• Journal of Electrical Engineering and Technology
• /
• v.7 no.4
• /
• pp.626-635
• /
• 2012

Most of single frequency GPS receivers utilize low-quality crystal oscillators. If a lowquality crystal oscillator is utilized as the time reference of a GPS receiver, the receiver's clock bias grows very fast due to its inherent low precision and poor stability. To prevent the clock bias becoming too large, large clock jumps are intentionally injected to the clock bias and the time offset for clock steering purpose. The abrupt changes in the clock bias and the time offset, if not properly considered, induce serious accuracy degradation in relative differential positioning. To prevent the accuracy degradation, this paper proposes an efficient and systematic method to eliminate the undesirable clock jump effects. Experiment results based on real measurements verify the effectiveness of the propose method.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.3E
• /
• pp.126-131
• /
• 2002

Ultrasonic measurements are made in egg white to study the properties of the solution of the natural protein. The high-Q ultrasonic resonator method is used to get the ultrasonic absorption spectra over the range 0.2-10 ㎒ at 20℃. It is proportional to the 1.25th power of the frequency. The gelation process caused by heat is studied from the change in the velocity and the absorption. at 3 ㎒ using the pulse echo overlap technique over the range of 10-80℃. The absorption decreases with increasing temperature up to 60℃ where it turns up sharply and rapidly increases thereafter. The strong absorption in the gel region is described by the interaction between the solution and the network structure made of protein. Very slow variation in time elapse is observed after the temperature is quickly raised. It would be a real-time observation of the network building process and the characteristic time for the process is shown to be 400 min. A hysteresis phenomenon with respect to the temperature is observed. This phenomenon is associated with the memorizing effect of the network structure of protein of the gel.

• Smart Structures and Systems
• /
• v.18 no.3
• /
• pp.625-642
• /
• 2016

The rapid technology developments in smartphones have created a significant opportunity for their use in structural live load measurements. This paper presents extensive experiments conducted in two stages to investigate this opportunity. Shaking table tests were carried out in the first stage using selected popular smartphones to measure the sinusoidal waves of various frequencies, the sinusoidal sweeping, and earthquake waves. Comparison between smartphone measurements and real inputs showed that the smartphones used in this study gave reliable measurements for harmonic waves in both time and frequency domains. For complex waves, smartphone measurements should be used with caution. In the second stage, three-dimensional motion capture technology was employed to explore the capacity of smartphones for measuring the movement of individuals in walking, bouncing and jumping activities. In these tests, reflective markers were attached to the test subject. The markers' trajectories were recorded by the motion capture system and were taken as references. The smartphone measurements agreed well with the references when the phone was properly fixed. Encouraged by these experimental validation results, smartphones were attached to moving participants of this study. The phones measured the acceleration near the center-of-mass of his or her body. The human-induced loads were then reconstructed by the acceleration measurements in conjunction with a biomechanical model. Satisfactory agreement between the reconstructed forces and that measured by a force plate was observed in several instances, clearly demonstrating the capability of smartphones to accurately assist in obtaining human-induced load measurements.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2008.04a
• /
• pp.479-480
• /
• 2008

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2007.10a
• /
• pp.394-396
• /
• 2007

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2010.04a
• /
• pp.496-497
• /
• 2010

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2009.10a
• /
• pp.93-94
• /
• 2009

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2006.10a
• /
• pp.171-172
• /
• 2006

• Proceedings of the Korea Water Resources Association Conference
• /
• 1998.05a
• /
• pp.479-484
• /
• 1998

• Smart Structures and Systems
• /
• v.20 no.3
• /
• pp.385-396
• /
• 2017

The recent advancements in sensing technologies allow us to record measurements from target structures at multiple locations and with relatively high spatial resolution. Such measurements can be used to develop data-driven methodologies for condition assessment, control, and health monitoring of target structures. One of the state-of-the-art technologies, Fiber Optic Strain Sensors (FOSS), is developed at NASA Armstrong Flight Research Center, and is based on Fiber Bragg Grating (FBG) sensors. These strain sensors are accurate, lightweight, and can provide almost continuous strain-field measurements along the length of the fiber. The strain measurements can then be used for real-time shape-sensing and operational load-estimation of complex structural systems. While several works have demonstrated the successful implementation of FOSS on large-scale real-life aerospace structures (i.e., airplane wings), there is paucity of studies in the literature that have investigated the potential of extending the application of FOSS into civil structures (e.g., tall buildings, bridges, etc.). This work assesses the feasibility of using FOSS to predict operational loads (e.g., wind loads) on chain-like structures. A thorough investigation is performed using analytical, computational, and experimental models of a 4-story steel building test specimen, developed at the University of Southern California. This study provides guidelines on the implementation of the FOSS technology on building-like structures, addresses the associated technical challenges, and suggests potential modifications to a load-estimation algorithm, to achieve a robust methodology for predicting operational loads using strain-field measurements.