• Korean Journal of Optics and Photonics
• /
• v.16 no.3
• /
• pp.196-200
• /
• 2005

A 40 channel arrayed-waveguide grating (AWG) filter operating in C-band and L-band wavelength regions has been fabricated using PLC (Planar Lightwave Circuit) processes with 0.75 refractive index difference. Its design was optimized for matching the center wavelength with the ITU-recommended wavelength. The characteristics of the fabricated C-band AWG are as follows; average insertion loss < 2.5 dB, polarization-dependent loss < 0.3 dB, non-adjacent crosstalk >35dB, and the loss uniformity of 0.8 dB. In the L-band AWG, wavelength accuracy is below 0.02nm.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.636-641
• /
• 2012

In this study, we have investigated highly efficient nanoscale surface corrugated light emitting diodes (LEDs) for the enhancement of light extraction efficiency (LEE) of nitride semiconductor LEDs. Nanoscale indium tin oxide (ITO) surface corrugations are fabricated by using the conformal nanoimprint technique; it was possible to observe an enhancement of LEE for the ITO surface corrugated LEDs. By incorporating this novel method, we determined that the total output power of the surface corrugated LEDs were enhanced by 45.6% for patterned sapphire substrate LEDs and by 41.9% for flat c-plane substrate LEDs. The enhancement of LEE through nanoscale surface corrugations was studied using 3-dimensional Finite Different Time Domain (FDTD) calculation. From the FDTD calculations, we were able to separate the light extraction from the top and bottom sides of device. This process revealed that light extraction from the top and bottom sides of a device strongly depends on the substrate and the surface corrugation. We found that enhanced LEE could be understood through the mechanism of enhanced light transmission due to refractive index matching and the increase of light scattering from the corrugated surface. LEE calculations for the encapsulated LEDs devices also revealed that low LEE enhancement is expected after encapsulation due to the reduction of the refractive index contrast.

• Electrical & Electronic Materials
• /
• v.8 no.3
• /
• pp.352-356
• /
• 1995

Native oxide layer on MCT (HgCdTe) has been grown uniformly in H$\_$2/O$\_$2/ electrolyte through anodic oxidation method. It has been determined that anodic oxidation of HgCdTe in H$\_$2/O$\_$2/ electrolyte proceeds immediately with the input of constant currents without any induction time required for anodic oxideation in KOH electrolyte. Oxide layer with the resistivity of 2*10$\^$10/.ohm.cm and the refractive index of 2.1 suggested the possibility of well matching combination layer with ZnS for MCT MIS device. XPS results indicated that the major components of oxide layer grown in H202 solution is TeO$\_$2/ with the possibility of small amounts of CdTeO$\_$3/.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.905-909
• /
• 2002

Characteristics of reflective LCDs, which have gained a lot of notice in recent years, rely largely on optical design of circular polarizers and the quarter-wave plates, as a component. Important design includes wavelength dispersion, viewing angle, uniformity of display and matching of refractive index. Our work has contributed to improving performance of reflective LCDs by enhancing the characteristics of polymer film using stretching and optical lamination technologies. To design that offers higher contrast and wider viewing angle, we have discovered that it is necessary to control viewing angle variation of the polarizing axis in order to compensate for the viewing angle of the polarizing film as well as the optical anisotropic properties of liquid crystal. Applying this technology to circular polarizers used for reflective LCDs enables design of wide viewing angle circular polarizers. In order to realize higher contrast for reflective LCDs, it is also necessary to design other optical materials including polarizing films. For design of hybrid optical film, it is particularly necessary to reduce surface reflection and interface reflection. This paper also reports our findings concerning this topic.

• Journal of electromagnetic engineering and science
• /
• v.13 no.2
• /
• pp.137-139
• /
• 2013

A compact metamaterial (MTM)-based tunable phase shifter consisting of four unit cells with a simple DC bias circuit has been designed at 2.4 GHz. The variable series capacitors and shunt inductors that are required to be loaded periodically onto a host transmission line are realized employing only chip variable capacitors (varactors). In addition, the proposed phase shifter requires only one DC bias source to control the varactors, with the matching condition of the MTM line automatically satisfied. The measured phase shifting range is $285.2^{\circ}$ (from $-74.2^{\circ}$ to $211^{\circ}$). The measured insertion loss is approximately 1.5 dB. The circuit/electromagnetic-simulated and measured results are in good agreement.

• Journal of Sensor Science and Technology
• /
• v.30 no.3
• /
• pp.131-138
• /
• 2021

The optimization of the specifications of vertical silicon on insulator (SOI) slot optical waveguides suitable for integrated-optical biochemical sensors was performed through computational analysis of the confinement factor of the guided mode distributed in the slot in addition to analytical examination of the TE mode. The optimized specifications were confirmed based on sensitivity in terms of the change in the refractive index of the biochemical analyte. When the slot width, rail width, and height were set to 120 nm, 200 nm, and 320 nm, respectively, the confinement factor was evaluated to be about 56% and the sensitivity was at least 0.9 [RIU/nm].

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.359-359
• /
• 2014

In this study, surface plasmon resonance structures for the selective and the enhanced transmission of infrared light were designed. In order to relieve the large discontinuity of refractive index between air and metal hole array, $Si_3N_4$ was used as the impedance matching layer. Experimental parameter were calculated and determined in advance by the rigorous coupled wave analysis (RCWA) simulation, and then the experiment was carried out. A 2-dimensional metal hole array structures were patterned on the size of $1{\times}1cm^2$ GaAs substrate using photolithography process, and 5 nm thick Ti, 50 nm thick Au were deposited by E-beam evaporator, respectively. Subsequently, $Si_3N_4$ films with various thicknesses (150, 350, 550, and 750 nm) were deposited by plasma enhanced chemical vapor deposition (PECVD). For the comparison, transmittance of specimens with and without $Si_3N_4$ was measured using Fourier transform infrared spectroscopy (FTIR) in the range of $2.5-15{\mu}m$. Furthermore, the surface and the cross-sectional images were collected from the specimens by scanning electron microscopy (SEM). From the results, it was demonstrated that the transmittance was enhanced up to 80% by the deposition of 750 nm $Si_3N_4$ at $6.23{\mu}m$. It has advantage of enhanced transmission despite the simple fabrication process.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.5
• /
• pp.339-342
• /
• 2005

In long-period fiber grating (LPFG) to be made up optical fiber sensors, resonance coupling occurs between the forward-propagating core mode and cladding modes at the wavelength that satisfy the Phase matching condition. The resonance wavelength and the coupling strength depends strongly on the external environment like temperature, strain, and ambient index. These characteristics can be utilized for various applications as optical fiber sensors. fabrication of optical fiber gratings is typically based on the photosensitivity effect, i.e. the permanent change of the refractive index upon irradiation of the UV beam, and therefore, fabrication of the optical fiber with high phososensitivity is an important part of the research on optical fiber gratings. In this work, we measured the effort of to-doping of boron on the index difference between the core and cladding of the optical fiber and the sensitivity of the LPFC to the temperature and bending changes. We observed that the index difference between the core and the cladding decreased by $(1.69{\times}10^{-4}/SCCM)$ and the temperature sensitivity of the resonance wavelength shirt decreased by $(0.01145nm/^{\circ}C/SCCM)$. The dependence or the bending-induced changes or the transmission characteristics of LPFG on the tore-cladding index difference was investigated experimentally. The measurement results indicate that the bending sensitivity increases as the index difference decreases.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.4
• /
• pp.133-140
• /
• 2006

The growth characteristics and properties of large size $SrAlF_5$ single crystals are described and compared with those of $BaMgF_4$. Transmission spectra in the vacuum ultraviolet wavelength region indicate a high transparency of $SrAlF_5$ (about 90% without considering surface reflection loses) down to 150 nm, on contrast to the optical loses observed for $BaMgF_4$. The ferroelectric character of $SrAlF_5$ is evidenced by the reversal of the spontaneous polarization in a hysteresis loop. The higher potential of $SrAlF_5$ in comparison with $BaMgF_4$ for the realization of all-solid-state lasers in the ultraviolet wavelength region by the quasi-phase matching (QPM) technique is pointed out. $SrAlF_5$, besides a higher grade of transparency, shows a nonlinear effective coefficient similar to that of quartz and uniaxial nature, on contrast to the one order smaller nonlinear coefficient and biaxial character of $BaMgF_4$. The refractive index of $SrAlF_5$ from the ultraviolet to the near-infrared wavelength region is measured by the minimum deviation method. The Sellmeier and Cauchy coefficients are obtained from the fits to the curves of the ordinary and extraordinary refractive indices, and the grating period for the first order QPM is estimated as a function of the wavelength. The poling periodicity for 193 nm SHG from 386 nm is $4{\mu}m$.

• Journal of the Korean Society of Visualization
• /
• v.6 no.2
• /
• pp.33-38
• /
• 2008

The effect of the radial temperature gradient and the presence of slits in the wall of outer of two cylinders involved in creating a Taylor-Couette flow was investigated by measuring the velocity field inside the gap. The slits were azimuthally located along the inner wall of the outer cylinder and the number of slits used in this study was 18. The radius ratio and aspect ratio of the models were 0.825 and 48, respectively. The heating film wrapped around the inner cylinder was used for generating the constant heat flux and we ensured the constant temperature condition at the outer space of the outer cylinder. The velocity fields were measured by using the PIV(particle image velocimetry) method. The refractive index matching method was applied to remove image distortion. The results were compared with plain wall configuration of Taylor-Couette flow. From the results, the presence of slits in the wall of outer cylinder and temperature gradient increased the flow instability.