• Journal of Biosystems Engineering
• /
• v.23 no.3
• /
• pp.245-252
• /
• 1998

The structural characteristics of a small scale rice polisher was analyzed to improve its performance. Spraying characteristic of nozzles used for rice polishing was also analyzed by a machine vision system. The internal pressure of the polishing chamber was measured according to outlet resistance, water spraying, and roller shaft speed. In addition, the performance of the rice polisher was evaluated to improve it in the basis of internal pressure in polishing chamber, whiteness, and broken rice ratio of clean rice according to the operating conditions. Actual nozzle discharge rate and drop size were 125 cc/min and 86~97 ${\mu}{\textrm}{m}$, respectively. In the case of water spraying on rices, the internal pressure showed 4.9~9.8N/$\textrm{cm}^2$ increase. broken rice ratio decreased, and there was no difference in whiteness. The internal pressure inueased up to two times with the increase of the outlet resistance. Also, the pressure at the upper part of screen was one and half times as high as the pressure at the lower part. In the case of water spraying rate of 150 cc/min, the roller shaft speed of 850 rpm resulted in no difference in whiteness and decrease of 0.3% in broken rice ratio, comparing to the roller shaft speed of 950 rpm.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1998.06b
• /
• pp.206-216
• /
• 1998

The structural characteristics of small scale rice polisher was analyzed to improve its performance. Spraying characteristic of nozzles used for rice polishing was also analyzed by a machine vision system. The internal pressure of the polishing chamber was measured according to outlet resistance, water spraying , and roller shaft speed. In addition , the performance of the rice polisher was evaluated to improve it in the basis of internal pressure in polishing chamber, whiteness , and broken rice ratio of clean rice according to the operating conditions. Actual nozzle discharge rate and drop size were 125cc/min and 86.97㎛, respectively. In the case of water spraying on rices, the internal pressure showed 4.9-9.8N/㎠ increase, broken rice ration decreased , and there was no difference in whiteness . The internal pressure increased up to two time with the increase of the outlet resistance. Also, the pressure at the upper part of screen was one and half times as high as the pressure at the lower part. In the case of water spraying rate of 150 cc/min, the roller shaft speed of 850 rpm resulted in no difference in whiteness and decrease of 0.3%in broken rice ratio, comparing to the roller shaft speed of 950 rpm.

• Journal of Chest Surgery
• /
• v.25 no.11
• /
• pp.1192-1202
• /
• 1992

Postoperative cardiac outputs and other hernoaynamic values were serially measured in fifteen patients of cyanotic congenital heart disease, after use of blood cardioplegic solution. Cardiac indices showed no change untill eight postoparative hours, then it began to decline to reach as low as 3.22$\pm$0.7L/min/m2 at 12 hours. After then gradual increse occ-ured to recover upto immediate postoperative value at 20 hours. Sharp decrese of heart rate and increse of systemic vascular resistance during 8~16 hours and steady increase of stroke indices during the whole study periods were observed. These observations suggested that the myocardium recovered gradually after open heart surgery, and that the decrease of cardiac indices during 8~16 hours could be a result of decrease of heart rates and increase of afterload. The changes of cardiac indices correlated with the changes of heart rate, postoperative time and mixed venous oxygen saturation [p<0.05]. No other hemodynamic values found to be in statistically significant correlation with the changes of cardiac indices. Left ventricular dysfunction seemed to occur more frequently during 8~12 hours, but it was not statistically significant. [p=0.73] In conclusion, great care must be taken during 2~3 days after the operation of cyanotic congenital heart disease, not to fall into a low cardiac output state, by maintaing adequate heart rates and reducing afterload especially when the systemic vascular resistance increases.

• Journal of Korea Foundry Society
• /
• v.36 no.4
• /
• pp.117-125
• /
• 2016

The effects of the Zn content on the microstructure and corrosion behavior in 1M NaCl solution were investigated in Mg-(0~6)%Zn casting alloys. The MgZn phase was scarcely observed in the Mg-1%Zn alloy, while the Mg-(2~6)%Zn alloy consisted of ${\alpha}$-(Mg) and MgZn phases. With an increase in the Zn content, the amount of the MgZn phase was gradually increased. Immersion and electrochemical corrosion tests indicated that the Mg-1%Zn alloy had the lowest corrosion rate among the alloys, and a further increase in the Zn content resulted in the deterioration of the corrosion resistance. Microstructural examinations of the corroded surfaces and EIS analyses of surface corrosion films revealed that the best corrosion resistance at 1%Zn was associated with the absence of MgZn phase particles in the microstructure and the contribution of Zn element to the formation of a protective film on the surface. A micro-galvanic effect by the MgZn particles led to the increased rate of corrosion at a higher Zn content.

• Journal of Ocean Engineering and Technology
• /
• v.14 no.1
• /
• pp.23-28
• /
• 2000

The fatigue crack growth behavior of the cold-rolled STS 304 steel developed for membrane material of LNG storage tank was examined experimentally at 293K, 153K and 111K. The fatigue crack growth rate(do/dN) tends to increase as the stress ratio (R) increases over the testing temperature when compared at the same stress intensity factor range($\Delta$K). The effect of R on do/dN is more explicit at low temperatures than at room temperature. The resistance of fatigue crack growth at low temperatures is higher compared with that at room temperature which is attributed to the extent of strain-induced martensitic transformation at the crack tip. The temperature dependence of fatigue crack growth resistance is gradually vanished with an increase in $\Delta$K which correlates with a decreasing fracture toughness with decreasing temperature. Fractographic examinations reveal that the differences of the fatigue crack growth characteristics between room and low temperature are mainly explained by the crack closure and the strengthening due to the martensitic transformation.

• Progress in Superconductivity and Cryogenics
• /
• v.15 no.4
• /
• pp.34-38
• /
• 2013

According to the increase of electric consumption nowadays, power system becomes complicated. Due to this, the size of single line-to-ground fault from power system also increases to have many problems. In order to resolve these problems effectively, an Superconducting Fault Current Limiter(SFCL) was proposed and continuous study has been done. In this paper, an SFCL was combined to the neutral line of a transformer. An superconductivity has the characteristics of zero resistance below critical temperature. because of this, SFCL has nearly zero resistance. so we connecting SFCL to neutral line will not only have any loss in the normal operation but also have the less burden of electric power because of only limiting the initial fault current. We analyzed the characteristics of current, voltage according to the changes of turn ratio of 3 phase system in case of combinations of an SFCL to the neutral line. It was confirmed that the limiting rate of initial fault current by the increase of turn ratio was reduced.

• Pediatric Infection and Vaccine
• /
• v.22 no.3
• /
• pp.178-185
• /
• 2015

Purpose: We investigated trends in antibiotic pressure and the antibiotic susceptibility of gram negative bacteria isolated from Korean children over 10 consecutive years. Methods: From January 2004 to December 2013, the antibiotic susceptibility of Klebsiella pneumoniae, Escherichia coli, Pseudomonas aeruginosa, and Acinetobacter baumannii blood isolates obtained from children <18 years of age was determined according to the 2009 Clinical and Laboratory Standards Institute guidelines. Antibiotic consumption data were also analyzed. Results: The prevalence of K. pneumoniae, E. coli, P. aeruginosa, and A. baumannii bacteremia was 4.6, 3.5, 3.4, and 2.2 cases/1,000 blood cultures/year, respectively. In K. pneumoniae, resistance to the third and fourth cephalosporin did not increase significantly. However, carbapenem-resistant K. pneumoniae first appeared in 2010, and the resistance rate increased to 9% between 2012 and 2013. Resistance to 3rd and 4th cephalosporin increased from 10% to 50% in E. coli, and resistance to carbapenem rose abruptly from 11% to 71% in A. baumannii (P for trend <0.01). However, such an increase of resistance was not observed in P. aeruginosa. There is a positive correlation between the resistance rate of cefepime in E. coli and the consumption of cefepime (r=0.900, P=0.037). Conclusion: The significant burden of antibiotic consumption and the high prevalence of antibiotic resistance to gram negative pathogen isolated from bacteremic children were observed. Empirical antibiotics should be wisely selected, and continued efforts to decrease the overall antibiotic pressure are mandatory, especially in highly resistant situations.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.421-424
• /
• 2000

We have examined the impedance characteristics and the rate characteristics of LPB. As results, the impedance of LPB decreased with increased pressing rate of electrodes, adding amounts of PVdF and VGCF. And the rate characteristics of LPB increased with the a increase of pressure-rate, PVdF and VGCF contents. The rate characteristics of LPB was improved by pressing of electrode and adding of VGCF content. And specific capacity of anode was increased with adding amounts of PVdF. Higher pressing rate of electrodes, higher adding amounts of PVdF and VGCF was necessitated good rate characteristics for lithium polymer battery.

• Journal of the Korean institute of surface engineering
• /
• v.28 no.4
• /
• pp.243-254
• /
• 1995

The fabrication process of Cu-base anode for replacing Ni-base anode of molten carbonate fuel cell was investigated. Electrochemical performance and thermal stability of Cu-base anode were also investigated. Green sheet was prepared by mixing Cu and Ni powder with 1.5wt% methylcellulose and 100wt% water. The pore-size distribution of the Cu-base anode sintered at $800^{\circ}C$ for 30min showed almost uniform pore-size ranging from 4 to 20$\mu\textrm{m}$ and it was considered suitable for MCFC anode. Cu-Ni anode containing between 35 to 50wt% Ni exhibited current density of 111mA/$\textrm{cm}^2$ at 100mV overpotential and it was almost the some value for pure Ni anode. The sintering resistance of Cu-Ni increased with an increase of Ni addition. It was considered that the increase of sintering resistance was due to the decrease of diffusion rate of Cu and Ni with increasing the addition of Ni in Cu-Ni alloy.

• Fashion & Textile Research Journal
• /
• v.1 no.3
• /
• pp.288-295
• /
• 1999

This study was conducted to examine the fatigue phenomenon of mechanical properties in tencel fabrics by repeated washing & shear and tensile deformation. The obtained results are as follows. After performing repeated shear tensile deformation, RT of tencel showed higher increase rate than that of cotton and rayon, whereas its WT and EM was a smaller decrease rate than that of them. This means that tencel's resistance to tensile deformation was the greatest. In the repeated washing and shear tensile deformation, tencel's 2HB, 2HG and 2HG5 showed a remarkable increase rate. In terms of deformation frequency, the greatest change rate appeared at the time of 1000 cycles of repeated shear tensile deformation and 15 times of repeated washing. In the hand value and THV, KOSHI showed a higher increase rate for tencel than for cotton and rayon in both repeated washing and shear tensile deformation, and NUMERI showed a higher increase rate. In the THV the change rate of rayon and cotton could be rarely seen but for tencel, it decreased. tencel's change rate of thermal insulation value by materials was 1.08%, and it increased as the washing frequency increased, compared to the grey fabrics, whereas the change rates of cotton and rayon were 0.74% and 0.22%, respectively. The qmax decreased in the order of cotton>tencel>rayon as the washing frequency increased.