• Journal of the Korean Wood Science and Technology
• /
• v.34 no.2
• /
• pp.30-36
• /
• 2006

Wood fuel must be dried before combustion to minimize the energy loss. Sawdust of Japanese red pine was dried in a batch type fluidized-bed to investigate the drying characteristics of sawdust as a raw material for bio-fuel. The minimum fluidization air velocity was increased as particle size was increased. It took about 21 minutes and 8 minutes to dry 0.08 m-deep bed of particles with average particle size of 1.3 mm from 100% to 10% moisture content at air temperature of $20^{\circ}C$ and $50^{\circ}C$, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.18 no.2
• /
• pp.3-7
• /
• 1990

The chemical Composition of Chinese red pine (Pinus massoniana) submerged in the Yellow Sea for more than 700 years has been examined. When compared to the recent wood, the marked chemical changes in the waterlogged wood is the higher amount of lignin with lesser amount of holocellulose and abnormally high ash content. In the heavily degraded samples, the degradation of cellulose is more severe than that of hemicellulose. However, hemicellulose is much more attacked than the cellulose at the initial stage of deterioration in the sea water. Chemical analysis suggests that the cellulolytic marine microorganisms, whether they are fungi or bacteria. can be regarded as the primary agents for the destruction of the archaeological woods submerged in the sea water.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.4
• /
• pp.93-99
• /
• 1996

In order to investigate the extent of fixation of new water-borne preservatives in blocks of pinus densiflora sapwoods the streaming potential through the column with preservative treated wood was measured at various conditions. The rates of leachability of ingredients in the treated wood were estimated by the measurement of electric conductivity of the solution with the leached components. The solution was also analyzed by Atomic absorption spectrophotometer (AA). As a results, the experimental data indicated that the fixation of CCB, CCFZ and ACQ in wood were relatively unstable. The fixation rates of CCB, CCFZ were improved by increasing heat and drying time. The amounts of the leached ingredients were apparently higher in CCB and CCFZ than in CCA, while the rate of leaching of ACQ was not changed at various drying temperature.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.6
• /
• pp.646-652
• /
• 2014

This study was carried out to test the possibility that tracheid length of red pine growing in Sokwang-ri in Uljin could be used as one of variables to estimate its wood properties. For the study, forest stands of V (500 m a.s.l.) and VIIII (900 m a.s.l.) age class plots were selected in the region, and three trees in each plot were investigated. The tracheid length was separately measured for early- and latewood. It took approximately 25 and 40 years for V and VIIII age class stands, respectively, until the length was stabilized. The lengths in latewood were 3.14 (V age class) and 3.30 (VIIII age class) mm, and in earlywood 2.98 (V age class) and 3.15 (VIIII age class) mm. The lengths in latewood therefore were longer than in earlywood and the lengths for VIIII age class were longer than for V age class. However, the ratio between their lengths in early- and latewood was the same as 0.96 in all age classes. It might be verified whether this ratio can be used as a variable to test the wood property according to provinces by comparing it with others.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.6
• /
• pp.762-771
• /
• 2017

Predicting the amount and distribution of moisture content within wood allows calculating the various mechanical dynamics of the wood as well as determining the drying time. For boxed-heart wood with a large cross-section, since it is difficult to measure the moisture content of the interior, it is necessary to predict the moisture content distribution. This study predicted the moisture movement in boxed-heart red pine timber, during high temperature drying, by using the three-dimensional finite difference method for the efficient drying process. During drying for 72 h, the predicted and actual moisture content of the tested wood tended to decrease at a similar rate. In contrast, the actual moisture content at 196 and 240 h was lower than predicted because surface checking of the wood occurred from 72 h and excessive water emission was unexpectedly occurred from the checked and splitted surface.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.5
• /
• pp.511-526
• /
• 2018

Effects of heat treatment on the characteristics of Royal paulownia (Paulownia tometosa) wood were investigated. The results were compared with those of Suwon silver poplar (Populus tementiglandulosa) and Korean red pine (Pinus densiflora) woods. The wood samples of the three species were treated at $160^{\circ}C$, $180^{\circ}C$, $200^{\circ}C$ and $220^{\circ}C$ in an electric furnace for 2 hours. The changes of color, density, mass loss, and relative crystallinity were investigated before and after heat treatment. The lightness ($L^*$) decreased rapidly from $200^{\circ}C$ in all species. There were no change in red-green chromaticity($a^*$) and yellow-blue chromaticity($b^*$) of Royal paulownia and poplar woods with increasing temperature. Whereas, yellow-blue chromaticity($b^*$) of Korean red pine wood decreased sharply from $200^{\circ}C$. Royal paulownia wood showed appreciable color change(${\Delta}E^*$) after heat treatment above $180^{\circ}C$. Poplar and pine woods, however, presented significant color change from $160^{\circ}C$. Color change of the three wood species increased rapidly with increasing temperature. Mass loss of the three wood species by heat treatment was the highest in the Royal paulownia wood and the lowest in the pine wood. Mass loss and relative crystallinity increased and density decreased slightly with increasing temperature. Consequently, it is revealed that Royal paulownia wood showed considerable differences in the temperature of color change, weight loss and change of relative crystallinity compared to the other wood species.

• Fire Science and Engineering
• /
• v.32 no.5
• /
• pp.6-14
• /
• 2018

This study was carried out with respect to the heat release rate (HRR) properties of building wood. Heat release characteristics were measured using a cone calorimeter (ISO 5660-1) with four kinds of wood. The time to ignition measured after the combustion in $25kW/m^2$ external heat flux was 35 to 55 s. Time to ignition of both lauan and red pine was marked with the most delayed value in each of 54 s, 55 s. The maximum heat release rate ($HRR_{peak}$) was $156.87{\sim}235.1kW/m^2$, and the risk of early fire was highest in spruce. Total heat release of red pine was obtained in the highest value with $114.2MJ/m^2$. The mean effective heat of combustion of Japanese cedar was 19.1 MJ/kg and the highest among the samples. Fire risk of wood by FPI was orderly increased from lauan ($0.2468s{\cdot}m^2/kW$), red pine ($0.2339s{\cdot}m^2/kW$), spruce ($0.2308s{\cdot}m^2/kW$) to Japanese cedar ($0.2231s{\cdot}m^2/kW$). Fire risk of wood by FGI get increased from lauan ($0.5088kW/m^2{\cdot}s$), red pine ($0.5111kW/m^2{\cdot}s$), Japanese cedar ($2.8522kW/m^2{\cdot}s$) to spruce ($3.0662kW/m^2{\cdot}s$). Therefore, the risk of fire on the heat release characteristics of woods were found that spruce and Japanese cedar showed the high value compared with the other specimens.

• Journal of Mushroom
• /
• v.11 no.1
• /
• pp.24-31
• /
• 2013

As a result of advenced research, Penicillium growth inhibition effect in media of cauliflower mushroom by different LED lighting color inhibited all treated groups, but blue wavelength treatment group was unfitted for culture of cauliflower mushroom due to lots of spore of penicillium. So, to investigated characteristics of mycelial growth of cauliflower mushroom according to different LED wavelength and LED wavelength color. As a results, all red wavelength treatment groups found highest mycelial growth tendency. Thus, mycelial growth investigated different quantity of red lighting wavelength conditions. The quantity of lighting wavelength was low intention, 1.41 ${\mu}mol/m^2S$ treatment group found highest mycelial growth. Effects of mycelial growth by subculture found difference of statistical in one time to carry out a subculture treatment group. Mycelial growth by different quantity of LED lighting in different media composition of wood chip media indicated highest trend in the Korean pine treatment groups. To cultured treatment group for 84th days found difference of statistical, when a quantity of LED lighting red wavelength 2.11 ${\mu}mol/m^2S$ treated in wood chip of the Korean pine media. In conclusion, good culture condition of cauliflower mushroom estimated quantity of red lighting wavelength 2.11 ${\mu}mol/m^2S$ in wood chip media of the Korean pine for 84th days.

• Journal of the Korean Wood Science and Technology
• /
• v.28 no.1
• /
• pp.42-47
• /
• 2000

This study was designed to investigate the effect of treatment variables on CCA treatment of Japanese red pine (Pinus densiflora), Japanese larch (Larix leptolepis), and ezo spruce (Picea jezoensis) round posts. Variables included were duration of initial vacuum (30, 45, or 60 minutes) and maximum pressure applied (8.5, 10.5, or 14.0 kg/$cm^2$), and maximum pressure was maintained until refusal point was reached. Regardless of wood species, extending the duration of initial vacuum more than 30 minutes did not affect treatability. Increasing pressure did not affect preservative penetration; however, preservative retention was affected by pressure levels, particularly at higher level (14.0 kg/$cm^2$). Preservative penetration depth of Japanese red pine met a minimum requirement specified by Notification of Korean Forestry Administration (No. 1999-8) for hazard class H5 of CCA-treated wood. Penetration of preservative in both Japanese larch and ezo spruce was not deep because of shallow sapwood thickness of these species, so pretreatment such as incising should be considered if these species are treated with preservatives. Although retention in Japanese red pine was not significantly increased even with 14.0 kg/$cm^2$, that of refractory Japanese larch and ezo spruce was significantly increased with the application of 14.0 kg/$cm^2$. Effect of treatment variables on refusal time was unclear; however, it is cleared that the refusal time was shortened with the increase in sapwood thickness.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.5
• /
• pp.666-675
• /
• 2020

This study investigated mechanical characteristics of pine trees in Yeongdong (Goseong-gun), Yeongseo (Hongcheon-gun), and Yeongnam (Bonghwa-gun) to define differences in the material quality among pine trees of the three regions. The compressive strength, hardness and shear strength of pine trees of each region were measured. There were no differences in the compressive strength of the juvenile woods among the regions, while the heartwood and sapwood in Bongwha generally showed the highest compressive strength followed by those in Hongcheon and in Goseong. The hardness of the cross-section of pines in Bonghwa was the highest, and in terms of the hardness of the radial and tangential sections, pines in Goseong topped the list.. There were no difference among heartwoods of each region in terms of the shear strength, but, but sapwood from Bonghwa had higher shear strength than those of the other two regions, which may be attributed to differences in tracheid length and microfibril angle among pines in each region. This study identifies the quality differences among pines of different region, and therefore, is expected to add value by helping choose the domestic pine tree material effectively and selectively, and also select a plus tree.