• Korean Journal of Metals and Materials
• /
• v.47 no.12
• /
• pp.828-833
• /
• 2009

As a fundamental study in the development of a distillation process for ferromanganese alloy melts, the evaporation behavior of an electrolytic manganese melt under reduced pressure was investigated. The melt temperature, vacuum degree, surface area of the melt, and reaction time were considered as experimental variables. The amount of vaporized manganese increases linearly as the reaction time increases, and the evaporation of manganese was promoted by increasing the temperature and surface area of the melt. In the pressure range below the equilibrium vapor pressure of manganese, the amount of vaporized manganese per unit surface area of the melt increased sharply with a decrease of the pressure in the reaction chamber. An empirical equation for the evaporation rate of manganese was derived by regression analysis. The evaporation coefficient of manganese was determined to be approximately $3.84{\times}10^{-3}(g{\cdot}K^{1/2})/(Pa{\cdot}cm^2{\cdot}min)$ under the investigated conditions.

• Journal of the Korean Institute of Gas
• /
• v.2 no.3
• /
• pp.49-53
• /
• 1998

It takes quite a long time for an analyzer, such as gas chromatography, to measure a bulk property of a system, which prevents on-line measurements. Also, the cost of installation and maintenance is very high. Consequently, some other means is needed for on-line measurements of properties and the development of soft sensors based on process variables like temperature and pressure is of great interest. In the field of gas industry, the development of a soft sensor which makes indirect on-line measurements of gas compositions and flow rate, is in progress. In this paper, we proposed a hybrid inner model PLS which improved the prediction performance by taking into account the data structure, as an empirical modeling algorithm. When applied to a design of a soft sensor of a distillation tower, the hybrid inner model PLS showed better prediction performance than other methods.

• Toxicological Research
• /
• v.31 no.3
• /
• pp.279-288
• /
• 2015

N-nitrosamines, which are classified as carcinogens by IARC and US EPA, can be easily found in various foods. They are reaction products between nitrogen oxide and secondary amines, but can also be generated during fermentation. Ever since the 1960s, when nitrite, used as a preservative in processed meats, was suspected to generate N-nitrosamines, the usage of the food additive has been debated. However, the benefit of nitrite in food supply could not be ignored and the risk-benefit analysis has become a key issue in the use of the additive. For a risk analysis, an accurate estimation of the hazardous material is necessary; therefore, analytical methods for nitrosamines have continuously evolved from the 1950s. Solid supported liquid-liquid extraction and solid phase extractions have replaced the distillation for the clean-up steps, and tandem mass spectrometry is employed for higher selectivity and sensitivity. In the present study, for a better estimation of N-nitrosamine intake, the total diet study samples were prepared for the N-nitrosamines analysis. In order to obtain the most sensitive results, a partial preparation procedure was developed and modified for different food matrices. Among seven N-nitrosamines (N-nitrosodimethylamine, N-nitrosomethylethylamine, N-nitrosodiethylamine, N-nitrosodibutylamine, N-nitrosopiperidine, N-nitrosopyrrolidine, and N-nitrosomorpholine) analyzed in the present study, N-nitrosodiethylamine has shown the highest detection rate in agricultural foods, while N-nitrosodimethylamine has appeared most frequently in livestock and fishery food products. The concentration of N-nitrosodimethylamine was the highest in seasoning.

• Korean Journal of Food Science and Technology
• /
• v.38 no.5
• /
• pp.621-627
• /
• 2006

To characterize aroma properties of burnt beef reaction flavor manufactured by extrusion, volatile flavor compounds and aroma-active compounds were analyzed by simultaneous steam distillation and solvent extraction (SDE)-gas chromatography-mass spectrometry-olfactometry (GC-MS-O). Hydrolyzed vegetable protein (HVP) was successfully extruded with precursors (glucose, cystine, furaneol, thiamin, methionine, garlic powder, and lecithin) at $160^{\circ}C$, screw speed of 45 rpm, and feed rate of 38 kg/hr. Sixty eight volatile flavor compounds were found in burnt beef reaction flavor. The number of volatile flavor compounds decreased significantly when HVP was extruded either with furaneol-free precursors or without precursors. Twenty seven aroma-active compounds were detected in burnt beef reaction flavor. Of these, methional and 2-methyl-3-furanthiol were the most intense aroma-active compounds. It was suggested that furaneol played an important role in the formation of burnt beef reaction flavor.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.202-206
• /
• 2003

In this study, a modified bituminization technology has been developed, which needs no grinding of the granular resin waste, and enables the solid form to keep its shape stability as good as that of a cemented solid from Also, the study intended to apply the developed technology to the practical treatment of radioactive resin waste. In the experiment, the granular type resin was used and the straight-run distillation bitumen with penetration rate 60/70 was used as the solidifying agent. The PE was used as the additive. The shape stability increased remarkably with the additive of PE, which act as a binder in the solid form. The shape of the solid form was maintained without failure during the long-term exposure test when the additive content of spent PE is more than 10wt%. The proper ranges of bitumen content, PE content and operating temperature are 30-50wt%, 10-20wt% and $180^{\circ}C$ respectively. The bituminized solid form of radioactive resin waste by the technology of this study has the remarkably superior quality than the conventional solid forms, partially for the shape stability.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.12
• /
• pp.1121-1126
• /
• 2010

This study is to investigate the effects of aromatics and T90 for low cetane number (CN) fuels on combustion and exhaust emissions in low-temperature diesel combustion. We use a 1.9-L common rail direct injection diesel engine at 1500 rpm and 2.6 bar BMEP. Low temperature diesel combustion was achieved via a high external EGR rate and strategic injection control. The tested fuels four sets: the aromatic content was 20% (A20) or 45% (A45) and the T90 temperature was $270^{\circ}C$ (T270) or $340^{\circ}C$ (T340) with CN 30. Given the engine operating conditions, the T90 was the stronger factor on the ignition delay time, resulting in a longer ignition delay time for higher T90 fuels. All the fuels produced nearly zero PM because of the extension of the ignition delay time induced by the low cetane number. The aromatic content was the main factor that affected the NOx and the NOx increased with the aromatic content.

• Membrane Journal
• /
• v.33 no.4
• /
• pp.158-167
• /
• 2023

The increasing concerns for environmental pollution and depletion of natural resources have prompted the development of environmentally sustainable technologies. Pervaporation has garnered attention in recent decades due to its low energy consumption, environmental impact, and performance efficiency. This method has been used to separate chemical species and dehydrate organic solvents, as the membranes can be fine-tuned to fulfill the desired selectivity. Several separation processes, such as reverse osmosis and distillation, are being utilized in both experimental settings and industrial applications. However, pervaporation has several advantages, such as low operating pressure and temperature and a higher rejection rate. Nonetheless, the current state of membrane technology alone can't suffice the demands of practical applications. Composite membranes, on the other hand, can leverage the benefits of both organic and inorganic materials. Many studies have effectively incorporated inorganic nanomaterials such as graphene oxide (GO) and MXene (MX) in polymeric membranes to tackle the current limitations. This review investigates the recent development of 2D composite membranes in pervaporation and evaluates performance enhancement.

• Korean Journal of Agricultural Science
• /
• v.30 no.1
• /
• pp.76-88
• /
• 2003

This study exploits the robot system which is necessary in gene study, bio-technology industry. As well, it can achieve the job of DNA chip manufacturing whose use rate has been increased recently. The robot consists of DNA spotting device for spotting DNA on the silylated slide and well plate, bed for fixing well-plate, washing & drying device of washing and drying the pin part of DNA spotting device, distillation-water vessel, and discharge vessel of wash water. We made the term of sticking DNA to the pin on well plate to be 15 seconds. The spot size of DNA was set to be 0.28 mm on the average by bringing the slide into contact with pin for 1 second. At this rate, if DNA is spotted in the minimum space possible of about 0.32mm, it can stick about 8,100 DNA spots on the well plate. Analyzing the procedure: Movement starts. Pin washes, dries, and smears DNA on the well plate. Spots DNA onto 12 chips takes 2 minutes and 50 seconds.

• Journal of Energy Engineering
• /
• v.5 no.2
• /
• pp.160-169
• /
• 1996

Parametric studies are conducted for optimizing the integration design between gas turbine compressor and air separation unit (ASU) of integrated gasification combined cycle power plant. The present study adopts the ASU of double-distillation column process, from which integration conditions with compressor such as the heat exchanger condition between air and nitrogen, the amount and the pressure of extracted air are defined and mathematically formulated. The performance variations of the compressor integrated with ASU are analyzed by combining streamline curvature method and pressure loss models, and the predicted results are compared with the performance test results of actual compressors to verify the prediction accuracy. Using the present performance prediction method, the effects of pinch-point temperature difference (PTD) in the heat exchanger, the amount and the pressure of extracted air on compressor performances are quantitatively examined. As the extraction air amount or the PTD is increased, the pressure ratio and the power consumption of compressor are increased. The compressor efficiency deteriorates as the increase of the flow rate of air extracted at higher pressure level while improving at lower pressure air extraction. Furthermore, through the characteristic curve between generalized inlet condition and efficiency of compressor, optimal integration condition is presented to maximize the compressor efficiency.

• KSBB Journal
• /
• v.16 no.4
• /
• pp.403-408
• /
• 2001

Distillation condensate generated from downstream processing of microbial alcohol fermentation imposes a serious burden to biological wastewater treatment or anaerobic digestion due to its high contents of SS (suspended solids) and TN (total nitrogen), A pilot scale microfiltration of the stillage condensate with a stainless steel SCEPTER membrane of 0.1 ${\mu}$m pore size was carried out to remove SS which was mostly composed of microbial cell residue. A stable permeate flux was achieved when the decanter effluent containing 0.7% of SS was filtered under the conditions of X10 VCR (volume concentration ratio), 2.5 bar of TMP (transmembrane pressure), and 60$^{\circ}C$. When stillage condensate with 2.6% SS was treated directly with microfiltration, VCR below X3 was recommended for a long duration of filtration. The permeate and retentate obtained from microfiltration were recycled to make-up medium of fermentation. Adding permeate or retentate up to 30% of fermentation volume showed no distinguished undesirable influence during the course of alcohol fermentation. Although only slight improvements in the final amount of CO$_2$ evolution and alcohol content were observed, fermentation rate increased so that the required time to reach 450 L/ton of CO$_2$ evolution was shortened to 72% of that with normal media.