• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.141-145
• /
• 2002

In this paper, we have implemented the reflection type band-rejection filter by employing the 3-㏈ hybrid and the frequency-selective loads. The frequency-selective loads have been achieved with the 3-pole bandpass filter terminated by a 50-ohm load. The reflection type band-rejection filter is less sensitive to unloaded Q-factor of resonator than the conventional one. Measurements and simulations on the presented band-rejection filter in this paper show the excellent performances in passband and rejection-band.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.9
• /
• pp.1-6
• /
• 1997

A transmission type phase shift attenuator has a poor reflection characteristics at an output port. And that is controlled by the current, its dynamic rnage decreases due to the current limitation. In this paper, to avoid such disadvantages, a reflection type low phase shift attenuator has been designed and measured. As a result, at a center frequency (1855MHz), the sreflection type low pahse shift attenuator has an attenuation of 30dB, within the limit of 3 phase shift and less than -17dB reflection characteristics at both input and output ports. And it demonstrates the peformance of the reflection type low phase shift attenuator is better than the transmission type phase shift attenuator with the same measurement specifications.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.228-233
• /
• 2008

The reflection type photoelastic experiment can be used more effectively than the transparent type photoelastic experiment in industrial fields. However, the reflection type photoelastic experiment for orthotropic material has not been studied. Therefore, the reflection type photoelastic experimental hybrid method for the fracture mechanics of orthotropic material was developed in this research. Comparing the results obtained from this method with those from the hybrid method for isotropic material about the same isotropic specimen, the validity of this method was verified. And then, the reflection type photoelastic experiment for orthotropic material was applied to the orthotropic plates with a central crack of the various inclined angle. Using this hybrid method for the orthotropic material, it is able to obtain stress intensity factors and separate stress components at the vicinity of the crack-tip in orthotropic plates from only the isochromatic fringe patterns of isotropic coating material.

• Journal of the Optical Society of Korea
• /
• v.19 no.5
• /
• pp.467-476
• /
• 2015

Finger vein recognition, which is a promising biometric method for identity authentication, has attracted significant attention. Considerable research focuses on transmission-type finger vein recognition, but this type of authentication is difficult to implement in mobile consumer devices. Therefore, reflection-type finger vein recognition should be developed. In the reflection-type vein recognition field, the majority of researchers concentrate on palm and palm dorsa patterns, and only a few pay attention to reflection-type finger vein recognition. Thus, this paper presents reflection-type finger vein recognition for biometric application that can be integrated into mobile consumer devices. A database is built to test the proposed algorithm. A novel method of region-of-interest localization for a finger vein image is introduced, and a scheme for effectively extracting finger vein features is proposed. Experiments demonstrate the feasibility of reflection-type finger vein recognition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04c
• /
• pp.80-81
• /
• 2008

In this paper, we have designed the Anti-Reflection (AR) coating for 850, 1310 nm(multi type) and 1310, 1550 nm(multi type) wavelength ranges on the ferrule facet of special optical connector. The reflectance of the AR coated ferrule facet is designed under 5% for 850, 1310 nm(multi type) and 1310, 1550 nm (multi type). The average return loss of the AR coated ferrule facet is 47.1 dB.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2006.10a
• /
• pp.95-104
• /
• 2006

A floating-type wave power pump is a device which sends air into water by using wave power. The floating-type wave power pump has the new configuration composed of a curved surface reflection board, a slope, and phase plates. As a result of a water-tank experiment it turned out that the floating-type wave power pump with a curved surface reflection board and a slope raised power and efficiency in the wide wavelength waves. The result of a marine experiment was also preferable. The floating-type wave power pump sends air into the sea by using wave power, so it can be used for the improvement of marine environment. In addition, the floating body constituted of a curved surface reflection board, a slope, and phase plates, is effective as a device to utilize the energy of a wave. Therefore, it can be widely used for a wave power generation, pumping up deep seawater.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.287.2-287.2
• /
• 2014

PV (photovoltaic) has becoming an important industry to invest due to its high robustness and require very little maintenance which goes a long time. Solar cell fabrication involves a few critical processes such as doping to make the N-type and P-type silicon, contact metallization, surface texturization, and anti-reflection coatings. Anti-reflection coating is a kind of surface passivation which ensures the stability, and efficiency of the solar cell. Thus, I will focus on the changes happen to the solar cell due to the reflectance and anti-reflection coating by PC1D. By using the PC1D (solar cell simulation program), I would analysis the effect of reflectance on the N-type cell. At last I will conclude the result regarding what I learned throughout this experiment.

• Environmental Engineering Research
• /
• v.20 no.4
• /
• pp.383-391
• /
• 2015

Transparent type noise barrier is a desirable facility since it provides a secure view to drivers and passengers. However, reflection from this type of barrier could annoy dwellers on the sides of the road. To reduce reflection noise by transparent type barrier, modification can be made to the shapes on the front side and hence get effects by distortion of sound transmission. To achieve this, we have conducted simulation by which the effects of patterned screens of noise barrier on high-ways were investigated. The reduction effects of reflected sounds were evaluated for swelling, swelling with curved, rectangular and V-shaped screen type barriers, compared to the planar panel. The emitting noise was generated by 6-lane road and the patterned noise barriers had shown the reduction effects, especially in swelling and swelling with curved type for middle height dwellers, and the V-shaped screen type for higher elevation dweller. The swelling-type showed a decrease of 0.7~1.2 dB, performing the best diminution effect among the tested noise barriers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.450-451
• /
• 2008

In this paper, we have designed the Anti-Reflection (AR) coating for 850, 1310 nm(multi type) and 1310, 1550 nm(multi type) wavelength ranges on the ferrule facet of special optical connector. The reflectance of the AR coated ferrule facet is designed under 5% for 850, 1310 nm(multi type) and 1310, 1550 nm (multi type). AR thin film was deposited by ion- assisted deposition in low temperature. The average return loss of the AR coated ferrule facet is 47.1 dB.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.2
• /
• pp.161-167
• /
• 2017

This paper presents an effective PPG measurement device in a wrist watch for smart healthcare. PPG can be acquired by measuring absorption of light and PPG measurement device is classified as transmission and reflection type. Reflection type is easy to implement but vulnerable to motion artifact. Moreover, reflection type must use 2 hands at once if the device is implemeted in a wrist watch. This paper describes the implementation of robust transmission type PPG measurement device by using previous developed reflection type device. PPG sensor is clip type and can be separated from the device so that the influence of motion artifact can be reduced. The proposed device can transmit the measured signal in real-time and is useful for smart healthcare. For evaluation of the proposed device, PPG signals are compared with reflection type in the same condition. The results show that the proposed device has 20% improvement in performance.