• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.5
• /
• pp.8-13
• /
• 2001

The make a decision for building remodeling, the economical value of the remodeled building should be analyzed and existing situation of the building system should be checked. For the energy issues related to the building remodeling process, careful diagnosis and re-designs of existing system should be proposed. In this research, the luminous environment for Seoul K Co. headquaters and Seoul S hotel were measured and then the re-design processes of building illumination systems were researched. With measured illuminance quantities of there cases, computer simulations for the existing situation and re-design were conducted.

• Fibers and Polymers
• /
• v.7 no.1
• /
• pp.85-87
• /
• 2006

The tensile-recoil compressional behavior of the carbon nanotube reinforced mesophase pitch (MP)-based composite carbon fibers (CNT-re-MP CFs) was investigated by using Instron and SEM. The CNT-re-MP CFs exhibited improved, or at least equivalent, compressive strength as compared with commercial MP-based carbon fibers. Particularly, when CNT of 0.1 wt% was reinforced, the ratios of recoil compressive strengths to tensile strength of CNT-re-MPCFs were much higher (the difference is at least 10 % or higher) than those for the commercial counterparts and even than those for PAN-based commercial carbon fibers. FESEM micrographs showed somewhat different fractography from that of a typical shear failure as the CNT content increased.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.4
• /
• pp.79-84
• /
• 2020

Induction bending via high-frequency heating is widely used for manufacturing pipe and section steel bends. It allows productivity improvement, unit cost reduction, delivery time compliance, and good mechanical properties. The recent increase in high-end vessels and offshore plants has raised the demand for high-frequency bending, which should improve the product quality and reduce the costs by simplifying the fabrication process; therefore, the characteristics and performance of this technique must be studied and proper design technology is required. During hot pipe bending via induction heating, the outward wall thickness of the pipe is thinned due to tensile stress and this thickness reduction cannot exceed 12.5%. This study focused on pipe bends with a bending curvature of 5D and their optimization design; in particular, the conditions that can both improve the productivity of the high-frequency bending process and keep the maximum thickness reduction below 12.5% were determined.

• Wind and Structures
• /
• v.11 no.3
• /
• pp.179-192
• /
• 2008

In a wind tunnel experiment employing a reduced scale model, Reynolds number (Re) can hardly be respected. Its effects on the aerodynamics of closed-box bridge decks have been the subject of research in recent years. Stonecutters Bridge in Hong Kong is a cable-stayed bridge having an unprecedented central span of 1018m. The issue of Re sensitivity was raised early in the design phase of the deck of Stonecutters Bridge. The objective of this study is to summarise the results of various wind tunnel experiments in order to demonstrate the effect of Re on the steady state aerodynamic force coefficients. The results may provide an insight on the choice of scale for section model experiments in bridge design projects. Computational Fluid Dynamics (CFD) analysis of forces on bridge deck section was also carried out to see how CFD results are compared with experimental results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.10A
• /
• pp.1020-1030
• /
• 2006

As the Terrestrial DMB(T-DMB) has been launched, service providers are focusing on finding a business model as well as preparing the variety of data services. So, the need for development of the CAS(Conditional Access system) is urgently required and its domestic standardization is also in progress. This Paper proposes design and implementation methods of an Ensemble Re-multiplexer and receiver platform for its verification that can be used for the CAS system in T-DMB. And, with transmitting ensemble stream scrambled by the proposed Ensemble Re-multiplexer, we verified their performance by do-scrambling and decoding according to scramble mode at the receiver platform.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.6
• /
• pp.153-158
• /
• 2017

Reducer is a device to transmit and change torque and speed from drive shaft to driven shaft with excellent transmission efficiency, and it is widely used in many areas today. Reduction gear consists of two axes, gear, bearing supporting axes, and housing. The simplest method to transmit rotation or power to multiple axes is to attach circular plates to two axes and contact each other. However, in this case, if increasing number of rotations or if contact pressure is small, because of slipping, it cannot transmit power. For problems for the current reducer case, it is heavy and its assembling and repair is difficult. In addition, there are few studies about manufacturing and performance testing of worm gear reducer, causing lack of the foundation to improve the product competition and the performance.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.3
• /
• pp.26-31
• /
• 2005

An efficient estimation of the aerodynamic characteristics for missile configurations is essential in the preliminary stage of a missile design. In this study, a Missile DATCOM family code based on the semi-empirical method was utilized for this purpose. In order to check the accuracy and reliability of the code several test cases have been considered: subsonic flow with high angles of attack and supersonic flow with moderate angles of attack. It turned out that the code in general provides prediction in qualitative agreement with the experimental data and results by other works. Finally, the code was applied to a more complicated missile configuration with canard and freely spinning tail fin.

• Nuclear Engineering and Technology
• /
• v.54 no.9
• /
• pp.3540-3550
• /
• 2022

The supercritical carbon dioxide (S-CO₂) Brayton cycle is an important energy conversion technology for the fourth generation of nuclear energy. Since the printed circuit heat exchanger (PCHE) used in the S-CO₂ Brayton cycle has narrow channels, Rayleigh-Bénard (RB) convection is likely to exist in the tiny channels. However, there are very few studies on RB convection in supercritical fluids. Current research on RB convection mainly focuses on conventional fluids such as water and air that meet the Boussinesq assumption. It is necessary to study non-Boussinesq fluids. PRB convection refers to RB convection that is affected by horizontal incoming flow. In this paper, the computational fluid dynamics simulation method is used to study the PRB convection phenomenon of non-Boussinesq fluid-supercritical carbon dioxide. The result shows that the inlet Reynolds number (Re) of the horizontal incoming flow significantly affects the PRB convection. When the inlet Re remains unchanged, with the increase of Rayleigh number (Ra), the steady-state convective pattern of the fluid layer is shown in order: horizontal flow, local traveling wave, traveling wave convection. If Ra remains unchanged, as the inlet Re increases, three convection patterns of traveling wave convection, local traveling wave, and horizontal flow will appear in sequence. To characterize the relationship between traveling wave convection and horizontal incoming flow, this paper proposes the relationship between critical Reynolds number and relative Rayleigh number (r).

• ETRI Journal
• /
• v.44 no.6
• /
• pp.903-914
• /
• 2022

Mobile and telecommunication networking uses temporary and random identifiers (IDs) to protect user privacy. For greater intelligence and security o the communications between the core network and the mobile user, we design and build a dynamic randomization scheme for the temporary IDs for mobile networking, including 5G and 6G. Our work for ID randomization (ID-RZ) advances the existing state-of-the-art ID re-allocation approach in 5G in the following ways. First, ID-RZ for ID updates is based on computing, as opposed to incurring networking for the re-allocation-based updates, and is designed for lightweight and low-latency mobile systems. Second, ID-RZ changes IDs proactively (as opposed to updating based on explicit networking event triggers) and provides stronger security (by increasing the randomness and frequency of ID updates). We build on the standard cryptographic primitives for security (e.g., hash) and implement our dynamic randomization scheme in the 5G networking protocol to validate its design purposes, which include time efficiency (two to four orders of magnitude quicker than the re-allocation approach) and appropriateness for mobile applications.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.42 no.1
• /
• pp.40-57
• /
• 2018

This study investigated the design practice model based on the creative fashion designer's methodology in fashion education. 'The Design Cycle' was the criterion used to analyze the design method of Demna Gvasalia who is one of the outstanding contemporary designers. After that, this study's practice model was then developed and experimented to verify its effectiveness in design practice as based on Gvasalia's method where ready-to-wear products were firstly dissembled then re-constructed with new designs created based on re-constructed results. To test its effectiveness, a student oriented design workshop was held to extract design results through the practice model; in addition, the students also conducted a survey to evaluate the effectiveness of the method. According to the self-evaluation result, the participants generally accept the design efficiency through the distinctive process. An evaluation by three fashion experts was also conducted. Experts assessed that the model is recommendable for seniors having knowledges on 'Construction', it is appropriate to deal with the trickled-down copying trend that could promote student interest and generate separate results according to different visions. Therefore, it could be accepted that the applicability of this study's practice model was confirmed.