculated by material model and force equilibrium. As results, a minimum reinforcement ratio using a p-r curve in KHBDC is evaluated about 52~80% of recent design code's value and it induces an economical design. And also, a ductility capacity in case of placing this minimum reinforcement amount is evaluated about 89% of recent design code's value, but ductility in a member is 7 or more, so it has a sufficient ductility capacity. Therefore, it is judged that a minimum reinforcement ratio using p-r curve has a theoretical rationality, safety and economy in a flexural member design.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.141-146
• /
• 2002

The purpose of this study is to develop a reasonable design for transverse confinement reinforcement considering ductility and required transverse confinement reinforcement of RC bridge columns. In order to develop relationships between the curvature ductility and required transverse confinement reinforcement for design purpose, the analysis using the computer program NARCC have been carried out for parametric studies. Based on the results from the parametric studies, an equation for calculating the required transverse confinement reinforcement based on ductility demand was developed for seismic design of RC bridge columns. The equations proposed by this study will provide more reasonable and more effective design guidelines for performance-based seismic design of RC bridge columns.

• Journal of Positioning, Navigation, and Timing
• /
• v.10 no.2
• /
• pp.113-120
• /
• 2021

The Distance Measuring Equipment (DME) is a ground-based aircraft navigation system and is considered as an infrastructure that ensures resilient aircraft navigation capability during the event of a Global Navigation Satellite System (GNSS) outage. The main problem of DME as a GNSS back up is a poor positioning accuracy that often reaches over 100 m. In this paper, a novel approach of applying deep reinforcement learning to a DME pulse design is introduced to improve the DME distance measuring accuracy. This method is designed to develop multipath-resistant DME pulses that comply with current DME specifications. In the research, a Markov Decision Process (MDP) for DME pulse design is set using pulse shape requirements and a timing error. Based on the designed MDP, we created an Environment called PulseEnv, which allows the agent representing a DME pulse shape to explore continuous space using the Soft Actor Critical (SAC) reinforcement learning algorithm.

• Proceedings of the IEEK Conference
• /
• 2000.07b
• /
• pp.677-680
• /
• 2000

The technique of reinforcement learning algorithm is extended to solve the multiobjective control problem for uncertain dynamic systems. A multiobjective adaptive critic structure is proposed in order to realize a max-min method in the reinforcement learning process. Also, the proposed reinforcement learning technique is applied to a multiobjective satisfactory fuzzy logic controller design in which fuzzy logic subcontrollers are assumed to be derived from human experts. Some simulation results are given in order to show effectiveness of the proposed method.

• KIEAE Journal
• /
• v.8 no.5
• /
• pp.61-68
• /
• 2008

For the recycling of the resources and the preservation of the environment, this study's purpose is to measure flexural behavior of the reinforced concrete beams with the major variables like concrete strength, replacement ratio of the recycled aggregate and the waste foundry sand and the tension reinforcement ratio and to present the data of the recycled aggregate used for the structure design. The experiment on the flexural behavior resulted in the followings. The ultimate strength of recycled R/C beam was manipulated proportionate to the tension reinforcement ratio, however the strength instantly decreased after passing the ultimate load due to the destroyed concrete of the compression side. The deflection at the maximum load varied from the tension reinforcement ratio by 5.5 times. The test specimen with the tension reinforcement ratio less than $0.5{\rho}b$ showed constant curve without change in the load from the yield to the ultimate load in contrast to the distinctive plastic region where the displacement was rising. Although the strain of main tension steel with the reinforcement ratio indicate different, the design of recycled concrete member can be applied for current design code for reinforced concrete structure as the ratio of tension reinforcement district the under the reinforcement ration in a balanced strain condition.

• Archives of design research
• /
• v.20 no.3 s.71
• /
• pp.97-106
• /
• 2007

This study examines whether the reinforcement theory could be effectively applied to teaching assistant robots between a robot and a student in the same way as it is applied to teaching methods between a teacher and a student. Participants interacted with a teaching assistant robot in a 3 (types of robots: positive reinforcement vs. negative reinforcement vs. both reinforcements) by 2 (types of participants: honor students vs. backward students), within-subject experiment. Three different types of robots, such as 'Ching-chan-ee' which gives 'positive reinforcement', 'Um-bul-ee' which gives 'negative reinforcement', and 'Sang-bul-ee' which gives both 'positive and negative reinforcement' were designed based on the reinforcement theory and the token reinforcement system. Subjective impressions and preferences were measured according to the types of robots and the types of participants. Participants preferred the positive reinforcement robot most, and the negative reinforcement robot least. Regarding the number of stimulus, in case of the negative reinforcement robot for honor students, the less the stimulus is, the more positive the impressions toward the robot are. The findings demonstrate that the reinforcement interaction is important and effective factor which determines children's preferences and impressions for teaching assistant robots. The results of this study can be implicated as an effective guideline to interaction design of teaching assistant robots.

• International Journal of Concrete Structures and Materials
• /
• v.18 no.1E
• /
• pp.49-54
• /
• 2006

Confinement is major contribution to bond strength between reinforcement steel bars and concrete. Cover thickness, bar spacing and transverse reinforcement are the key confinement factors of current provisions for the development and splices of reinforcement. However, current provisions are still too complicated to determine the values of the confinement, which need to be well delineated in the process of design. In this study, an experimental work using beam-end and splice specimens was performed to examine the effect of concrete cover on bond strength. The results of this experiment and previously available data are analyzed to identify the effects of confinement on bond strength. From this reevaluation, new provisions for the development and splices of reinforcement are proposed. The provisions suggest some limitations in the confinement index. The new provisions will allow the engineers to use a simple and yet satisfactory and appropriate method or a precise approach for design to determine the values of confinement on the calculation of development and splice lengths.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.205-212
• /
• 2002

Carbonate rocks such as limestone are susceptible to solution and show numerous solution cavities. For the construction of the structures such as bridge foundations and tunnel on the limestone cavities, the geological unconformities developed in the bed rocks, cavity systems and the filling types of solution deposits should be surveyed and analyzed. And also, the stability of structures on the limestone cavities must be taken into consideration in the view of the geotechnical engineering. As a result of analysis of the foundation settlement, an economic and effective reinforcement method is to be proposed and the construction by the proposed method is to be accompanied with verification of reinforcement effect. This paper is a case study of design and construction for the reinforcement of bridge foundations on the limestone cavity covered with thick bedded colluvial soils.