• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.391-394
• /
• 2006

The paper deals with the experimental GNSS receiver built at the Czech Technical University for experiments with the real GNSS signal. The receiver is based on software defined radio architecture. Receiver consists of the RF front end and a digital processor based on programmable logic. Receiver RF front end supports GPS L1, L2, L5, WAAS/EGNOS, GALILEO L1, E5A, E5B signals as well as GLONASS L1 and L2 signals. The digital processor is based on Field Programmable Gate Array (FPGA) which supports embedded processor. The receiver is used for various experiments with the GNSS signals like GPS L1/EGNOS receiver, GLONASS receiver and investigation of the EGNOS signal availability for a land mobile user. On the base of experimental GNSS receiver the GPS L1, L2, EGNOS receiver for railway application was designed. The experimental receiver is also used in GNSS monitoring station, which is independent monitoring facility providing also raw monitoring data of the GPS, EGNOS and Galileo systems via internet.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.182-185
• /
• 2008

The thermal performance of air receiver with a change of flow direction for dish solar collector. This system is installed and operated in Incheon, Korea. The thermal capacity of the system is about 5 kW thermal. The aperture diameter of the cylindrical-shape receiver which is made of stainless steel is 100 mm, and the height is 210 mm. Experiments are being carried out to investigate the thermal performance variation of the receivers with several design parameters such as the shape of the receiver, the flow directions and the flow rate of air. First, air flows into the upper part of the receiver, which is the opposite side of the aperture. After the air flows through the inside receiver, that goes out of the receiver through 3 exits which are located near the aperture. Second, air flows into the backside of the receiver, Which is the forward side of the aperture. After the air flows through the inside receiver, that goes out of the receiver through 1 exit. The results show that the system efficiency and receiver efficiency increase as the volume flow rate increases as expected.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.1
• /
• pp.71-76
• /
• 2014

In this paper, we proposed the 1-channel monopulse receiver which has the new configuration and described the operation procedures. Also, we compared and analyzed the proposal receiver and the general 3-channel monopulse receiver. As a result, it is apparent that the monopulse ratio of the proposal receiver is equal to that of the 3-channel monopulse receiver. The proposal receiver achieve the simple receiver configuration and the simple tracking procedures, as contrasted with the 3-channel monopulse receiver. Also, the proposal receiver has advantages in terms of size, weight, cost and power. Because the proposal monopulse receiver require 1-channel receiver and need not the signal processor in comparison with 3-channel monopulse receiver which require 3-channel receiver and need the signal processor.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.12
• /
• pp.3-9
• /
• 2015

In this paper, we propose the operation procedures of the 1-channel monopulse receiver which achieves the new configuration. Also, we analyzed the monopulse ratio and the target angle accuracy of the fabricated receiver by using the monopulse signal generator developed for verifying the proposal equipment. As a result, it is apparent that the monopulse ratio of the proposal receiver is equal to that of the 3-channel monopulse receiver. Also, the fabricated receiver exhibits the target angle accuracy with fewer than 0.1 RMS. The proposal receiver achieves the simple receiver configuration and the simple tracking procedures, as contrasted with the 3-channel monopulse receiver. Also, the proposal receiver has advantages in terms of size, weight, cost and power. Because the proposal monopulse receiver requires 1-channel receiver and needs not the signal processor in comparison with 3-channel monopulse receiver which requires 3-channel receiver and need the signal processor.

• Journal of Astronomy and Space Sciences
• /
• v.27 no.2
• /
• pp.123-128
• /
• 2010

This paper analyzes that the global positioning system (GPS) receiver differential code bias (DCB) has effect on the estimation the ionosphere total electron content (TEC). The data from nine permanent GPS sites of the Korea Astronomy and Space Science Institute (KASI) were used for the estimation of the receiver DCB before (Trimble 4000 SSi) and after (Trimble NetRS) the receiver replacement, using the singular value decomposition method. The results showed that the estimated mean value of the receiver DCB varied from 0.11 ns (nanosecond) to 7.54 ns before the receiver replacement, but the receiver DCBs shoed large values than 20 ns except some stations after the replacement. The receiver DCB showed a relatively large difference by types of the receivers, and, as a result, it had a great effect on the estimation the ionosphere TEC using GPS.

• Aerospace Engineering and Technology
• /
• v.5 no.2
• /
• pp.77-84
• /
• 2006

We should measure receiver tracking threshold and command threshold of the satellite in Integrate System Test (IST) in order to check the normal received power range of LEO(Low Earth Orbit) satellite S-band receiver. In this paper, the algorithm of threshold measurement is examined and the result measured in Integrated System Test is displayed. And than, the factor could have an effect on the result of threshold measurement except the capability of receiver itself was analyzed and compensated as many as distorted value according to that analysis.

• Advances in Energy Research
• /
• v.8 no.3
• /
• pp.155-163
• /
• 2022

The current study presents experimental research on a parabolic trough collector with tube and cavity receivers. The primary concentrating parabolic reflector is designed for an aperture area of 2×2 m² with mirror-polished stainless steel sheet reflectors. The cavity receiver consists of a compound parabolic secondary reflector and a copper tube. Both the conventional tube receiver and the cavity receiver tube are coated with black powder. The experiments are carried out to compare the efficiency of the cavity receiver with the tube receiver for fluid temperature rise, thermal efficiency, and overall losses. The experiments showed significantly higher fluid temperature rise and overall efficiency and lower thermal losses for the cavity receiver compared to the tube receiver within the parameters explored in this study.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.165-168
• /
• 2008

A numerical analysis was conducted to predict the heat transfer characteristics of a solar receiver which is subject to very high heat fluxes and temperatures for solar thermal applications. The concentration ratio of the solar receiver ranges 1000 and the concentrated heat is required to be transported to a certain distance for specific applications. This study deals with a solar receiver according to internal geometry variation incorporating high-temperature heat pipe. The isothermal characteristics in the receiver section is of major concern. The diameter of the solar thermal receiver was 120 mm and the length was 400 mm and the angle of receiver end wall set $90^{\circ},\;60^{\circ},\;45^{\circ},\;30^{\circ}$. And the diameter of the heat pipe was 12.7 mm, 48 axial channels of the same dimensions were attached to the outer wall of the receiver with even spacing in the circumferential direction. The channels are changed to high-temperature sodium heat pipes. Commercial softwares were employed to deal with the radiative heat transfer inside the receiver cavity and the convection heat transfer along the channels. The numerical results are compared and analyzed from the view point of high-temperature solar receiver.

• Proceedings of the KIEE Conference
• /
• 2006.04a
• /
• pp.75-77
• /
• 2006

In this paper, the technology of the conformance test for Broadcast Web Site Service (BWS) which is one of the data services of the T-DMB (Terrestrial Digital Multimedia Broadcasting) is proposed. First, the standard of the BWS Service is introduced and then the method of the conformance test of BWS bitstream and BWS receiver module is provided. A BWS bitstream analyzer is implemented for use in verifying the transmitted BWS bitstreams. To provide a means for the receiver manufactures to verify their own BWS receiver modules, a receiver test suite is developed including BWS test bitstreams and a BWS reference receiver module. The BWS bitstream analyzer includes the analysis function for the conformance test of MOT protocol, HTML, PNG, MNG, JPEG, and Ecma Script. Also, it was actually used for verifying the BWS test bitstreams. In the course of developing a HWS receiver module, 4he BWS receiver module under test can be verified by comparing the results of the BWS reference receiver module with those of the receiver module under test. when the same BWS test bitstreams are fed into the two receiver modules.

• Advances in Energy Research
• /
• v.8 no.1
• /
• pp.21-39
• /
• 2022

In this study, the first law of thermodynamics was used to establish a one-dimensional (1-D) thermal model for parabolic trough receiver (PTR) taking into account the pressure drop and kinetic energy loss effects of the heat transfer fluid (HTF) flowing inside the absorber tube. The validation of the thermal model with data from the SEGS-LS2 solar collector-test showed a good agreement, which is consistent with the previously established models for the conventional straight and smooth (CSS) receiver where the effects of pressure drop and kinetic energy loss were neglected. Based on the developed model and code, a comparative study of the newly designed parabolic trough S-curved receiver versus the CSS receiver was conducted and solar unit's performances were analyzed. Without any supplementary devices, the S-curved receiver enhances the performance of the parabolic trough module, with a maximum of 0.16% compared to CSS receiver with the same sizes and mass flow rates. Thermal losses were reduced by 7% due to the decrease in the temperature of the outer surface of the receiver tube. In addition, it has been shown that from a mass flow rate of 9.5 kg/s the heat losses of the S-curved receiver remain unchanged despite the improvement in the heat transfer rate.