• Bulletin of the Korean Chemical Society
• /
• 제25권10호
• /
• pp.1463-1464
• /
• 2004

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.115-117
• /
• 2006

The detent force by end-effect has a bad influence on moving coil type Permanent Magnet Linear Synchronous Motor(PMLSM). So, the reduction of detent force by end-effect is especially required for improvement of thrust characteristics. In this paper, in order to reduce detent force by end-effect the auxiliary teeth is installed at the end part of mover and it is optimized by using neural network.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1145-1150
• /
• 2005

The aim of this paper is to investigate the effect of surface texturing on metal surface and to understand the potential of friction reduction through micro-scale dimple to fabricate by photolithography on pin-on-disk test using flat-on-flat contact geometry. It was verify that the friction property with respect to the same pitch has been influence on the size of dimple under lubricated sliding contact. Also, we can recognize from Stribeck curve that the friction property has a connection with the size of dimple. It can explain a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. The friction property has been an effect on the size of surface texture on reduction friction, not only because the density of dimple, but also because the ratio of diameter/pitch. This ratio of approximately 0.5 is recommend under the tested friction condition. It suggested that the ratio of d/p is an important parameter for surface texture design.

• 전기학회논문지
• /
• 제62권7호
• /
• pp.891-897
• /
• 2013

The power system frequency plays an important role in monitoring and controlling the power system. The frequency can be measured through discrete Fourier transform (DFT) coefficients of its positive fundamental frequency. The accuracy of the frequency estimate is severely affected by noise in the power system signal and the leakage effect of the negative fundamental frequency in DFT. This paper proposes a DFT-based frequency estimation algorithm to cope with the noise as well as the leakage effect. In this algorithm, two suitable digital filters are introduced to reduce efficiently frequency estimate error due to the noise. These filters are designed to use a digital bandpass filter and a second-degree integrator. The effectiveness of the proposed algorithm in reduction of frequency estimate error is verified through simulations on noise, harmonics and frequency deviation.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권9호
• /
• pp.397-407
• /
• 2002

A new simulator which predicts the quantum effect in NMOSFET structure is developed. Using the self-consistent method by numerical method, this simulator accurately predicts the carrier distribution due to improved calculation precision of potential in the inversion layer. However, previous simulator uses analytical potential distribution or analytic function based fitting parameter Using the developed simulator, threshold voltage increment and gate capacitance reduction due to the quantum effect are analyzed in NMOS. Especially, as oxide thickness and channel doping dependence of quantum effect is analyzed, and the property analysis for the next generation device is carried out.

• 한국재료학회지
• /
• 제27권8호
• /
• pp.438-444
• /
• 2017

In this work, the effects of hydrogen reduction on the microstructure and thermoelectric properties of $(GeTe)_{0.85}(AgSbTe_2)_{0.15}$ (TAGS-85) were studied by a combination of gas atomization and spark plasma sintering. The crystal structure and microstructure of TAGS-85 were characterized by X-ray diffraction(XRD) and scanning electron microscopy (SEM). The oxygen content of both powders and bulk samples were found to decrease with increasing reduction temperature. The grain size gradually increased with increasing reduction temperature due to adhesion of fine grains in a temperature range of 350 to $450^{\circ}C$. The electrical resistivity was found to increase with reduction temperature due to a decrease in carrier concentration. The Seebeck coefficient decreased with increasing reduction temperature and was in good agreement with the carrier concentration and carrier mobility. The maximum power factor, $3.3{\times}10^{-3}W/mK^2$, was measured for the non-reduction bulk TAGS-85 at $450^{\circ}C$.

• 한국염색가공학회지
• /
• 제21권3호
• /
• pp.26-36
• /
• 2009

The objective of this study is to investigate the elution characteristics of the partial dispositioned hollow nylon filament and the mechanical properties of the eluted fabrics according to the weight reduction conditions. For this purpose, the partial dispositioned nylon/PET composite filament, SDY 70d/48f was prepared, and warp beam was also prepared on the sizing machine using these yarns. Four kinds of woven fabrics were designed with different warp and weft densities and these fabrics specimens were eluted with weight reduction conditions of two kinds of NaOH concentration (30, 40g/l), three kinds of weight reduction temperature (50, 60, $85^{\circ}C$) and two kinds of weight reduction time (30, 60min). The eluting rates of these fabrics specimens were analysed with various weight reduction conditions. The eluting characteristics of these fabrics were discussed with the cross-section of nylon hollow filament measures by SEM. Finally, the mechanical properties of the partial dispositioned hollow nylon fabrics were measured and discussed with various weight reduction conditions.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 제26회 KOSCO SYMPOSIUM 논문집
• /
• pp.241-246
• /
• 2003

Numerical simulations are performed at atmospheric pressure in order to understand the effect of additives on flame speed and the NOx formation in freely propagating $H_{2}/O_{2}/N_{2}$ flames with oxygen enrichments. A chemical kinetic mechanism is developed, which involves 26 gas-phase species and 99 reactions. Under several equivalence ratios and oxygen enrichments, flame speeds are calculated and compared with those obtained from the experiments, the results of which is in good agreement. As hydrogen chloride as additive is added into $H_{2}/O_{2}/N_{2}$ flames with low oxygen enrichments, its chemical effect causes the decrease of flame speed, radical concentration, and the NO production rate. It is found that the chemical effect of additive has much more influence on the reduction of EINO than its physical effect. However, in flames with very high flame temperature the physical effect rather than the chemical effect becomes more important on the reduction of EINO.

• Tribology and Lubricants
• /
• 제36권6호
• /
• pp.359-364
• /
• 2020

Numerical investigation of the groove trap effect with variation in the groove-edge radius of curvature is presented here. The trap effect is evaluated in a two-dimensional sliding bearing using computational fluid dynamics (CFD). This simulation is based on the discrete phase model (DPM) and standard k - ε turbulence model using commercial CFD software, FLUENT. The numerical results are evaluated by comparisons with streamlines and particle trajectories in the grooves. Grooves are applied to various lubrication systems to improve their lubrication characteristics, such as load carrying capacity increment, leakage reduction, frictional loss reduction, and preventing three-body abrasive wear due to trapping effect. This study investigates the grove trapping effect for various groove-edge radius of curvature values and Reynolds numbers. The particle is assumed to be made of steel, with a circular shape, and is injected as a single particle in various positions. One-way coupling is used in the DPM model because the single particle injection condition is applied. Further, the "reflect" condition is applied to the wall boundary and "escape" condition is used for the "pressure inlet" and "pressure outlet" boundaries. From the numerical results, the groove edge radius is found to influence the groove trap effect. Moreover, the groove trap effect is more effective when applying the groove edge radius.

• 해양환경안전학회지
• /
• 제29권6호
• /
• pp.620-627
• /
• 2023

선내 소음은 선원의 거주성과 건강을 위한 중요한 요소 중의 하나로, 선내 소음을 줄이기 위한 노력이 활발하게 진행되고 있다. 소음 저감 방법에는 수동소음제어(PNC) 방법과 능동소음제어(ANC) 방법이 있다. 자동차, 항공기와 달리 선박에서는 ANC를 이용한 소음 저감 대책이 미미한 실정이다. 본 연구는 능동소음제어(ANC)와 같이 방음판과 고주파진동원을 이용하여 기관실에 발생한 소음을 줄이고자 하였다. 이를 위해 아크릴 상자를 이용하여 실험 모형을 만들었고, 4가지 조건별로 소음 저감 효과를 측정하였다. 실험 결과는 다음과 같다. 첫째, 방음판은 55 dB ~ 85 dB까지 모든 범위에서 소음 저감 효과가 있었다. 고주파진동원은 낮은 소음에서 효과가 없었으나, 70.8 dB(A)과 85 dB(A)와 같은 높은 소음에서는 효과가 있었다. 둘째, 방음판과 고주파진동원을 동시에 사용하는 경우에는 최대 -2.2 dB(A) 만큼의 소음 저감 효과가 있었다. 본 실험의 결과는 아크릴판으로 제작한 실험모형에서 얻은 결과로 철판으로 된 실제 선박과 다를 수 있다. 추후 연구에서 실제 선박에서 사용하는 철판(재질과 두께, 구조를 고려)을 이용하여 실험하고자 한다. 이 연구가 선박에 승선하는 선원들의 거주성 향상과 건강 증진에 도움이 되기를 기대한다.